![header thumbnail](/images/publishers\astm_cover.gif)
ASTM D 7445 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding)
Hardcopy , PDF
20-05-2024
English
21-02-2018
Committee |
D 20
|
DocumentType |
Standard
|
Pages |
12
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification establishes requirements for vinyl siding with integral foam plastic backing, where the siding is manufactured from rigid PVC compound. Performance requirements and test methods addressed by this standard include materials properties and dimensions, warp, shrinkage, impact strength, expansion, appearance, and wind load resistance. Methods of indicating compliance with this specification are also provided.
Note 1:Backed vinyl siding is composed of two major components: the siding and the backing. It is intended that the siding portion comply with Specification D3679. Applicable portions of Specification D3679 are included in this specification. Additional requirements that pertain only to the backing as a separate material, or to the combination of siding and backing as a whole, are also included.
1.2Backed vinyl siding shall be tested with the backing material in place or removed, as specified in the applicable requirement or test method.
1.3The use of PVC recycled plastic in this product shall be in accordance with the requirements in Section 4.
1.4Siding produced to this specification shall be installed in accordance with Practice D4756. Reference shall also be made to the manufacturer's installation instructions for the specific product to be installed.
Note 2:Information with regard to siding maintenance shall be obtained from the manufacturer.
1.5The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 3:There is no known ISO equivalent to this standard.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 7793 : 2017 | Standard Specification for Insulated Vinyl Siding |
ASTM D 7793 : 2024 | Standard Specification for Insulated Vinyl Siding |
ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 635 : 2018 | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position |
ASTM D 883 : 2023 | Standard Terminology Relating to Plastics |
ASTM E 84 : 2023 : REV D | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 5947 : 1996 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
ASTM D 1435 : 2013 | Standard Practice for Outdoor Weathering of Plastics |
ASTM D 3679 : 2006 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 2244 : 2021 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 3892 : 2015 : R2020 | Standard Practice for Packaging/Packing of Plastics |
ASTM E 1753 : 2001 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
ASTM D 4226 : 2005 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
ASTM E 84 : 2023 : REV C | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 2244 : 2015 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 4756 : 2002 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
ASTM E 1753 : 1995 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
ASTM D 5206 : 1996 : R2002 : EDT 1 | Standard Test Method for Windload Resistance of Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 5947 : 2002 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
ASTM D 883 : 2024 | Standard Terminology Relating to Plastics |
ASTM E 1753 : 2019 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
ASTM D 2244 : 2023 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 4756 : 2013 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
ASTM D 2244 : 2011 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 2457 : 2008 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
ASTM D 4226 : 2019 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
ASTM D 7793 : 2020 | Standard Specification for Insulated Vinyl Siding |
ASTM D 3892 : 1993 : R2003 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 3892 : 2015 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 2244 : 2009 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 5206 : 2019 | Standard Test Method for Windload Resistance of Rigid Plastic Siding |
ASTM D 4756 : 1996 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
ASTM D 1042 : 2006 | Standard Test Method for Linear Dimensional Changes of Plastics Under Accelerated Service Conditions |
ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
ASTM D 7209 : 2006 | Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015) |
ASTM D 5947 : 2011 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
ASTM D 5947 : 2018 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
ASTM D 2244 : 2002 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 2244 : 2016 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 3892 : 1993 : R1998 | Standard Practice for Packaging/Packing of Plastics |
ASTM E 84 : 2023 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 3679 : 2003 : EDT 2 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 3679 : 2008 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 1042 : 2022 | Standard Test Method for Linear Dimensional Changes of Plastics Caused by Exposure to Heat and Moisture |
ASTM E 1753 : 2018 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
ASTM D 7793 : 2017 | Standard Specification for Insulated Vinyl Siding |
ASTM D 7793 : 2016 | Standard Specification for Insulated Vinyl Siding |
ASTM D 4756 : 2015 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 2244 : 2015 : EDT 1 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 2244 : 2009 : REV B | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 1042 : 1993 | Standard Test Method for Linear Dimensional Changes of Plastics Under Accelerated Service Conditions |
ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 2244 : 2002 : EDT 1 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM E 84 : 2021 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 3679 : 2001 : REV B | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 2244 : 2015 : REV A | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM E 84 : 2022 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM E 1753 : 2022 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
ASTM E 1753 : 2018 : REV A | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
ASTM D 3679 : 2002 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 3679 : 2009 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 1435 : 1994 | Standard Practice for Outdoor Weathering of Plastics |
ASTM D 3679 : 2004 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 635 : 2022 | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position |
ASTM E 1753 : 2013 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
ASTM D 5947 : 2006 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
ASTM D 1042 : 2001 : REV A | Standard Test Method for Linear Dimensional Changes of Plastics Under Accelerated Service Conditions |
ASTM D 2457 : 2013 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
ASTM E 84 : 2020 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 5206 : 2006 : REV A | Standard Test Method for Windload Resistance of Rigid Plastic Siding |
ASTM D 2244 : 2014 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM E 84 : 2021 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 3679 : 2004 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 7793 : 2024 | Standard Specification for Insulated Vinyl Siding |
ASTM D 3679 : 2009 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 2244 : 2005 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 1042 : 2012 : R2017 | Standard Test Method for Linear Dimensional Changes of Plastics Caused by Exposure to Heat and Moisture |
ASTM D 4756 : 2003 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
ASTM D 3679 : 2017 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 5206 : 2024 | Standard Test Method for Windload Resistance of Rigid Plastic Siding |
ASTM D 3679 : 2013 | Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Siding |
ASTM D 4226 : 2010 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
ASTM D 3679 : 2011 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 1435 : 2005 | Standard Practice for Outdoor Weathering of Plastics |
ASTM D 3679 : 1999 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
ASTM D 2457 : 1997 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
ASTM D 3679 : 2003 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 7793 : 2012 | Standard Specification for Insulated Vinyl Siding |
ASTM D 7793 : 2013 | Standard Specification for Insulated Vinyl Siding |
ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
ASTM D 2244 : 2007 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 5947 : 2003 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
ASTM D 1042 : 2001 | Standard Test Method for Linear Dimensional Changes of Plastics Under Accelerated Service Conditions |
ASTM D 4226 : 2016 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
ASTM D 3679 : 2021 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 3679 : 2004 : REV A : EDT 1 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 5947 : 2001 : EDT 1 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
ASTM D 2244 : 2022 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 4756 : 2015 : R2021 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit (Withdrawn 2023) |
ASTM E 84 : 2023 : REV B | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 3679 : 2005 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 3679 : 2024 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 7793 : 2021 | Standard Specification for Insulated Vinyl Siding |
ASTM D 3679 : 2002 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 4756 : 2002 : REV A | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
ASTM D 5206 : 1996 | Standard Test Method for Windload Resistance of Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 3892 : 1993 : R2009 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 4226 : 2000 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
ASTM D 5206 : 2013 | Standard Test Method for Windload Resistance of Rigid Plastic Siding |
ASTM E 84 : 2023 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 4756 : 2006 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
ASTM D 2457 : 2003 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
ASTM D 2244 : 2009 : REV A | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 2244 : 1993 : R2000 | Standard Test Method for Calculation of Color Differences From Instrumentally Measured Color Coordinates |
ASTM D 3679 : 2001 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 3679 : 2003 : EDT 1 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM E 1753 : 2004 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
ASTM D 2457 : 2021 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
ASTM D 2457 : 2008 : EDT 1 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
ASTM D 3679 : 2001 : REV C | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
ASTM D 1042 : 2012 | Standard Test Method for Linear Dimensional Changes of Plastics Caused by Exposure to Heat and Moisture |
ASTM D 4226 : 2009 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
ASTM D 3679 : 2001 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 1435 : 1999 | Standard Practice for Outdoor Weathering of Plastics |
ASTM D 4226 : 2011 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
ASTM D 3679 : 2006 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.