Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN ISO 24817:2017

    Current The latest, up-to-date edition.

    PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION (ISO 24817:2017, CORRECTED VERSION 2018-01-01)

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2017

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National Foreword
    European foreword
    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviated terms
    5 Applications
    6 Summary of key issues
    7 Qualification and design
    8 Installation
    9 Testing and inspection
    10 System testing
    11 Decommissioning
    Annex A (normative) - Design data sheet
    Annex B (normative) - Qualification data
    Annex C (normative) - Short-term pipe
            spool survival test
    Annex D (normative) - Measurement of
            [gamma]LCL for through-wall defect
            calculation
    Annex E (normative) - Measurement of
            performance test data
    Annex F (normative) - Measurement of
            impact performance
    Annex G (normative) - Measurement of
            the degradation factor
    Annex H (informative) - Axial extent of
            repair look-up table
    Annex I (normative) - Installer qualification
    Annex J (informative) - Installation requirements
            and guidance
    Annex K (informative) - Design considerations
    Annex L (informative) - Management of the
            integrity of composite repair systems to
            pipework and vessels
    Bibliography

    Abstract - (Show below) - (Hide below)

    Provides requirements and recommendations for the qualification and design, installation, testing and inspection for the external application of composite repair systems to corroded or damaged pipework, pipelines, tanks and vessels used in the petroleum, petrochemical and natural gas industries.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes SR CEN ISO/TS 24817. (09/2015)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 15649:2001 Petroleum and natural gas industries — Piping
    AWWA M45 : 3 FIBERGLASS PIPE DESIGN
    ISO 527-4:1997 Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
    ASTM G 8 : 1996 Standard Test Methods for Cathodic Disbonding of Pipeline Coatings
    EN 59:2016 Glass reinforced plastics - Determination of indentation hardness by means of a Barcol hardness tester
    ANSI/AWWA C200 : 2017 STEEL WATER PIPE, 6 IN. (150 MM) AND LARGER
    ASTM D 543 : 2014 : REDLINE Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
    ISO 15310:1999 Fibre-reinforced plastic composites Determination of the in-plane shear modulus by the plate twist method
    ISO 11359-2:1999 Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
    AWWA M11 : 2004 STEEL PIPE: A GUIDE FOR DESIGN AND INSTALLATION
    ISO 11357-2:2013 Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step height
    BS EN 13121-1:2003 GRP tanks and vessels for use above ground Raw materials. Specification conditions and acceptance conditions
    ASTM C 581 : 2015 : REDLINE Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service
    ASTM D 696 : 2016 : REDLINE Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer
    ASTM D 790 : 2017 : REDLINE Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
    ISO 10952:2014 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for the inside of a section in a deflected condition
    ISO 75-3:2004 Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
    ASTM D 2992 : 2012 Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
    ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
    EN 1465:2009 Adhesives - Determination of tensile lap-shear strength of bonded assemblies
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    ISO 13623:2017 Petroleum and natural gas industries — Pipeline transportation systems
    ISO 868:2003 Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective