BS EN 1401-1:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastic piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U) Specifications for pipes, fittings and the system
Hardcopy , PDF
23-07-2019
English
31-10-2009
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
3.1 Terms and definitions
3.2 Symbols
3.3 Abbreviations
4 Material
4.1 Raw material
4.2 Pipe material
4.3 Fitting material
4.4 Utilisation of non-virgin materials
4.5 Sealing ring retaining means
5 General characteristics
5.1 Appearance
5.2 Colour
6 Geometrical characteristics
6.1 General
6.2 Dimensions of pipes
6.3 Dimensions of fittings
6.4 Dimensions of sockets and spigots
6.5 Types of fittings
7 Mechanical characteristics
7.1 Mechanical characteristics of pipes
7.2 Mechanical characteristics of fittings
8 Physical characteristics
8.1 Physical characteristics of pipes
8.2 Physical characteristics of fittings
9 Performance requirements
10 Sealing rings
11 Adhesives
12 Marking
12.1 General
12.2 Minimum required marking of pipes
12.3 Minimum required marking of fittings
12.4 Additional marking
Annex A (normative) - Utilisation of non-virgin material
A.1 Material definitions
A.2 Own reprocessable material
A.3 External reprocessable and recyclable materials
with agreed specification
A.4 External reprocessable and recyclable materials
not covered by an agreed specification
A.5 Summary of use of non-virgin material
Annex B (informative) - General characteristics of PVC-U
pipes and fittings
B.1 General
B.2 Compound characteristics
B.3 Ring stiffness
B.4 Creep ratio
B.5 Chemical resistance
B.6 Abrasion resistance
B.7 Hydraulic roughness
B.8 Diametric deflection
Annex C (informative) - Product standards
Bibliography
Describes the requirements for solid wall pipes, fittings and the system of unplasticized poly(vinyl chloride) (PVC-U) piping systems in the field of non-pressure underground drainage and sewerage: a) outside the building structure (application area code "U"); and b) both buried in ground within the building structure (application area code "D") and outside the building.
| Committee |
PRI/88
|
| DevelopmentNote |
Supersedes BS 4660(1989), 94/340645 DC, 94/340646 DC, 94/340647 DC and 94/340648 DC. (09/2005) Supersedes 06/30148365 DC. (07/2009)
|
| DocumentType |
Standard
|
| Pages |
42
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NF EN 1401-1 : 2009 | Identical |
| NS EN 1401-1 : 2009 | Identical |
| NEN EN 1401-1 : 2009 | Identical |
| DIN EN 1401-1:2009-07 | Identical |
| UNI EN 1401-1 : 2009 | Identical |
| EN 1401-1:2009 | Identical |
| UNE-EN 1401-1:2009 | Identical |
| SN EN 1401-1 : 2009 | Identical |
| I.S. EN 1401-1:2009 | Identical |
| NBN EN 1401-1 : 2009 | Identical |
| ONORM EN 1401-1 : 2009 | Identical |
| 08/30142158 DC : DRAFT NOV 2008 | BS 5834-2 - SURFACE BOXES, GUARDS AND UNDERGROUND CHAMBERS FOR GAS AND UTILITIES' PURPOSES - PART 2: SPECIFICATION FOR SURFACE BOXES |
| BS 6297(2007) : 2007 | CODE OF PRACTICE FOR THE DESIGN AND INSTALLATION OF DRAINAGE FIELDS FOR USE IN WASTEWATER TREATMENT |
| BS 8004:2015 | Code of practice for foundations |
| 07/30138205 DC : DRAFT MAR 2007 | BS 6297 - DESIGN AND INSTALLATION OF SMALL SEWAGE TREATMENT WORKS AND CESSPOOLS - CODE OF PRACTICE |
| 15/30301520 DC : 0 | BS 8004 - CODE OF PRACTICE FOR FOUNDATIONS (FORMERLY CP 2004) |
| BS 6349-1:2000 | Maritime structures Code of practice for general criteria |
| BS 7158:2001 | Plastics inspection chambers for drains and sewers. Specification |
| BS 4660:2000 | Thermoplastics ancillary fittings of nominal sizes 110 and 160 for below ground gravity drainage and sewerage |
| EN 1277:2003 | Plastics piping systems - Thermoplastics piping systems for buried non-pressure applications - Test methods for leaktightness of elastomeric sealing ring type joints |
| EN 295-3:2012 | Vitrified clay pipe systems for drains and sewers - Part 3: Test methods |
| ISO 580:2005 | Plastics piping and ducting systems — Injection-moulded thermoplastics fittings — Methods for visually assessing the effects of heating |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| ISO/TR 10358:1993 | Plastics pipes and fittings Combined chemical-resistance classification table |
| ENV 1401-3:2001 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Guidance for installation |
| EN 1411:1996 | Plastics piping and ducting systems - Thermoplastics pipes - Determination of resistance to external blows by the staircase method |
| EN ISO 9967:2016 | Thermoplastics pipes - Determination of creep ratio (ISO 9967:2016) |
| ISO 265-1:1988 | Pipes and fittings of plastics materials Fittings for domestic and industrial waste pipes Basic dimensions: Metric series Part 1: Unplasticized poly(vinyl chloride) (PVC-U) |
| EN 1055:1996 | Plastics piping systems - Thermoplastics piping systems for soil and waste discharge inside buildings - Test method for resistance to elevated temperature cycling |
| ISO/TR 7620:2005 | Rubber materials — Chemical resistance |
| EN ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
| CEN/TS 15223:2017 | Plastics piping systems - Validated design parameters of buried thermoplastics piping systems |
| EN 12061:1999 | Plastics piping systems - Thermoplastics fittings - Test method for impact resistance |
| EN 922:1994 | Plastics piping and ducting systems - Pipes and fittings of unplasticized poly(vinyl chloride) (PVC-U) - Specimen preparation for determination of the viscosity number and calculation of the K-value |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| EN 476:2011 | General requirements for components used in drains and sewers |
| ISO 472:2013 | Plastics — Vocabulary |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 14758-1:2012 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system |
| EN 727:1994 | Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST) |
| ISO 18373-1:2007 | Rigid PVC pipes Differential scanning calorimetry (DSC) method Part 1: Measurement of the processing temperature |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| EN 12666-1:2005+A1:2011 | Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system |
| EN ISO 9969:2016 | Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016) |
| EN 744:1995 | Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock method |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN ISO 580:2005 | Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO 580:2005) |
| EN 580:2003 | Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for the resistance to dichloromethane at a specified temperature (DCMT) |
| ISO 9967:2016 | Thermoplastics pipes Determination of creep ratio |
| EN 1905:1998 | Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material - Method for assessment of the PVC content based on total chlorine content |
| EN 1053:1995 | Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test method for watertightness |
| EN ISO 2505:2005 | Thermoplastics pipes - Longitudinal reversion - Test method and parameters (ISO 2505:2005) |
| ISO 13967:2009 | Thermoplastics fittings Determination of ring stiffness |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| ISO 9969:2016 | Thermoplastics pipes Determination of ring stiffness |
| EN 12256:1998 | Plastics piping systems - Thermoplastics fittings - Test method for mechanical strength or flexibility of fabricated fittings |
| EN ISO 472:2013 | Plastics - Vocabulary (ISO 472:2013) |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
| ISO 2505:2005 | Thermoplastics pipes — Longitudinal reversion — Test method and parameters |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.