• Shopping Cart
    There are no items in your cart

BS EN 61969-1:2012

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Mechanical structures for electronic equipment. Outdoor enclosures Design guidelines

Available format(s)

Hardcopy , PDF

Superseded date

09-07-2020

Superseded by

BS EN IEC 61969-1:2020

Language(s)

English

Published date

29-02-2012

€165.94
Excluding VAT

INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Dimensions
5 Environmental requirements and tests, safety aspects
6 Electromagnetic shielding
7 Thermal management and acoustic noise suppression
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

Gives an overview of specifications for enclosures focused on requirements for outdoor applications for stationary use at non-weather protected locations.

Committee
EPL/48
DevelopmentNote
Supersedes 97/231605 DC (05/2005) Supersedes 09/30202438 DC. (03/2012)
DocumentType
Standard
Pages
16
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

This part of IEC 61969 contains design guidelines for outdoor enclosures and is applicable over a wide field of mechanical, electromechanical and electronic equipment and its installation where a modular design is used. The objective of this standard is to provide an overview of specifications for enclosures focused on requirements for outdoor applications for stationary use at non-weather protected locations. These enclosures are considered to contain any equipment and provide protection for the outdoor installed facilities against unwanted environmental impacts. The installed equipment may be, but is not limited to, subracks according to IEC 60917-2-2 or IEC 60297-3-101. A typical outdoor enclosure is shown in Figure 1.

Standards Relationship
NBN EN 61969-1 : 2012 Identical
EN 61969-1:2012 Identical
DIN EN 61969-1 : 2012 Identical
IEC 61969-1:2011 Identical
NF EN 61969-1 : 2012 Identical
I.S. EN 61969-1:2012 Identical
SN EN 61969-1 : 2000 Identical
UNE-EN 61969-1:2001 Identical

EN 62262:2002 Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)
IEC 60297-3-101:2004 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-101: Subracks and associated plug-in units
EN 61439-5:2015/AC:2015 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 5: ASSEMBLIES FOR POWER DISTRIBUTION IN PUBLIC NETWORKS (IEC 61439-5:2014)
EN 61587-2:2011 MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - TESTS FOR IEC 60917 AND IEC 60297 - PART 2: SEISMIC TESTS FOR CABINETS AND RACKS (IEC 61587-2:2011)
EN 60825-1:2014/AC:2017-06 SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014)
EN 62305-4:2011/AC:2016 PROTECTION AGAINST LIGHTNING - PART 4: ELECTRICAL AND ELECTRONIC SYSTEMS WITHIN STRUCTURES (IEC 62305-4:2010)
IEC 61587-2:2011 Mechanical structures for electronic equipment - Tests for IEC 60917 and 60297 - Part 2: Seismic tests for cabinets and racks
IEC 61587-3:2013 Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 3: Electromagnetic shielding performance tests for cabinets and subracks
ETS 300 200019-1-4 : 20001 EQUIPMENT ENGINEERING (EE); ENVIRONMENTAL CONDITIONS AND ENVIRONMENTAL TESTS FOR TELECOMMUNICATIONS EQUIPMENT - CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - STATIONARY USE AT NON-WEATHERPROTECTED LOCATIONS
IEC 61587-1:2016 Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation
IEC 60825-1:2014 Safety of laser products - Part 1: Equipment classification and requirements
EN 60297-3-101:2004 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-101: Subracks and associated plug-in units
EN 61587-1:2017 Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation
EN 61587-3:2013 Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 3: Electromagnetic shielding performance tests for cabinets and subracks
EN 62194:2005 Method of evaluating the thermal performance of enclosures
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN ISO 1518-1:2011 Paints and varnishes - Determination of scratch resistance - Part 1: Constant-loading method (ISO 1518-1:2011)
IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
EN ISO 7779:2010 Acoustics - Measurement of airborne noise emitted by information technology and telecommunications equipment (ISO 7779:2010)
IEC 62262:2002 Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)
IEC 61439-5:2014 Low-voltage switchgear and controlgear assemblies - Part 5: Assemblies for power distribution in public networks
ISO 1518-1:2011 Paints and varnishes Determination of scratch resistance Part 1: Constant-loading method
IEC 62305-4:2010 Protection against lightning - Part 4: Electrical and electronic systems within structures
EN 61140:2016 Protection against electric shock - Common aspects for installation and equipment
EN 61010-1:2010 Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements
IEC 61140:2016 Protection against electric shock - Common aspects for installation and equipment
ISO 3864:1984 Safety colours and safety signs
IEC 61010-1:2010+AMD1:2016 CSV Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements
IEC 60050-581:2008 International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment
ISO 7779:2010 Acoustics Measurement of airborne noise emitted by information technology and telecommunications equipment
IEC 62194:2005 Method of evaluating the thermal performance of enclosures
ETS 300 753 : 20001 EQUIPMENT ENGINEERING (EE); ACOUSTIC NOISE EMITTED BY TELECOMMUNICATIONS EQUIPMENT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.