Skip to content
Please enter a keyword to search

  • ASTM E 168 : 2016

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Standard Practices for General Techniques of Infrared Quantitative Analysis

    Available format(s):  Hardcopy, PDF

    Superseded date:  13-01-2023

    Language(s):  English

    Published date:  07-06-2016

    Publisher:  American Society for Testing and Materials

    Add To Cart

    Abstract - (Show below) - (Hide below)

    CONTAINED IN VOL. 03.06, 2016 Defines the techniques most often used in infrared quantitative analysis.

    Scope - (Show below) - (Hide below)

    1.1These practices cover the techniques most often used in infrared quantitative analysis. Practices associated with the collection and analysis of data on a computer are included as well as practices that do not use a computer.

    1.2This practice does not purport to address all of the concerns associated with developing a new quantitative method. It is the responsibility of the developer to ensure that the results of the method fall in the desired range of precision and bias.

    1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

    1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements appear in Section 6, Note A4.7, Note A4.11, and Note A5.6.

    General Product Information - (Show below) - (Hide below)

    Committee E 13
    Document Type Standard Practice
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM E 1944 : 1998 : R2013 Standard Practice for Describing and Measuring Performance of Laboratory Fourier Transform Near-Infrared (FT-NIR) Spectrometers: Level Zero and Level One Tests
    CSA S807 : 2010 SPECIFICATION FOR FIBRE-REINFORCED POLYMERS
    ASTM D 3133 : 2001 Standard Test Method for Quantitative Determination of Cellulose Nitrate in Alkyd Modified Lacquers by Infrared Spectrophotometry
    ASTM E 169 : 2016 : REDLINE Standard Practices for General Techniques of Ultraviolet-Visible Quantitative Analysis
    ASTM E 60 : 2011 Standard Practice for Analysis of Metals, Ores, and Related Materials by Spectrophotometry
    MIL-A-27420 Base Document:1970 AIR, LIQUID, FOR BREATHING PURPOSES
    ASTM E 131 : 2010 : R2015 Standard Terminology Relating to Molecular Spectroscopy
    BS ISO 15063:2011 Plastics. Polyols for use in the production of polyurethanes. Determination of hydroxyl number by NIR spectroscopy
    ASTM D 2124 : 1999 : R2011 Standard Test Method for Analysis of Components in Poly(Vinyl Chloride) Compounds Using an Infrared Spectrophotometric Technique (Withdrawn 2020)
    MIL PRF 002104 : L LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, COMBAT/TACTICAL SERVICE
    ASTM E 2412 : 2010 Standard Practice for Condition Monitoring of Used Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry
    ASTM D 3921 : 1996 : R2011 Standard Test Method for Oil and Grease and Petroleum Hydrocarbons in Water (Withdrawn 2013)
    MIL-PRF-32177 Revision A:2012 CLEANING COMPOUND, NONSKID
    ASTM D 7678 : 2017 : REDLINE Standard Test Method for Total Oil and Grease (TOG) and Total Petroleum Hydrocarbons (TPH) in Water and Wastewater with Solvent Extraction using Mid-IR Laser Spectroscopy
    ASTM E 1944 : 1998 : R2002 Standard Practice for Describing and Measuring Performance of Laboratory Fourier Transform Near-Infrared (FT-NIR) Spectrometers: Level Zero and Level One Tests
    ASTM E 2106 : 2000 : R2011 Standard Practice for General Techniques of Liquid Chromatography-Infrared (LC/IR) and Size Exclusion Chromatography-Infrared (SEC/IR) Analyses
    SAE AMS 3961/3 : 2015 350 DEGREES F AUTOCLAVE CURE, LOW FLOW TOUGHENED EPOXY PREPREGS, TYPE 35, CLASS 1, GRADE 190, FIBER 1
    ASTM D 5594 : 1998 : R2004 Standard Test Method for Determination of the Vinyl Acetate Content of Ethylene-Vinyl Acetate (EVA) Copolymers by Fourier Transform Infrared Spectroscopy (FT-IR)
    ASTM D 7418 : 2012 : REDLINE Standard Practice for Set-Up and Operation of Fourier Transform Infrared (FT-IR) Spectrometers for In-Service Oil Condition Monitoring
    ASTM E 1865 : 1997 : R2007 Standard Guide for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air
    ASTM E 932 : 1989 : R2007 Standard Practice for Describing and Measuring Performance of Dispersive Infrared Spectrometers
    ASTM E 1252 : 1998 Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis
    ASTM D 6342 : 2012 : R2017 : EDT 1 Standard Practice for Polyurethane Raw Materials: Determining Hydroxyl Number of Polyols by Near Infrared (NIR) Spectroscopy
    ASTM D 3089 : 1997 : R2008 Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes
    ASTM E 3045 : 2016 Standard Practice for Crack Detection Using Vibroacoustic Thermography
    ASTM D 3594 : 1993 : R2000 Standard Test Method for Copolymerized Ethyl Acrylate In Ethylene-Ethyl Acrylate Copolymers
    ASTM D 7806 : 2012 Standard Test Method for Determination of the Fatty Acid Methyl Ester (FAME) Content of a Blend of Biodiesel and Petroleum-Based Diesel Fuel Oil Using Mid-Infrared Spectroscopy
    ASTM D 7588 : 2011 Standard Guide for FT-IR Fingerprinting of a Non-Aqueous Liquid Paint as Supplied in the Manufacturer's Container
    ASTM E 1865:1997 Standard Guide for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air
    ASTM E 334 : 2001 : R2013 Standard Practice for General Techniques of Infrared Microanalysis
    ASTM F 1630 : 2000 Standard Test Method for Low Temperature FT-IR Analysis of Single Crystal Silicon for III-V Impurities (Withdrawn 2003)
    ASTM E 131 : 2010 Standard Terminology Relating to Molecular Spectroscopy
    ASTM D 5594 : 1998 Standard Test Method for Determination of the Vinyl Acetate Content of Ethylene-Vinyl Acetate (EVA) Copolymers by Fourier Transform Infrared Spectroscopy (FT-IR)
    ASTM E 1252 : 1998 : R2007 Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis
    ASTM E 204 : 1998 Standard Practices for Identification of Material by Infrared Absorption Spectroscopy, Using the ASTM Coded Band and Chemical Classification Index
    ASTM D 5477 : 2011 Standard Practice for Identification of Polymer Layers or Inclusions by Fourier Transform Infrared Microspectroscopy (FT-IR)
    MIL-P-46144 Revision C:1986 PLASTIC SHEET, POLYCARBONATE
    MIL-C-47221 Revision A:1982 COMPOUND, MOLDING, EPOXY RESIN, SILICON DIOXIDE AND ASBESTOS FIBER FILL
    CSA S808 : 2014 SPECIFICATION FOR FIBRE-REINFORCED POLYMER (FRP) MATERIALS FOR EXTERNALLY REINFORCING STRUCTURES
    ASTM D 7575 : 2011 Standard Test Method for Solvent-Free Membrane Recoverable Oil and Grease by Infrared Determination
    ASTM D 2238 : 1992 : R1999 Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm
    DWA-M 143-20:2018 TEST METHOD FOR DROP IMPACT RESISTANCE OF BLOW-MOLDED THERMOPLASTIC CONTAINERS
    ASTM E 334:2001 Standard Practice for General Techniques of Infrared Microanalysis
    CSA S807 : 2010 : R2015 SPECIFICATION FOR FIBRE-REINFORCED POLYMERS
    MIL-PRF-85570 Revision E:2012 CLEANING COMPOUNDS, AIRCRAFT, EXTERIOR
    ASTM D 2702 : 2005 : R2016 Standard Practice for Rubber Chemicals—Determination of Infrared Absorption Characteristics
    SAE AMS 3961/1 : 2015 350 DEGREES F AUTOCLAVE CURE, LOW FLOW TOUGHENED EPOXY PREPREGS, TYPE 38, CLASS 2, GRADE 193, STYLE 3K-70-PW, FIBER 1
    ASTM E 1865 : 1997 : R2013 Standard Guide for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air
    ASTM D 2238 : 1992 : R2004 Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm
    ASTM E 1642 : 2000 : R2005 Standard Practice for General Techniques of Gas Chromatography Infrared (GC/IR) Analysis
    ASTM D 8111 : 2017 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine
    ASTM E 2105 : 2000 : R2016 Standard Practice for General Techniques of Thermogravimetric Analysis (TGA) Coupled With Infrared Analysis (TGA/IR)
    ASTM E 573 : 2001 : R2013 Standard Practices for Internal Reflection Spectroscopy
    ASTM D 6342 : 20121 Standard Practice for Polyurethane Raw Materials: Determining Hydroxyl Number of Polyols by Near Infrared (NIR) Spectroscopy
    ASTM E 1944 : 1998 : R2007 Standard Practice for Describing and Measuring Performance of Laboratory Fourier Transform Near-Infrared (FT-NIR) Spectrometers: Level Zero and Level One Tests
    ASTM E 932 : 1989 : R2013 Standard Practice for Describing and Measuring Performance of Dispersive Infrared Spectrometers
    ASTM E 2106 : 2000 : R2006 Standard Practice for General Techniques of Liquid Chromatography-Infrared (LC/IR) and Size Exclusion Chromatography-Infrared (SEC/IR) Analyses
    ASTM D 3594 : 1993 : R2006 Standard Test Method for Copolymerized Ethyl Acrylate In Ethylene-Ethyl Acrylate Copolymers
    ASTM D 2124 : 1999 : R2004 Standard Test Method for Analysis of Components in Poly(Vinyl Chloride) Compounds Using an Infrared Spectrophotometric Technique
    ASTM D 2124 : 1999 : EDT 1 Standard Test Method for Analysis of Components in Poly(Vinyl Chloride) Compounds Using an Infrared Spectrophotometric Technique
    ASTM D 6277 : 2007 : R2012 Standard Test Method for Determination of Benzene in Spark-Ignition Engine Fuels Using Mid Infrared Spectroscopy
    ASTM D 7371 : 2014 : REDLINE Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Esters) Content in Diesel Fuel Oil Using Mid Infrared Spectroscopy (FTIR-ATR-PLS Method)
    ASTM E 2106:2000 Standard Practice for General Techniques of Liquid Chromatography-Infrared (LC/IR) and Size Exclusion Chromatography-Infrared (SEC/IR) Analyses
    ASTM F 561 : 2013 Standard Practice for Retrieval and Analysis of Medical Devices, and Associated Tissues and Fluids
    ASTM D 345 : 2002 Side bearings of the freight wagon bogies. General specifications
    ASTM F 1864 : 2021 Standard Test Method for Dust Erosion Resistance of Optical and Infrared Transparent Materials and Coatings
    ASTM D 6277 : 2007 : R2022 Standard Test Method for Determination of Benzene in Spark-Ignition Engine Fuels Using Mid Infrared Spectroscopy
    ASTM E 1865 : 1997 : R2021 Standard Guide for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air
    ASTM D 3124 : 1998 : R2019 Standard Test Method for Vinylidene Unsaturation in Polyethylene by Infrared Spectrophotometry
    ASTM D 3288/D3288M : 2020 Standard Test Methods for Magnet-Wire Enamels
    ASTM E 2106 : 2000 : R2019 Standard Practice for General Techniques of Liquid Chromatography-Infrared (LC/IR) and Size Exclusion Chromatography-Infrared (SEC/IR) Analyses
    ASTM D 7806 : 2020 Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Ester) and Triglyceride Content in Diesel Fuel Oil Using Mid-Infrared Spectroscopy (FTIR Transmission Method)
    ASTM D 6348 : 2012 : R2020 Standard Test Method for Determination of Gaseous Compounds by Extractive Direct Interface Fourier Transform Infrared (FTIR) Spectroscopy
    ASTM E 573 : 2001 : R2021 Standard Practices for Internal Reflection Spectroscopy
    ASTM D 6047 : 2017 : R2021 Standard Test Methods for Rubber, Raw—Determination of 5-Ethylidenenorbornene (ENB) or Dicyclopentadiene (DCPD) in Ethylene-Propylene-Diene (EPDM) Terpolymers
    ASTM D 7399 : 2018 Standard Test Method for Determination of the Amount of Polypropylene in Polypropylene/Low Density Polyethylene Mixtures Using Infrared Spectrophotometry
    ASTM D 3677 : 2010 : R2019 Standard Test Methods for Rubber—Identification by Infrared Spectrophotometry
    ASTM E 1982 : 1998 : R2021 Standard Practice for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air
    ASTM D 6645 : 2018 Standard Test Method for Methyl (Comonomer) Content in Polyethylene by Infrared Spectrophotometry
    ASTM D 7678 : 2017 : R2022 Standard Test Method for Total Oil and Grease (TOG) and Total Petroleum Hydrocarbons (TPH) in Water and Wastewater with Solvent Extraction using Mid-IR Laser Spectroscopy
    ASTM D 2238 : 2022 Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm−1
    ASTM D 2144 : 2007 : R2021 Standard Practices for Examination of Electrical Insulating Oils by Infrared Absorption
    ASTM E 1944 : 1998 : R2021 Standard Practice for Describing and Measuring Performance of Laboratory Fourier Transform Near-Infrared (FT-NIR) Spectrometers: Level Zero and Level One Tests
    ASTM D 5576 : 2000 : R2021 : EDT 1 Standard Practice for Determination of Structural Features in Polyolefins and Polyolefin Copolymers by Infrared Spectrophotometry (FT-IR)
    ASTM D 7588 : 2011 : R2018 Standard Guide for FT-IR Fingerprinting of a Non-Aqueous Liquid Paint as Supplied in the Manufacturer's Container
    ASTM D 3900 : 2017 : R2021 Standard Test Methods for Rubber—Determination of Ethylene Units in Ethylene-Propylene Copolymers (EPM) and in Ethylene-Propylene-Diene Terpolymers (EPDM) by Infrared Spectrometry
    ASTM E 169 : 2016 : R2022 Standard Practices for General Techniques of Ultraviolet-Visible Quantitative Analysis
    ASTM D 6342 : 2022 Standard Practice for Polyurethane Raw Materials: Determining Hydroxyl Number of Polyols by Near Infrared (NIR) Spectroscopy
    ASTM D 2702 : 2005 : R2021 Standard Practice for Rubber Chemicals—Determination of Infrared Absorption Characteristics
    ASTM E 275 : 2008 : R2022 Standard Practice for Describing and Measuring Performance of Ultraviolet and Visible Spectrophotometers
    ASTM D 7418 : 2022 Standard Practice for Set-Up and Operation of Fourier Transform Infrared (FT-IR) Spectrometers for In-Service Oil Condition Monitoring
    ASTM E 60 : 2011 : R2022 : EDT 1 Standard Practice for Analysis of Metals, Ores, and Related Materials by Spectrophotometry
    ASTM E 3045 : 2022 Standard Practice for Crack Detection Using Vibroacoustic Thermography
    ASTM D 5594 : 2018 : REV A Standard Test Method for Determination of the Vinyl Acetate Content of Ethylene-Vinyl Acetate (EVA) Copolymers by Fourier Transform Infrared Spectroscopy (FT-IR)
    ASTM D 7861 : 2014 : R2019 Standard Test Method for Determination of Fatty Acid Methyl Esters (FAME) in Diesel Fuel by Linear Variable Filter (LVF) Array Based Mid-Infrared Spectroscopy
    ASTM D 7889 : 2021 Standard Test Method for Field Determination of In-Service Fluid Properties Using IR Spectroscopy
    ASTM D 5477 : 2018 Standard Practice for Identification of Polymer Layers or Inclusions by Fourier Transform Infrared Microspectroscopy (FT-IR)
    ASTM D 8350 : 2022 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IVB Spark-Ignition Engine
    ASTM D 8074 : 2022 Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine
    ASTM D 6248 : 2021 Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry
    ASTM D 8193 : 2018 Standard Test Method for Total Oil and Grease (TOG) and Total Petroleum Hydrocarbon (TPH) in Water and Wastewater with Solvent Extraction Using Non-Dispersive Mid-IR Transmission Spectroscopy
    ASTM D 7371 : 2014 : R2022 Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Esters) Content in Diesel Fuel Oil Using Mid Infrared Spectroscopy (FTIR-ATR-PLS Method)
    ASTM D 8111 : 2022 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine
    ASTM D 3594 : 1993 Standard Test Method for Copolymerized Ethyl Acrylate In Ethylene-Ethyl Acrylate Copolymers
    ASTM E 1982: 1998 Standard Practice for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air
    ASTM E 2105 : 2000 : R2010 Standard Practice for General Techniques of Thermogravimetric Analysis (TGA) Coupled With Infrared Analysis (TGA/IR)
    MIL-P-48296 Base Document:1974 POLYTETRAFLUOROETHYLENE (PTFE)
    ASTM D 6645 : 2001 Standard Test Method for Methyl (Comonomer) Content in Polyethylene by Infrared Spectrophotometry
    ASTM E 1982 : 1998 : R2007 Standard Practice for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air
    ASTM E 1865 : 1997 : R2002 Standard Guide for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air
    ASTM D 7399 : 2008 Standard Test Method for Determination of the Amount of Polypropylene (PP) in Polypropylene/LDPE Mixtures Using Infrared Spectrophotometer (FTIR) (Withdrawn 2017)
    ASTM E 1982 : 1998 : R2013 Standard Practice for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air
    ASTM D 3921 : 1996 Standard Test Method for Oil and Grease and Petroleum Hydrocarbons in Water
    ASTM D 2702 : 2005 Standard Practice for Rubber Chemicals-Determination of Infrared Absorption Characteristics
    ASTM D 2144 : 2007 : R2013 Standard Practices for Examination of Electrical Insulating Oils by Infrared Absorption
    ASTM F 121 : 1983 : EDT 1 Test Method for Interstitial Atomic Oxygen Content of Silicon by Infrared Absorption (Withdrawn 1989)
    ASTM D 3288 : 2003 Standard Test Methods for Magnet-Wire Enamels
    MIL D 48561 : A
    MIL-A-70604 Base Document:1988 AMINE BONDING AGENT
    ASTM D 3124 : 1998 : R2003 Standard Test Method for Vinylidene Unsaturation in Polyethylene by Infrared Spectrophotometry
    GOST R 52714:2018 Motor gasolines. Determination of individual and group hydrocarbon composition by capillary gas сhromatography method
    ASTM D 3414 : 1998 : R2011 : EDT 1 Standard Test Method for Comparison of Waterborne Petroleum Oils by Infrared Spectroscopy (Withdrawn 2018)
    ASTM D 3124 : 1998 Standard Test Method for Vinylidene Unsaturation in Polyethylene by Infrared Spectrophotometry
    SAE AMS 3961/2 : 2015 350 DEGREES F AUTOCLAVE CURE, LOW FLOW TOUGHENED EPOXY PREPREGS, TYPE 35, CLASS 1, GRADE 190, FIBER 2
    ASTM D 3133 : 2001 : R2005 Standard Test Method for Quantitative Determination of Cellulose Nitrate in Alkyd Modified Lacquers by Infrared Spectrophotometry (Withdrawn 2008)
    SAE AMS 3960 : 2015 Advanced Composites Prepreg - Nominal 250 °F Cure - Carbon Fiber and Epoxy Resin, Unidirectional Tape
    ASTM D 3414 : 1998 : R2004 Standard Test Method for Comparison of Waterborne Petroleum Oils by Infrared Spectroscopy
    ASTM E 1655 : 2017 : REDLINE Standard Practices for Infrared Multivariate Quantitative Analysis
    ASTM F 120 : 1988 Practices for Determination of the Concentration of Impurities in Single Crystal Semiconductor Materials by Infrared Absorption Spectroscopy (Withdrawn 1993)
    ASTM E 2105 : 2000 : R2005 Standard Practice for General Techniques of Thermogravimetric Analysis (TGA) Coupled With Infrared Analysis (TGA/IR)
    ASTM E 1642 : 2000 Standard Practice for General Techniques of Gas Chromatography Infrared (GC/IR) Analysis
    ASTM D 6277 : 2007 Standard Test Method for Determination of Benzene in Spark-Ignition Engine Fuels Using Mid Infrared Spectroscopy
    ASTM D 5576 : 2000 : R2013 Standard Practice for Determination of Structural Features in Polyolefins and Polyolefin Copolymers by Infrared Spectrophotometry (FT-IR)
    ASTM D 7861 : 2014 : EDT 1 Standard Test Method for Determination of Fatty Acid Methyl Esters (FAME) in Diesel Fuel by Linear Variable Filter (LVF) Array Based Mid-Infrared Spectroscopy
    ASTM D 7861 : 2014 Standard Test Method for Determination of Fatty Acid Methyl Esters (FAME) in Diesel Fuel by Linear Variable Filter (LVF) Array Based Mid-Infrared Spectroscopy
    ASTM E 204 : 1998 : R2007 Standard Practices for Identification of Material by Infrared Absorption Spectroscopy, Using the ASTM Coded Band and Chemical Classification Index (Withdrawn 2014)
    ASTM E 932 : 1989 : R2002 Standard Practice for Describing and Measuring Performance of Dispersive Infrared Spectrometers
    ASTM D 6248 : 1998 : R2012 : EDT 1 Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry (Withdrawn 2021)
    ASTM E 573 : 2001 Standard Practices for Internal Reflection Spectroscopy
    ASTM D 6248 : 1998 : R2004 Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry
    SAE AMS C 22587 : 1999 CARTRIDGES, GREASE, 14 OUNCE (FOR CARTRIDGE-TYPE GREASE GUN)
    MIL-M-48767 Base Document:1975 Methyl Formate (For Use In Ammunition)
    ASTM E 932 : 1989 : R1997 Standard Practice for Describing and Measuring Performance of Dispersive Infrared Spectrometers
    ASTM D 6248 : 1998 Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry
    MIL-E-48225 Base Document:1973 ETHYLENE GLYCOL DINITRATE (EGDN)
    ASTM D 5576:2000 Standard Practice for Determination of Structural Features in Polyolefins and Polyolefin Copolymers by Infrared Spectroscopy (FT-IR)
    ASTM D 3414 : 1998 Standard Test Method for Comparison of Waterborne Petroleum Oils by Infrared Spectroscopy
    ASTM E 1252 : 1998 : R2002 Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis
    ADS-13F-HDBK : 1997 AERONAUTICAL DESIGN STANDARD - HANDBOOK - AIR VEHICLE MATERIALS AND PROCESSES
    ASTM D 5594 : 1998 : R2012 Standard Test Method for Determination of the Vinyl Acetate Content of Ethylene-Vinyl Acetate (EVA) Copolymers by Fourier Transform Infrared Spectroscopy (FT-IR)
    SAE AMS P 46144 : 2015 PLASTIC SHEET, POLYCARBONATE
    ASTM D 7066 : 2004 : R2017 Standard Test Method for dimer/trimer of chlorotrifluoroethylene (S-316) Recoverable Oil and Grease and Nonpolar Material by Infrared Determination
    ASTM D 7066 : 2004 : EDT 1 Standard Test Method for dimer/trimer of chlorotrifluoroethylene (S-316) Recoverable Oil and Grease and Nonpolar Material by Infrared Determination
    ASTM E 1642 : 2000 : R2010 Standard Practice for General Techniques of Gas Chromatography Infrared (GC/IR) Analysis
    ISO 15063:2011 Plastics Polyols for use in the production of polyurethanes Determination of hydroxyl number by NIR spectroscopy
    ASTM D 3124 : 1998 : R2011 Standard Test Method for Vinylidene Unsaturation in Polyethylene by Infrared Spectrophotometry
    ASTM D 7889 : 2013 Standard Test Method for Field Determination of In-Service Fluid Properties Using IR Spectroscopy
    ASTM E 1944:1998 Standard Practice for Describing and Measuring Performance of Laboratory Fourier Transform Near-Infrared (FT-NIR) Spectrometers: Level Zero and Level One Tests
    ASTM D 6645 : 2001 : R2010 Standard Test Method for Methyl (Comonomer) Content in Polyethylene by Infrared Spectrophotometry
    ASTM E 573 : 2001 : R2007 Standard Practices for Internal Reflection Spectroscopy
    ASTM E 1252 : 1998 : R2013 : EDT 1 Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis
    ASTM E 1982 : 1998 : R2002 Standard Practice for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air
    ASTM F 1864 : 2016 : REDLINE Standard Test Method for Dust Erosion Resistance of Optical and Infrared Transparent Materials and Coatings
    ASTM D 2702 : 2005 : R2011 Standard Practice for Rubber Chemicals—Determination of Infrared Absorption Characteristics
    SAE AMS 3915 : 2015 ADVANCED COMPOSITES PREPREG - NOMINAL 250 DEGREES F CURE - GLASS FIBER AND EPOXY RESIN, 7781 WEAVE FABRIC
    ASTM D 7066 : 2004 : R2011 Standard Test Method for dimer/trimer of chlorotrifluoroethylene (S-316) Recoverable Oil and Grease and Nonpolar Material by Infrared Determination
    ASTM D 3900 : 2017 : REDLINE Standard Test Methods for Rubber—Determination of Ethylene Units in Ethylene-Propylene Copolymers (EPM) and in Ethylene-Propylene-Diene Terpolymers (EPDM) by Infrared Spectrometry
    ASTM D 7066 : 2004 Standard Test Method for dimer/trimer of chlorotrifluoroethylene (S-316) Recoverable Oil and Grease and Nonpolar Material by Infrared Determination
    ASTM D 3677 : 2010 : EDT 1 Standard Test Methods for RubberIdentification by Infrared Spectrophotometry
    MIL-T-70681 Base Document:1988 TRIPHENYL BISMUTH
    SAE AMS 3961 : 2015 350 DEGREES F AUTOCLAVE CURE, LOW FLOW TOUGHENED EPOXY PREPREGS
    MIL-M-70605 Base Document:1988 2,2'-METHYLENEBIS (4-METHYL-6-TERT-BUTYLPHENOL)
    ASTM D 3288/D3288M : 2015 : REDLINE Standard Test Methods for Magnet-Wire Enamels
    ASTM D 3594 : 1993 : R2013 Standard Test Method for Copolymerized Ethyl Acrylate In Ethylene-Ethyl Acrylate Copolymers (Withdrawn 2019)
    SAE AMS 3909 : 2014 CLOTH, ARAMID, INTERMEDIATE MODULUS
    SAE AMS 3914A : 2015 ADVANCED COMPOSITES PREPREG - NOMINAL 250 DEGREES F CURE - 12K TOW CARBON FIBER AND EPOXY RESIN, PLAIN WEAVE FABRIC
    ASTM E 60 : 2011 : R2016 Standard Practice for Analysis of Metals, Ores, and Related Materials by Spectrophotometry
    ASTM E 275 : 2008 Describing and Measuring Performance of Ultraviolet and Visible Spectrophotometers
    ASTM D 2238 : 1992 : R2012 : EDT 1 Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm−1 (Withdrawn 2021)
    ASTM D 3677 : 2010 : R2015 Standard Test Methods for Rubber—Identification by Infrared Spectrophotometry
    ASTM E 2105 : 2000 Standard Practice for General Techniques of Thermogravimetric Analysis (TGA) Coupled With Infrared Analysis (TGA/IR)
    ASTM D 2144 : 2007 Standard Practices for Examination of Electrical Insulating Oils by Infrared Absorption
    ASTM D 3921 : 1996 : R2003 : EDT 1 Standard Test Method for Oil and Grease and Petroleum Hydrocarbons in Water
    ASTM E 334 : 2001 : R2007 Standard Practice for General Techniques of Infrared Microanalysis
    ASTM E 204 : 1998 : R2002 Standard Practices for Identification of Material by Infrared Absorption Spectroscopy, Using the ASTM Coded Band and Chemical Classification Index
    ASTM D 8074 : 2016 Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine
    ASTM E 1642 : 2000 : R2016 Standard Practice for General Techniques of Gas Chromatography Infrared (GC/IR) Analysis
    ASTM D 3677 : 2010 Standard Test Methods for Rubber--Identification by Infrared Spectrophotometry
    ASTM D 7575 : 2011 : R2017 Standard Test Method for Solvent-Free Membrane Recoverable Oil and Grease by Infrared Determination
    ASTM D 5576 : 2000 : R2006 Standard Practice for Determination of Structural Features in Polyolefins and Polyolefin Copolymers by Infrared Spectrophotometry (FT-IR)
    ASTM F 1109 : 1987 Specification for Porous Composites of Polytetrafluoroethylene and Carbon for Surgical Implant Applications (Withdrawn 1993)
    ASTM E 2412 : 2010 : R2018 Standard Practice for Condition Monitoring of In-Service Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry
    ASTM D 6047 : 2017 : REDLINE Standard Test Methods for Rubber, Raw—Determination of 5-Ethylidenenorbornene (ENB) or Dicyclopentadiene (DCPD) in Ethylene-Propylene-Diene (EPDM) Terpolymers
    SAE AMS6562:2023 Medium Temperature, Out-of-Autoclave, Oven-Vacuum-Bag Cure Epoxy Resin Impregnated Fiber Reinforced Composite Materials

