BS EN ISO 17078-2:2007
Current
The latest, up-to-date edition.
Petroleum and natural gas industries. Drilling and production equipment Flow-control devices for side-pocket mandrels
Hardcopy , PDF
English
31-01-2010
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
4.1 Abbreviations
4.2 Symbols and engineering terms
5 Functional specification
5.1 General
5.2 Functional characteristics
5.3 Well parameters
5.4 Operational parameters
5.5 Compatibility with well-related equipment
5.6 Environmental service classes
5.7 Design validation grades
5.8 Product functional testing grades
5.9 Quality control grades
5.10 Additional required testing
6 Technical specification
6.1 General requirements
6.2 Technical characteristics
6.3 Design criteria
6.4 Allowable design changes
6.5 Design verification and validation requirements
6.6 Product functional testing requirements
7 Supplier/manufacturer requirements
7.1 General
7.2 Documentation and data control
7.3 Product identification requirements
7.4 Quality control requirements
7.5 Heat-treating-equipment qualification
7.6 Welding requirements
7.7 Non-destructive examination requirements
7.8 Storage and shipping preparation
7.9 Allowable changes after manufacturing
7.10 Reconditioning of flow-control devices
Annex A (normative) - Design validation and product
functional testing requirements
Annex B (normative) - Environmental service classes
Annex C (normative) - Design validation grades
Annex D (normative) - Product functional testing grades
Annex E (normative) - Interface testing requirements
Annex F (normative) - Insertion testing requirements
Annex G (normative) - Probe and travel testing and load
rate determination
Annex H (normative) - Dynamic flow testing and flow
coefficient calculation
Annex I (normative) - Back-check testing
Annex J (normative) - Opening and closing pressure testing
Annex K (normative) - Bellows actuation life cycle testing
Annex L (normative) - Erosion testing requirements
Annex M (normative) - Shelf (bellows integrity) testing
requirements for nitrogen-pressure-charged
flow-control devices
Annex N (normative) - Conducting port/seat leakage rate testing
Annex O (informative) - Performance testing - Recommendations
for a flow-control device performance
test facility
Annex P (informative) - Performance testing - Prediction
correlations using a simplified flow
control device performance model
Bibliography
Specifies requirements for subsurface flow-control devices used in side-pocket mandrels (hereafter called flow-control devices) intended for use in the worldwide petroleum and natural gas industry.
| Committee |
PSE/17/-/4
|
| DevelopmentNote |
Supersedes 05/30132215 DC. (01/2008)
|
| DocumentType |
Standard
|
| Pages |
136
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NF EN ISO 17078-2 : 2009 | Identical |
| ISO 17078-2:2007 | Identical |
| NEN EN ISO 17078-2 : 2008 C1 2009 | Identical |
| DIN EN ISO 17078-2:2010-08 | Identical |
| I.S. EN ISO 17078-2:2007 | Identical |
| NS EN ISO 17078-2 : 2007 AC 2009 | Identical |
| EN ISO 17078-2:2007 | Equivalent |
| ISO 17078-2:2007/Cor 1:2009 | Identical |
| EN ISO 17078-2:2007/AC:2009 | Identical |
| ISO 80000-4:2006 | Quantities and units — Part 4: Mechanics |
| ISO 6506-1:2014 | Metallic materials — Brinell hardness test — Part 1: Test method |
| ASNT SNT TC 1A : 2016 | TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL |
| ASME PV CODE 9 : 2017 | BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS |
| ISO 9712:2012 | Non-destructive testing — Qualification and certification of NDT personnel |
| ASME PV CODE 8 DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1 |
| ISO 6508-1:2016 | Metallic materials — Rockwell hardness test — Part 1: Test method |
| ISO 14313:2007 | Petroleum and natural gas industries — Pipeline transportation systems — Pipeline valves |
| ASME B31.8 : 2016 | Gas Transmission and Distribution Piping Systems |
| ISO 6892:1998 | Metallic materials — Tensile testing at ambient temperature |
| API 14A : 2015 | SPECIFICATION FOR SUBSURFACE SAFETY VALVE EQUIPMENT |
| SAE AS568D | Aerospace Size Standard for O-rings |
| MIL-STD-1916 Base Document:1996 | DOD Preferred Methods for Acceptance of Product |
| NACE MR 01 75 : 2003 | METALS FOR SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING RESISTANCE IN SOUR OILFIELD ENVIRONMENTS |
| ISO 31-0:1992 | Quantities and units — Part 0: General principles |
| ANSI/NCSL Z540 1 : 94(R2002) | CALIBRATION - CALIBRATION LABORATORIES AND MEASURING AND TEST EQUIPMENT - GENERAL REQUIREMENTS |
| ASME B1.20.1 : 2013(R2018) | PIPE THREADS, GENERAL PURPOSE (INCH) |
| API MPMS CH14.2 : 2ED 1994(R2012) | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 14.2: COMPRESSIBILITY FACTORS OF NATURAL GAS AND OTHER RELATED HYDROCARBON GASES |
| AGA REPORT 8 : 92 REPRINT 94 | COMPRESSIBILITY AND SUPERCOMPRESSIBILITY FOR NATURAL GAS AND OTHER HYDROCARBON GASES TRANSMISSION MEASUREMENT |
| ISO 17078-3:2009 | Petroleum and natural gas industries — Drilling and production equipment — Part 3: Running tools, pulling tools and kick-over tools and latches for side-pocket mandrels |
| API 6D :2015 | SPECIFICATION FOR PIPELINE AND PIPING VALVES |
| ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| ASME B16.34 : 2017 | VALVES - FLANGED, THREADED, AND WELDING END |
| ASME PV CODE 5 : 2017 | BOILER AND PRESSURE VESSEL CODE - NONDESTRUCTIVE EXAMINATION |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| ISO 10432:2004 | Petroleum and natural gas industries — Downhole equipment — Subsurface safety valve equipment |
| BS 2M 54:1991 | Specification for temperature control in the heat treatment of metals |
| ISO 17078-1:2004 | Petroleum and natural gas industries — Drilling and production equipment — Part 1: Side-pocket mandrels |
| MIL-STD-413 Revision C:1980 | Visual Inspection Guide for Elastomeric O-Rings (See Notice 2 for Replacement Information) |
| ISO 11960:2014 | Petroleum and natural gas industries — Steel pipes for use as casing or tubing for wells |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.