• BS EN 60384-1 : 2016

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION

    Available format(s):  Hardcopy, PDF

    Superseded date:  04-10-2021

    Language(s):  English

    Published date:  01-01-2016

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 General
    2 Technical data
    3 Quality assessment procedures
    4 Tests and measurement procedures
    Annex A (informative) - Interpretation of sampling plans
            and procedures as described in IEC 60410 for use within
            quality assessment systems
    Annex B (informative) - Rules for the preparation of detail
            specifications for capacitors and resistors for electronic
            equipment for use within quality assessment systems
    Annex C (informative) - Layout of the first page of a PCP/CQC
            specification
    Annex D (informative) - Requirements for capability approval
            test report
    Annex E (informative) - Guide for pulse testing of capacitors
    Annex F (informative) - Guidance for the extension of endurance
            tests on fixed capacitors
    Annex G (normative) - Damp heat, steady state with voltage
            applied, for metallized film capacitors only
    Annex H (normative) - Accelerated damp heat, steady state,
            for multilayer ceramic capacitors only
    Annex Q (informative) - Quality assessment procedures
    Bibliography
    Annex ZA (normative) - Normative references to international
             publications with their corresponding European publications

    Abstract - (Show below) - (Hide below)

    Defines standard terms, inspection procedures and methods 000 of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose.

    General Product Information - (Show below) - (Hide below)

    Committee EPL/40X
    Development Note Supersedes BS EN 130000 (08/2001) Supersedes 97/207202 DC (10/2005) Supersedes BS 6201-1(1982), BS QC300000(1983), BS QC300100(1991) & 06/30149145 DC. (03/2010) Supersedes 14/30280850 DC. (10/2016)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60068-2-82:2007 Environmental testing - Part 2-82: Tests - Test XW1: Whisker test methods for electronic and electric components
    IEC 60384-3-1:2006 Fixed capacitors for use in electronic equipment - Part 3-1: Blank detail specification: Surface mount fixed tantalum electrolytic capacitors with manganese dioxide solid electrolyte - Assessment level EZ
    IEC 61193-2:2007 Quality assessment systems - Part 2: Selection and use of sampling plans for inspection of electronic components and packages
    EN 60294 : 2012 MEASUREMENT OF THE DIMENSIONS OF A CYLINDRICAL COMPONENT WITH AXIAL TERMINATIONS (IEC 60294:2012)
    IEC 60384-2:2011 Fixed capacitors for use in electronic equipment - Part 2: Sectional specification - Fixed metallized polyethylene terephthalate film dielectric d.c. capacitors
    EN ISO 80000-1 : 2013 QUANTITIES AND UNITS - PART 1: GENERAL (ISO 80000-1:2009 + COR 1:2011)
    IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
    IEC 60068-2-58:2015+AMD1:2017 CSV Environmental testing - Part 2-58: Tests - Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD)
    IEC 60068-2-27:2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
    IEC 60068-2-20:2008 Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
    EN 60068-2-20 : 2008 ENVIRONMENTAL TESTING - PART 2-20: TESTS - TEST T: TEST METHODS FOR SOLDERABILITY AND RESISTANCE TO SOLDERING HEAT OF DEVICES WITH LEADS
    EN 60068-2-1:2007 ENVIRONMENTAL TESTING - PART 2-1: TESTS - TEST A: COLD
    IEC 61249-2-7:2002 MATERIALS FOR PRINTED BOARDS AND OTHER INTERCONNECTING STRUCTURES - PART 2-7: REINFORCED BASE MATERIALS CLAD AND UNCLAD - EPOXIDE WOVEN E-GLASS LAMINATED SHEET OF DEFINED FLAMMABILITY (VERTICAL BURNING TEST), COPPER-CLAD
    EN 60068-2-2:2007 ENVIRONMENTAL TESTING - PART 2-2: TESTS - TEST B: DRY HEAT
    IEC 60469:2013 Transitions, pulses and related waveforms - Terms, definitions and algorithms
    IEC 60068-2-21:2006 Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
    IEC 60068-2-13:1983 ENVIRONMENTAL TESTING - PART 2: TESTS - TEST M: LOW AIR PRESSURE
    EN 60068-1:2014 ENVIRONMENTAL TESTING - PART 1: GENERAL AND GUIDANCE (IEC 60068-1:2013)
    ISO 3:1973 Preferred numbers Series of preferred numbers
    EN 61249-2-7:2002/corrigendum:2005 MATERIALS FOR PRINTED BOARDS AND OTHER INTERCONNECTING STRUCTURES - PART 2-7: REINFORCED BASE MATERIALS CLAD AND UNCLAD - EPOXIDE WOVEN E-GLASS LAMINATED SHEET OF DEFINED FLAMMABILITY (VERTICAL BURNING TEST), COPPER-CLAD
    IEC 60068-2-67:1995 ENVIRONMENTAL TESTING - PART 2: TESTS - TEST CY: DAMP HEAT, STEADY STATE, ACCELERATED TEST PRIMARILY INTENDED FOR COMPONENTS
    EN 60717 : 2012 METHOD FOR THE DETERMINATION OF THE SPACE REQUIRED BY CAPACITORS AND RESISTORS WITH UNIDIRECTIONAL TERMINATIONS (IEC 60717:2012)
    IEC 60410:1973 Sampling plans and procedures for inspection by attributes
    EN 60068-2-27:2009 ENVIRONMENTAL TESTING - PART 2-27: TESTS - TEST EA AND GUIDANCE: SHOCK
    IEC 60294:2012 MEASUREMENT OF THE DIMENSIONS OF A CYLINDRICAL COMPONENT WITH AXIAL TERMINATIONS
    IEC 60384-3:2016 Fixed capacitors for use in electronic equipment - Part 3: Sectional specification - Surface mount fixed tantalum electrolytic capacitors with solid (MnO2) electrolyte
    IEC 60068-2-54:2006 Environmental testing - Part 2-54: Tests - Test Ta: Solderability testing of electronic components by the wetting balance method
    IEC 60384-3-101:1995 Fixed capacitors for use in electronic equipment - Part 3-101: Detail specification: Fixed tantalum chip capacitors for surface mounting with solid electrolyte and porous anode, style I. Assessment level E
    EN 60068-2-17 : 1994 BASIC ENVIRONMENTAL TESTING - TEST Q: SEALING
    IEC 60068-2-17:1994 Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing
    EN 61193-2 : 2007 QUALITY ASSESSMENT SYSTEMS - PART 2: SELECTION AND USE OF SAMPLING PLANS FOR INSPECTION OF ELECTRONIC COMPONENTS AND PACKAGES
    EN 60068-2-21:2006 ENVIRONMENTAL TESTING - PART 2-21: TESTS - TEST U: ROBUSTNESS OF TERMINATIONS AND INTEGRAL MOUNTING DEVICES
    IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
    EN 60068-2-67 : 1996 ENVIRONMENTAL TESTING - TESTS - TEST CY: DAMP HEAT, STEADY STATE, ACCELERATED TEST PRIMARILY INTENDED FOR COMPONENTS
    IEC 60062:2016 Marking codes for resistors and capacitors
    EN 60062:2016/AC:2016-12 MARKING CODES FOR RESISTORS AND CAPACITORS (IEC 60062:2016/COR1:2016)
    ISO 80000-1:2009 Quantities and units Part 1: General
    EN 60063 : 2015 Preferred number series for resistors and capacitors
    EN 60068-2-78:2013 ENVIRONMENTAL TESTING - PART 2-78: TESTS - TEST CAB: DAMP HEAT, STEADY STATE (IEC 60068-2-78:2012)
    EN 60068-2-13 : 1999 ENVIRONMENTAL TESTING - PART 2: TESTS - TEST M: LOW AIR PRESSURE
    EN 60068-2-6:2008 ENVIRONMENTAL TESTING - PART 2-6: TESTS - TEST FC: VIBRATION (SINUSOIDAL)
    IEC 60063:2015 PREFERRED NUMBER SERIES FOR RESISTORS AND CAPACITORS
    ISO 9000:2015 Quality management systems Fundamentals and vocabulary
    EN 60068-2-82:2007 Environmental testing - Part 2-82: Tests - Test XW1: Whisker test methods for electronic and electric components
    IEC 60717:2012 METHOD FOR THE DETERMINATION OF THE SPACE REQUIRED BY CAPACITORS AND RESISTORS WITH UNIDIRECTIONAL TERMINATIONS
    EN 60068-2-54 : 2006 ENVIRONMENTAL TESTING - PART 2-54: TESTS - TEST TA: SOLDERABILITY TESTING OF ELECTRONIC COMPONENTS BY THE WETTING BALANCE METHOD
    IEC 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
    EN 60068-2-30:2005 ENVIRONMENTAL TESTING - PART 2-30: TESTS - TEST DB: DAMP HEAT, CYCLIC (12 H + 12 H CYCLE)
    EN 60695-11-5:2017 FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE (IEC 60695-11-5:2016)
    IEC 60695-11-5 : 2.0 FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE
    IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
    EN 60068-2-45:1992/A1:1993 Environmental testing - Part 2: Tests - Test Xa and guidance: Immersion in cleaning solvents
    EN 60068-2-14:2009 ENVIRONMENTAL TESTING - PART 2-14: TESTS - TEST N: CHANGE OF TEMPERATURE
    IEC 60384-26:2010 Fixed capacitors for use in electronic equipment - Part 26: Sectional specification - Fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte
    IEC 60068-2-69:2017 Environmental testing - Part 2-69: Tests - Test Te/Tc: Solderability testing of electronic components and printed boards by the wetting balance (force measurement) method
    IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective