BS EN ISO 14693:2003

Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviated terms
   3.1 Terms and definitions
   3.2 Abbreviated terms
4 Design
   4.1 Design conditions
   4.2 Strength analysis
   4.3 Size class designation
   4.4 Rating
   4.5 Load rating basis
   4.6 Design safety factor
   4.7 Shear strength
   4.8 Specific equipment
   4.9 Design documentation
5 Design verification
   5.1 General
   5.2 Design verification function test
   5.3 Design verification pressure test
   5.4 Design verification load test
   5.5 Determination of rated load
   5.6 Alternative design verification test procedure and rating
   5.7 Design verification load-testing apparatus
   5.8 Design changes
   5.9 Records
6 Materials requirements
   6.1 General
   6.2 Written specifications
   6.3 Mechanical properties
   6.4 Material qualification
   6.5 Manufacture
   6.6 Chemical composition
7 Welding requirements
   7.1 General
   7.2 Welding qualification
   7.3 Written documentation
   7.4 Control of consumables
   7.5 Weld properties
   7.6 Post-weld heat treatment
   7.7 Quality control requirements
   7.8 Specific requirements - Fabrication welds
   7.9 Specific requirements - Repair welds
8 Quality control
   8.1 General
   8.2 Quality control personnel qualifications
   8.3 Measuring and test equipment
   8.4 Quality control for specific equipment and components
   8.5 Dimensional verification
   8.6 Proof load testing
   8.7 Hydrostatic testing
   8.8 Functional testing
9 Equipment
   9.1 General
   9.2 Rotary tables
   9.3 Rotary bushings
   9.4 Rotary slips
   9.5 Spiders not capable of use as elevators
   9.6 Safety clamps not used as a hoisting device
   9.7 Manual tongs
   9.8 Power tongs
   9.9 Drawworks components
   9.10 Rotary hose
   9.11 Piston mud-pump components
   9.12 Antifriction bearings
10 Marking
   10.1 Product marking
   10.2 Marking method
11 Documentation
   11.1 Record retention
   11.2 Documentation to be kept by the manufacturer
   11.3 Documentation to be delivered with the equipment
Annex A (normative) Supplementary requirements
      A.1 Introduction
      A.2 SR1 - Proof load testing
      A.3 SR2 - Low-temperature testing
      A.4 SR2A - Additional low-temperature testing
      A.5 SR3 - Data book
      A.6 SR4 - Additional volumetric examination of castings
      A.7 SR5 - Volumetric examination of wrought material
Annex B (informative) Guidance for qualification of heat-treatment
        equipment
      B.1 Temperature tolerance
      B.2 Furnace calibration
      B.3 Instruments
Annex C (informative) Drilling machinery component dimensions
        expressed in US customary units
Annex D (informative) Recommended piston mud-pump nomenclature
        and maintenance
      D.1 Piston mud-pump nomenclature
      D.2 Old designs
      D.3 Types
      D.4 Designation
Bibliography

Gives general principles and specifies requirements for design, manufacture and testing of new drilling and well-servicing equipment and of replacement primary load-carrying components manufactured subsequent to the publication of ISO 14693:2003.

This International Standard provides general principles and specifies requirements for design, manufacture and testing of new drilling and well-servicing equipment and of replacement primary load-carrying components manufactured subsequent to the publication of this International Standard. This International Standard is applicable to the following equipment: rotary tables; rotary bushings; rotary slips; rotary hoses; piston mud-pump components; drawworks components; spiders not capable of use as elevators; manual tongs; safety clamps not used as hoisting devices; power tongs, including spinning wrenches. AnnexA gives a number of standardized supplementary requirements which apply only when specified.