BS EN ISO 14978:2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Geometrical Product Specifications (GPS). General concepts and requirements for GPS measuring equipment
Hardcopy , PDF
25-03-2019
English
30-06-2008
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Abbreviations
5 Design characteristics
5.1 General
5.2 Indicating measuring equipment
5.3 Material measures
6 Metrological characteristics
6.1 General
6.2 Identification, definition and choice of metrological
characteristics
6.3 Indicating measuring equipment - identification of
general metrological characteristics
6.4 Material measures - Identification of general
metrological characteristics
7 Types of presentation and types of specifications for
characteristics
7.1 General
7.2 Presentation of characteristic curves - Fixed and
floating zero
7.3 Presentation of a characteristic - Statistical
7.4 Specifications for single-value metrological
characteristics
7.5 Specification for metrological characteristics
defined in a range
7.6 Specification for metrological characteristics defined
in a two- or three-dimensional range
8 Calibration of metrological characteristics
8.1 Manufacturer and supplier of measuring instruments
8.2 User of measuring instruments
8.3 Measurement uncertainty
9 Marking
Annex A (normative) General minimum requirements and
guidance for clauses in GPS standards for
specific measuring equipment
Annex B (informative) Data sheet for measuring equipment
requirements
Annex C (normative) Relation to the GPS matrix model
Bibliography
Describes the general requirements, terms and definitions of characteristics of simple GPS measuring equipment, e.g. micrometers, dial gauges, callipers, surface plates, height gauges, gauge blocks, but not necessarily excluding more complicated equipment.
| Committee |
TPR/1
|
| DocumentType |
Standard
|
| Pages |
46
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NEN EN ISO 14978 : 2006 C1 2008 | Identical |
| UNI EN ISO 14978 : 2006 | Identical |
| NF EN ISO 14978 : 2006 | Identical |
| SN EN ISO 14978 : 2006 CORR 2008 | Identical |
| UNE-EN ISO 14978:2007 | Identical |
| NS EN ISO 14978 : 2006 AC 2008 | Identical |
| ONORM EN ISO 14978 : 2008 | Identical |
| ISO 14978:2006 | Identical |
| I.S. EN ISO 14978:2006 | Identical |
| NBN EN ISO 14978 : 2006 COR 2008 | Identical |
| DIN EN ISO 14978:2006-09 | Identical |
| BS 8888:2008 | Technical product specification. Specification |
| ISO/TR 14638:1995 | Geometrical product specification (GPS) Masterplan |
| ISO/TS 17450-2:2002 | Geometrical product specifications (GPS) General concepts Part 2: Basic tenets, specifications, operators and uncertainties |
| ISO 12179:2000 | Geometrical Product Specifications (GPS) Surface texture: Profile method Calibration of contact (stylus) instruments |
| ISO 5459:2011 | Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems |
| ISO/TS 14253-2:1999 | Geometrical Product Specifications (GPS) Inspection by measurement of workpieces and measuring equipment Part 2: Guide to the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification |
| ISO 2692:2014 | Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 1:2016 | Geometrical product specifications (GPS) Standard reference temperature for the specification of geometrical and dimensional properties |
| ISO 14253-1:2017 | Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications |
| ISO 8062-3:2007 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings |
| ISO 3650:1998 | Geometrical Product Specifications (GPS) Length standards Gauge blocks |
| ISO/TR 16015:2003 | Geometrical product specifications (GPS) — Systematic errors and contributions to measurement uncertainty of length measurement due to thermal influences |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.