ASTM D 6751 : 2023
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
Hardcopy , PDF
20-06-2024
English
22-03-2023
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 02
|
| DocumentType |
Standard
|
| Pages |
10
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers four grades of biodiesel (B100) for use as a blend component with middle distillate fuels. These grades are described as follows:
1.1.1Grade No. 1-B S15—A special purpose biodiesel blendstock intended for use in middle distillate fuel applications which can be sensitive to the presence of partially reacted glycerides, including those applications requiring good low temperature operability, and also requiring a fuel blend component with 15 ppm sulfur (maximum).
1.1.2Grade No. 1-B S500—A special purpose biodiesel blendstock intended for use in middle distillate fuel applications which can be sensitive to the presence of partially reacted glycerides, including those applications requiring good low temperature operability, and also requiring a fuel blend component with 500 ppm sulfur (maximum).
1.1.3Grade No. 2-B S15—A general purpose biodiesel blendstock intended for use in middle distillate fuel applications that require a fuel blend component with 15 ppm sulfur (maximum).
1.1.4Grade No. 2-B S500—A general purpose biodiesel blendstock intended for use in middle distillate fuel applications that require a fuel blend component with 500 ppm sulfur (maximum).
1.2This specification prescribes the required properties of diesel fuels at the time and place of delivery. The specification requirements may be applied at other points in the production and distribution system when provided by agreement between the purchaser and the supplier.
1.3Nothing in this specification shall preclude observance of federal, state, or local regulations which may be more restrictive.
Note 1:The generation and dissipation of static electricity can create problems in the handling of distillate fuel oils with which biodiesel may be blended. For more information on the subject, see Guide D4865.
1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 7687 : 2023 | Standard Test Method for Measurement of Cellular Adenosine Triphosphate in Fuel and Fuel-associated Water With Sample Concentration by Filtration |
| ASTM D 7797 : 2023 | Standard Test Method for Determination of the Fatty Acid Methyl Esters Content of Aviation Turbine Fuel Using Flow Analysis by Fourier Transform Infrared Spectroscopy—Rapid Screening Method |
| ASTM D 7545 : 2014 : R2019 : EDT 1 | Standard Test Method for Oxidation Stability of Middle Distillate Fuels—Rapid Small Scale Oxidation Test (RSSOT) |
| ASTM D 7619 : 2022 | Standard Test Method for Sizing and Counting Particles in Light and Middle Distillate Fuels, by Automatic Particle Counter |
| ASTM D 7464 : 2020 | Standard Practice for Manual Sampling of Liquid Fuels, Associated Materials and Fuel System Components for Microbiological Testing |
| ASTM D 8181 : 2019 | Standard Specification for Microemulsion Blendstock for Preparing Microemulsion Test Fuel Oils |
| ASTM D 7797 : 2018 | Standard Test Method for Determination of the Fatty Acid Methyl Esters Content of Aviation Turbine Fuel Using Flow Analysis by Fourier Transform Infrared Spectroscopy—Rapid Screening Method |
| ASTM D 396 : 2021 | Standard Specification for Fuel Oils |
| ASTM D 8149 : 2020 | Standard Practice for Optimization, Calibration, and Validation of Ion Chromatographic Determination of Heteroatoms and Anions in Petroleum Products and Lubricants |
| ASTM D 7963 : 2022 | Standard Test Method for Determination of Contamination Level of Fatty Acid Methyl Esters in Middle Distillate and Residual Fuels Using Flow Analysis by Fourier Transform Infrared Spectroscopy—Rapid Screening Method |
| ASTM D 5771 : 2021 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Optical Detection Stepped Cooling Method) |
| ASTM D 7689 : 2021 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Mini Method) |
| ASTM D 975 : 2022 : REV A | Standard Specification for Diesel Fuel |
| ASTM D 2068 : 2020 | Standard Test Method for Determining Filter Blocking Tendency |
| ASTM D 4737 : 2021 | Standard Test Method for Calculated Cetane Index by Four Variable Equation |
| ASTM D 7042 : 2021 : REV A | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 8183 : 2022 | Standard Test Method for Determination of Indicated Cetane Number (ICN) of Diesel Fuel Oils using a Constant Volume Combustion Chamber—Reference Fuels Calibration Method |
| ASTM D 2500 : 2023 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels |
| ASTM D 8436 : 2022 | Standard Specification for Fluoropolymer-based Materials for Use for Encapsulation of Downhole Cable |
| ASTM D 7806 : 2020 | Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Ester) and Triglyceride Content in Diesel Fuel Oil Using Mid-Infrared Spectroscopy (FTIR Transmission Method) |
| ASTM E 1259 : 2018 | Standard Practice for Evaluation of Antimicrobials in Liquid Fuels Boiling Below 390 °C |
| ASTM D 7687 : 2021 | Standard Test Method for Measurement of Cellular Adenosine Triphosphate in Fuel and Fuel-associated Water With Sample Concentration by Filtration |
| ASTM D 7668 : 2017 | Standard Test Method for Determination of Derived Cetane Number (DCN) of Diesel Fuel Oils—Ignition Delay and Combustion Delay Using a Constant Volume Combustion Chamber Method |
| ASTM D 7861 : 2014 : R2019 | Standard Test Method for Determination of Fatty Acid Methyl Esters (FAME) in Diesel Fuel by Linear Variable Filter (LVF) Array Based Mid-Infrared Spectroscopy |
| ASTM D 7397 : 2021 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Miniaturized Optical Method) |
| ASTM D 7467 : 2020 : REV A | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 2274 : 2014 : R2019 | Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) |
| ASTM D 5772 : 2021 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Linear Cooling Rate Method) |
| ASTM D 7501 : 2022 | Standard Test Method for Determination of Fuel Filter Blocking Potential of Biodiesel Fuel Blendstock (B100) by Cold Soak Filtration Test (CSFT) |
| ASTM D 8290 : 2022 | Standard Test Method for Determination of Fatty Acid Methyl Esters (FAME) in Aviation Turbine Fuel using Mid-Infrared Laser Spectroscopy |
| ASTM D 6217 : 2021 | Standard Test Method for Particulate Contamination in Middle Distillate Fuels by Laboratory Filtration<rangeref></rangeref > |
| ASTM D 7371 : 2014 : R2022 | Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Esters) Content in Diesel Fuel Oil Using Mid Infrared Spectroscopy (FTIR-ATR-PLS Method) |
| ASTM D 8274 : 2020 : REV A | Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Esters) Content in Diesel Fuel Oil by Portable Rapid Mid-Infrared Analyzer |
| ASTM D 5773 : 2021 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Constant Cooling Rate Method) |
| ASTM D 6469 : 2020 | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
| ASTM D 7591 : 2012 : R2017 | Standard Test Method for Determination of Free and Total Glycerin in Biodiesel Blends by Anion Exchange Chromatography |
| ASTM D 1655 : 2022 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 7321 : 2021 | Standard Test Method for Particulate Contamination of Biodiesel B100 Blend Stock Biodiesel Esters and Biodiesel Blends by Laboratory Filtration |
| ASTM D 7398 : 2021 | Standard Test Method for Boiling Range Distribution of Fatty Acid Methyl Esters (FAME) in the Boiling Range from 100 °C to 615 °C by Gas Chromatography |
| ASTM D 8144 : 2022 | Standard Test Method for Separation and Determination of Aromatics, Nonaromatics, and FAME Fractions in Middle Distillates by Solid-Phase Extraction and Gas Chromatography |
| ASTM D 874 : 2013 : REV A : R2018 | Standard Test Method for Sulfated Ash from Lubricating Oils and Additives |
| ASTM D 613 : 2023 | Standard Test Method for Cetane Number of Diesel Fuel Oil |
| ASTM D 613 : 2018 : REV A : EDT 1 | Standard Test Method for Cetane Number of Diesel Fuel Oil |
| ASTM D 874 : 2023 | Standard Test Method for Sulfated Ash from Lubricating Oils and Additives |
| ASTM D 4177 : 2022 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 4177 : 2022 : EDT 1 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.