• Shopping Cart
    There are no items in your cart

ASTM E 1030/E1030M : 2015 : REDLINE

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Practice for Radiographic Examination of Metallic Castings

Available format(s)

PDF

Superseded date

03-07-2021

Language(s)

English

Published date

01-12-2015

€74.48
Excluding VAT

CONTAINED IN VOL. 03.03, 2017 Gives a uniform procedure for radiographic examination of metallic castings using radiographic film as the recording medium.

Committee
E 07
DevelopmentNote
Supersedes ASTM E 1030. (01/2016)
DocumentType
Redline
Pages
20
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This practice2 provides a uniform procedure for radiographic examination of metallic castings using radiographic film as the recording medium.

1.2This standard addresses the achievement of, or protocols for achieving, common or practical levels of radiographic coverage for castings, to detect primarily volumetric discontinuities to sensitivity levels measured by nominated image quality indicators. All departures, including alternate means or methods to increase coverage, or address challenges of detecting non-volumetric planar-type discontinuities, shall be agreed upon between the purchaser and supplier and shall consider Appendix X1 and Appendix X2.

1.3The radiographic techniques stated herein provide adequate assurance for defect detectability; however, it is recognized that, for special applications, specific techniques using more or less stringent requirements may be required than those specified. In these cases, the use of alternate radiographic techniques shall be as agreed upon between purchaser and supplier (also see Section 5).

1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM E 1254 : 2013 Standard Guide for Storage of Radiographs and Unexposed Industrial Radiographic Films
ASTM E 689 : 2015 : REDLINE Standard Reference Radiographs for Ductile Iron Castings
ASTM E 446 : 2015 : REDLINE Standard Reference Radiographs for Steel Castings Up to 2 in. (50.8 mm) in Thickness
ASNT SNT TC 1A : 2016 TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL
ASTM E 186 : 2015 : REDLINE Standard Reference Radiographs for Heavy-Walled (2 to 4<fraction><num>1</num><den>2</den></fraction > in. (50.8 to 114 mm)) Steel Castings
ASTM E 802 : 2015 : REDLINE Standard Reference Radiographs for Gray Iron Castings Up to 4<fraction><num>1</num><den>2</den> </fraction> in. (114 mm) in Thickness
ISO 9712:2012 Non-destructive testing Qualification and certification of NDT personnel
NAS410:2003 NAS CERTIFICATION & QUALIFICATION OF NONDESTRUCTIVE TEST PERSONNEL
ASTM E 155 : 2015 : REDLINE Standard Reference Radiographs for Inspection of Aluminum and Magnesium Castings
ASTM E 505 : 2015 : REDLINE Standard Reference Radiographs for Inspection of Aluminum and Magnesium Die Castings
ISO 5579:2013 Non-destructive testing — Radiographic testing of metallic materials using film and X- or gamma rays — Basic rules
ASNT CP 189 : 2016 QUALIFICATION AND CERTIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL
ASTM E 1320 : 2015 : REDLINE Standard Reference Radiographs for Titanium Castings
ASTM E 192 : 2015 : REDLINE Standard Reference Radiographs of Investment Steel Castings for Aerospace Applications
ASTM E 999 : 2015 : REDLINE Standard Guide for Controlling the Quality of Industrial Radiographic Film Processing
ASTM E 272 : 2015 : REDLINE Standard Reference Radiographs for High-Strength Copper-Base and Nickel-Copper Alloy Castings
ASTM E 280 : 2015 : REDLINE Standard Reference Radiographs for Heavy-Walled (4<fraction><num>1</num><den>2</den></fraction > to 12 in. (114 to 305 mm)) Steel Castings
ASTM E 543 : 2015 : REDLINE Standard Specification for Agencies Performing Nondestructive Testing
ASTM E 1079 : 2016 : REDLINE Standard Practice for Calibration of Transmission Densitometers
ASTM E 310 : 2015 : REDLINE Standard Reference Radiographs for Tin Bronze Castings

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.