ASTM G 21 : 2015 : R2021 : EDT 1
Current
The latest, up-to-date edition.
Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi
Hardcopy , PDF
English
22-06-2021
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
G 03
|
| DocumentType |
Standard Practice
|
| Pages |
6
|
| ProductNote |
ε1NOTE—Editorial corrections were made to the footnote in5.1.1and to6.4.1in June 2021.
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This practice covers determination of the effect of fungi on the properties of synthetic polymeric materials in the form of molded and fabricated articles, tubes, rods, sheets, and film materials. Changes in optical, mechanical, and electrical properties may be determined by the applicable ASTM methods.
1.2The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 1705/C1705M : 2009 : R2016 | Standard Specification for Structural Cementitious Panels |
| ASTM C 1534 : 2020 : REV A | Standard Specification for Flexible Polymeric Foam Sheet Insulation Used as a Thermal and Sound Absorbing Liner for Duct Systems |
| ASTM E 3152 : 2018 | Standard Guide for Standard Test Methods and Practices Available for Determining Antifungal Activity on Natural or Synthetic Substrates Treated with Antimicrobial Agents |
| ASTM E 2180 : 2018 | Standard Test Method for Determining the Activity of Incorporated Antimicrobial Agent(s) In Polymeric or Hydrophobic Materials |
| ASTM C 1325 : 2019 | Standard Specification for Fiber-Mat Reinforced Cementitious Backer Units |
| ASTM D 6947/D6947M : 2016 | Standard Specification for Liquid Applied Moisture Cured Polyurethane Coating Used in Spray Polyurethane Foam Roofing System |
| ASTM D 6754/D6754M : 2015 | Standard Specification for Ketone Ethylene Ester Based Sheet Roofing |
| ASTM C 647 : 2019 | Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation |
| ASTM E 1925 : 2018 | Specification for Engineering and Design Criteria for Rigid Wall Relocatable Structures |
| ASTM F 104 : 2011 : R2020 | Standard Classification System for Nonmetallic Gasket Materials |
| ASTM C 1822 : 2021 | Standard Specification for Insulating Covers on Accessible Lavatory Piping |
| ASTM D 4300 : 2001 : R2021 : EDT 1 | Standard Test Methods for Ability of Adhesive Films to Support or Resist the Growth of Fungi |
| ASTM D 3105 : 2017 | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
| ASTM C 1071 : 2019 | Standard Specification for Fibrous Glass Duct Lining Insulation (Thermal and Sound Absorbing Material) |
| ASTM D 5590 : 2017 | Standard Test Method for Determining the Resistance of Paint Films and Related Coatings to Fungal Defacement by Accelerated Four-Week Agar Plate Assay |
| ASTM D 6083/D6083M : 2021 | Standard Specification for Liquid-Applied Acrylic Coating Used in Roofing |
| ASTM C 1288 : 2017 | Standard Specification for Fiber-Cement Interior Substrate Sheets |
| ASTM E 1514 : 1998 : R2017 : EDT 1 | Standard Specification for Structural Standing Seam Steel Roof Panel Systems |
| ASTM F 793/F793M : 2020 | Standard Classification of Wall Coverings by Use Characteristics |
| ASTM E 1637 : 1998 : R2017 : EDT 1 | Standard Specification for Structural Standing Seam Aluminum Roof Panel Systems |
| ASTM C 318/C318M : 2013 : R2018 | Standard Specification for Gypsum Formboard |
| ASTM D 495 : 2014 | Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation |
| ASTM D 150 : 2022 | Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation |
| ASTM E 96/E96M : 2022 : REV A : EDT 1 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM E 96/E96M : 2022 : REV A | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM E 96/E96M : 2021 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM E 96/E96M : 2022 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM E 96/E96M : 2023 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM E 96/E96M : 2024 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM E 96/E96M : 2016 | Standard Test Methods for Water Vapor Transmission of Materials |
| ASTM D 638 : 2014 | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
| ASTM E 308 : 2018 | Standard Practice for Computing the Colors of Objects by Using the CIE System |
| ASTM D 785 : 2008 : R2015 | Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials |
| ASTM D 785 : 2023 | Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials |
| ASTM E 308 : 2022 | Standard Practice for Computing the Colors of Objects by Using the CIE System |
| ASTM D 150 : 2018 | Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation |
| ASTM D 495 : 2022 | Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation |
| ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 638 : 2022 | Standard Test Method for Tensile Properties of Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.