![header thumbnail](/images/publishers\astm_cover.gif)
ASTM D 6041 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Specification for Contact-Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings
Hardcopy , PDF
18-08-2023
English
14-11-2018
This specification covers pipe and fittings fabricated by contact molding, for pressures to 150 psi and made of a commercial-grade polyester resin.
Committee |
D 20
|
DocumentType |
Standard
|
Pages |
7
|
ProductNote |
THIS STANDARD ALSO REFERS TO ANSI B16.1,ANSI B18.22
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers pipe and fittings fabricated by contact molding, for pressures to 150 psi and made of a commercial-grade polyester resin. Included are requirements for materials, properties, design, construction, dimensions, tolerances, workmanship, and appearance.
1.2This specification does not cover resins other than polyester, reinforcing materials other than glass fibers or fabrication methods other than contact molding.
Note 1:For the purposes of this specification, the term polyester resin will include both polyester and vinylester resins.
1.3This specification does not cover the design of pipe and fittings intended for use with liquids heated above their flash points.
1.4The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are provided for information purposes only.
1.5The following precautionary caveat pertains only to Section 10, the test methods portion, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 2:There is no known ISO equivalent to this standard.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 5421 : 2015 | Standard Specification for Contact Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM D 2583 : 2013 : REV A | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor (Withdrawn 2022) |
ASTM D 5421 : 1993 | Standard Specification for Contact Molded "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM D 2584 : 2002 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
ASTM F 412 : 2020 : REV A | Standard Terminology Relating to Plastic Piping Systems |
ASTM F 412 : 2021 | Standard Terminology Relating to Plastic Piping Systems |
ASTM D 3681 : 2006 | Standard Test Method for Chemical Resistance of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe in a Deflected Condition |
ASTM D 2584 : 2008 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
ASTM D 2584 : 1994 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
ASTM D 2583 : 2006 | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor |
ASTM D 3567 : 1997 : R2006 | Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
ASTM D 3681 : 2001 : EDT 1 | Standard Test Method for Chemical Resistance of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe in a Deflected Condition |
ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 3681 : 2018 | Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition |
ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 3567 : 2017 : R2022 | Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
ASTM D 2583 : 2013 | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor |
ASTM D 2584 : 2011 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM C 582 : 1995 | Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment |
ASTM D 1599 : 2014 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
ASTM D 1599 : 2014 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
ASTM D 3567 : 1997 : R2002 | Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
ASTM D 1599 : 2018 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
ASTM D 1599 : 1999 : R2011 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
ASTM D 3681 : 2023 | Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition |
ASTM D 638 : 2014 | Standard Test Method for Tensile Properties of Plastics |
ASTM D 1599 : 1999 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
ASTM D 5421 : 2000 | Standard Specification for Contact Molded "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM D 3681 : 2012 : EDT 1 | Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition |
ASTM D 2584 : 1968 | Standard Method Of Test For Ignition Loss Of Cured Reinforced Resins |
ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
ASTM D 5421 : 2005 | Standard Specification for Contact Molded "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM F 412 : 2023 | Standard Terminology Relating to Plastic Piping Systems |
ASTM D 3681 : 2001 | Standard Test Method for Chemical Resistance of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe in a Deflected Condition |
ASTM D 3681 : 1996 | Standard Test Method for Chemical Resistance of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe in a Deflected Condition |
ASTM D 3567 : 1997 | Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
ASTM D 2584 : 2018 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
ASTM D 3681 : 2012 | Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition |
ASTM D 5421 : 2023 | Standard Specification for Contact Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM D 1599 : 1999 : R2005 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
ASTM D 3567 : 2017 | Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
ASTM C 582 : 2023 | Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment |
ASTM D 2583 : 2007 | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor |
ASTM D 1599 : 1999 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
ASTM D 3567 : 1997 : R2011 | Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
ASTM D 2583 : 1995 | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor |
ASTM C 582 : 2009 : R2016 | Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment |
ASTM D 5421 : 2005 : R2010 | Standard Specification for Contact Molded "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM D 638 : 2022 | Standard Test Method for Tensile Properties of Plastics |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.