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM E 1421 : 1999 : R2021 Standard Practice for Describing and Measuring Performance of Fourier Transform Mid-Infrared (FT-MIR) Spectrometers: Level Zero and Level One Tests
    ASTM E 1421 : 1999 : R2004 Standard Practice for Describing and Measuring Performance of Fourier Transform Mid-Infrared (FT-MIR) Spectrometers: Level Zero and Level One Tests
    ASTM E 1252 : 1998 : R2007 Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis
    ASTM E 1252 : 1998 Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis
    ASTM E 932 : 1989 : R2013 Standard Practice for Describing and Measuring Performance of Dispersive Infrared Spectrometers
    ASTM E 1655 : 2004 Standard Practices for Infrared Multivariate Quantitative Analysis
    ASTM E 1421 : 1999 : R2009 Standard Practice for Describing and Measuring Performance of Fourier Transform Mid-Infrared (FT-MIR) Spectrometers: Level Zero and Level One Tests
    ASTM E 1421 : 1999 : R2015 : EDT 1 Standard Practice for Describing and Measuring Performance of Fourier Transform Mid-Infrared (FT-MIR) Spectrometers: Level Zero and Level One Tests
    ASTM E 932 : 1989 : R2021 Standard Practice for Describing and Measuring Performance of Dispersive Infrared Spectrometers
    ASTM E 1252 : 1998 : R2021 Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis
    ASTM E 1421 : 1999 Standard Practice for Describing and Measuring Performance of Fourier Transform Mid-Infrared (FT-MIR) Spectrometers Level Zero and Level One Tests
    ASTM E 334 : 2001 : R2021 Standard Practice for General Techniques of Infrared Microanalysis
    ASTM E 1655 : 2017 Standard Practices for Infrared Multivariate Quantitative Analysis
    ASTM E 1655 : 2000 Standard Practices for Infrared Multivariate Quantitative Analysis
    ASTM E 1655 : 2005 Standard Practices for Infrared Multivariate Quantitative Analysis
    ASTM E 334 : 2001 : R2013 Standard Practice for General Techniques of Infrared Microanalysis
    ASTM E 1655 : 2005 : R2012 Standard Practices for Infrared Multivariate Quantitative Analysis
    ASTM E 1252 : 1998 : R2013 : EDT 1 Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis
    ASTM E 1252 : 1998 : R2002 Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective