• Shopping Cart
    There are no items in your cart

ASTM D 6823 : 2008 : R2021

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils

Available format(s)

Hardcopy , PDF

Superseded date

10-08-2024

Superseded by

ASTM D 6823 : 2024

Language(s)

English

Published date

01-11-2021

€67.30
Excluding VAT

Committee
D 02
DocumentType
Standard
Pages
7
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This specification covers four grades of fuel oil made of at least 25 % used lubricating oils. The four grades of fuel are intended for use in various types of fuel-oil-burning industrial equipment and commercial boilers under various climatic and operating conditions. These fuels are not intended for use in residential heaters.

1.1.1Grades RFC4, RFC5L, RFC5H and RFC6 are used lubricating oil blends of increasing viscosity, with or without middle distillate or residual fuel oil, or both, that are intended for use in industrial burners and commercial boilers equipped to handle these types of fuels. This specification is for applications where Specification D6448 would not meet the performance or other requirements of the burner or boiler in question.

Note 1:For information on the significance of the terminology and test methods used in this specification, see Appendix X1.

1.2This specification is for use in contracts for the purchase of fuel oils derived from used lubricating oil and for the guidance of consumers of such fuels. This specification does not address the frequency with which any particular test must be run.

1.3Nothing in this specification shall preclude observance of national or local regulations which can be more restrictive. In some jurisdictions, used oil is considered a hazardous waste and fuels derived from used oil are required to meet certain criteria before use as a fuel.

Note 2:For United States federal requirements imposed on used oil generators, transporters and transfer facilities, reprocessors, marketers, and burners, see 40 CFR Part 279.

Note 3:The generation and dissipation of static electricity can create problems in the handling of distillate burner fuel oils. For more information on the subject, see Guide D4865.

1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.4.1Exception—Table 1 and Table X1.1 include inch-pound values in parentheses for information only.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 7666 : 2012 : R2019 Standard Specification for Triglyceride Burner Fuel

ASTM D 4057 : 2019 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 129 : 2018 Standard Test Method for Sulfur in Petroleum Products (General High Pressure Decomposition Device Method) (Withdrawn 2023)
ASTM D 5291 : 2021 Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants
ASTM D 4865 : 2019 Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems
ASTM D 974 : 2014 : EDT 2 Standard Test Method for Acid and Base Number by Color-Indicator Titration
ASTM D 4865 : 2023 Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems
ASTM D 664 : 2018 : EDT 2 Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
ASTM D 6448 : 2016 Standard Specification for Industrial Burner Fuels from Used Lubricating Oils
ASTM D 664 : 2017 : REV A Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
ASTM D 6448 : 2016 : R2022 Standard Specification for Industrial Burner Fuels from Used Lubricating Oils
ASTM D 482 : 2013 Standard Test Method for Ash from Petroleum Products
ASTM D 4052 : 2018 : REV A Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 1298 : 2012 : REV B : R2017 : EDT 1 Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D 473 : 2007 : R2017 : EDT 1 Standard Test Method for Sediment in Crude Oils and Fuel Oils by the Extraction Method
ASTM D 3828 : 2016 : REV A : R2021 Standard Test Methods for Flash Point by Small Scale Closed Cup Tester
ASTM D 4175 : 2022 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 974 : 2022 Standard Test Method for Acid and Base Number by Color-Indicator Titration
ASTM D 473 : 2022 Standard Test Method for Sediment in Crude Oils and Fuel Oils by the Extraction Method
ASTM D 1298 : 2012 : REV B : R2017 Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D 664 : 2024 Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
ASTM D 5854 : 2019 Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products
ASTM D 445 : 2021 : EDT 2 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 93 : 2019 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
ASTM D 974 : 2021 Standard Test Method for Acid and Base Number by Color-Indicator Titration
ASTM D 445 : 2017 : REV A Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 4175 : 2020 : REV B : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2022 : REV A Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 5291 : 2016 Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants
ASTM D 1796 : 2022 Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
ASTM D 4175 : 2023 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 1552 : 2023 Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and Infrared (IR) Detection or Thermal Conductivity Detection (TCD)
ASTM D 3228 : 2022 Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method
ASTM D 95 : 2013 : R2018 Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation
ASTM D 56 : 2021 : REV A Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM D 7042 : 2021 Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 3828 : 2016 : REV A Standard Test Methods for Flash Point by Small Scale Closed Cup Tester
ASTM D 2622 : 2024 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 4175 : 2022 : REV A : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 56 : 2016 : REV A Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM D 3228 : 2020 Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method
ASTM D 4868 : 2017 Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels
ASTM D 445 : 2019 : REV A Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 4177 : 2022 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 97 : 2017 : REV B Standard Test Method for Pour Point of Petroleum Products
ASTM D 4294 : 2016 : EDT 1 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 2983 : 2021 Standard Test Method for Low-Temperature Viscosity of Automatic Transmission Fluids, Hydraulic Fluids, and Lubricants using a Rotational Viscometer
ASTM D 445 : 2019 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 4175 : 2023 : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2023 : REV A Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2022 : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 2983 : 2022 Standard Test Method for Low-Temperature Viscosity of Automatic Transmission Fluids, Hydraulic Fluids, and Lubricants using a Rotational Viscometer
ASTM D 396 : 2021 Standard Specification for Fuel Oils
ASTM D 4294 : 2021 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 2622 : 2021 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 97 : 2017 : REV B : R2022 Standard Test Method for Pour Point of Petroleum Products
ASTM D 664 : 2011 : REV A Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
ASTM D 445 : 2024 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 445 : 2021 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 1796 : 2011 : R2016 Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
ASTM D 4057 : 2022 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 56 : 2022 Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM D 4052 : 2022 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 7042 : 2021 : REV A Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 4177 : 2020 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 445 : 2018 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 4175 : 2024 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 2983 : 2023 Standard Test Method for Low-Temperature Viscosity of Automatic Transmission Fluids, Hydraulic Fluids, and Lubricants using a Rotational Viscometer
ASTM D 445 : 2021 : EDT 1 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 396 : 2024 Standard Specification for Fuel Oils
ASTM D 4177 : 2022 : EDT 1 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 1552 : 2016 : R2021 Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and Infrared (IR) Detection or Thermal Conductivity Detection (TCD)
ASTM D 95 : 2023 Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation
ASTM D 445 : 2023 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 2622 : 2016 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 93 : 2018 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.