BS EN ISO 21809-3:2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Petroleum and natural gas industries. External coatings for buried or submerged pipelines used in pipeline transportation systems Field joint coatings
Hardcopy
06-06-2020
English
31-03-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 General requirements
6 Information to be supplied by the purchaser
7 Application procedures and qualification
8 Classification of field joint coatings
9 General requirements for surface preparation,
coating application, testing and repair
10 Hot-applied bituminous tape coatings
11 Petrolatum and wax-based tape coatings
12 Cold-applied polymeric tape coatings
13 Non-crystalline low-viscosity polyolefin based coatings
14 Coatings based on heat-shrinkable materials
15 Hot-applied microcrystalline wax coatings
16 Elastomeric coatings
17 Fusion-bonded epoxy (FBE) powder coatings
18 Liquid-applied coatings
19 Hot-applied polyolefin-based coatings
20 Thermal spray aluminium (TSA) coatings
Annex A (normative) - Test programmes for procedure
qualification trials (PQT), preproduction
trials (PPT) or production testing
Annex B (normative) - Inspection of thickness
Annex C (normative) - Holiday detection test
Annex D (normative) - Impact test
Annex E (normative) - Indentation test
Annex F (normative) - Specific electrical insulation resistance
Annex G (normative) - Cathodic disbondment test
Annex H (normative) - Peel strength test
Annex I (normative) - Hot water immersion test
Annex J (normative) - Lap shear strength
Annex K (normative) - Drip resistance
Annex L (normative) - Peel strength between layers
Annex M (normative) - Thermal ageing resistance
Annex N (normative) - Thermal stability test (Hot air ageing)
Annex O (normative) - Bursting strength of reinforced backing
Annex P (normative) - Thermal analysis of epoxy power and
cured coating film (FBE)
Annex Q (normative) - Adhesion test - Resistance to removal
Bibliography
Gives requirements for field joint coating of seamless or welded steel pipes for buried and submerged sections of pipeline transportation systems used in the petroleum petrochemical and natural gas industries as defined in ISO 13623.
| Committee |
PSE/17/2
|
| DevelopmentNote |
Supersedes BS EN 10329 & 14/30300605 DC. (03/2016)
|
| DocumentType |
Standard
|
| Pages |
138
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| EN ISO 21809-3:2016 | Identical |
| ISO 21809-3:2016 | Identical |
| ISO 2811-1:2016 | Paints and varnishes — Determination of density — Part 1: Pycnometer method |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| ISO 21809-2:2014 | Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 2: Single layer fusion-bonded epoxy coatings |
| ISO 8502-3:2017 | Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 3: Assessment of dust on steel surfaces prepared for painting (pressure-sensitive tape method) |
| ISO 7619-1:2010 | Rubber, vulcanized or thermoplastic Determination of indentation hardness Part 1: Durometer method (Shore hardness) |
| NACE 3 : 2007 | COMMERCIAL BLAST CLEANING |
| ISO 8501-1:2007 | Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings |
| ISO/TS 29001:2010 | Petroleum, petrochemical and natural gas industries Sector-specific quality management systems Requirements for product and service supply organizations |
| ISO 3303-1:2012 | Rubber- or plastics-coated fabrics Determination of bursting strength Part 1: Steel-ball method |
| ISO 8503-2:2012 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel — Comparator procedure |
| ASTM D 1141 : 1998 : EDT 1 | Standard Practice for the Preparation of Substitute Ocean Water |
| ISO 2808:2007 | Paints and varnishes Determination of film thickness |
| SSPC-SP 11 : 2012 | POWER-TOOL CLEANING TO BARE METAL |
| SSPC-CS 23.00 : 2016 | SPECIFICATION FOR THE APPLICATION OF THERMAL SPRAY COATINGS (METALLIZING) OF ALUMINUM, ZINC, AND THEIR ALLOYS AND COMPOSITES FOR THE CORROSION PROTECTION OF STEEL |
| ASTM D 4541 : 2017 : REDLINE | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| ISO 8503-3:2012 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 3: Method for the calibration of ISO surface profile comparators and for the determination of surface profile — Focusing microscope procedure |
| ASTM D 2084 : 2017 : REDLINE | TEST METHOD FOR RUBBER PROPERTY - VULCANIZATION USING OSCILLATING DISK CURE METER |
| ASTM D 4285 : 1983 : R2018 | Standard Test Method for Indicating Oil or Water in Compressed Air |
| ISO 34-1:2015 | Rubber, vulcanized or thermoplastic Determination of tear strength Part 1: Trouser, angle and crescent test pieces |
| ISO 8501-3:2006 | Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 3: Preparation grades of welds, edges and other areas with surface imperfections |
| ISO 4591:1992 | Plastics — Film and sheeting — Determination of average thickness of a sample, and average thickness and yield of a roll, by gravimetric techniques (gravimetric thickness) |
| ISO 4625-1:2004 | Binders for paints and varnishes Determination of softening point Part 1: Ring-and-ball method |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 11357-3:2011 | Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallization |
| ISO 11357-2:2013 | Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step height |
| ISO 1523:2002 | Determination of flash point — Closed cup equilibrium method |
| ISO 1431-1:2012 | Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing |
| ISO 4624:2016 | Paints and varnishes — Pull-off test for adhesion |
| ISO 3801:1977 | Textiles — Woven fabrics — Determination of mass per unit length and mass per unit area |
| AWS C2.25/C2.25M : 2012 | SPECIFICATION FOR THERMAL SPRAY FEEDSTOCK - WIRE AND RODS |
| ISO 10474:2013 | Steel and steel products — Inspection documents |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| SSPC-SP 6 : 2015 | COMMERCIAL BLAST CLEANING |
| ISO 80000-1:2009 | Quantities and units — Part 1: General |
| ISO 2178:2016 | Non-magnetic coatings on magnetic substrates Measurement of coating thickness Magnetic method |
| ISO 62:2008 | Plastics Determination of water absorption |
| ISO 11357-6:2008 | Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| ISO 5893:2002 | Rubber and plastics test equipment Tensile, flexural and compression types (constant rate of traverse) Specification |
| ISO 3251:2008 | Paints, varnishes and plastics Determination of non-volatile-matter content |
| ASTM D 257 : 2014 : REDLINE | Standard Test Methods for DC Resistance or Conductance of Insulating Materials |
| ISO 8502-6:2006 | Preparation of steel substrates before application of paints and related products Tests for the assessment of surface cleanliness Part 6: Extraction of soluble contaminants for analysis The Bresle method |
| ISO 8503-1:2012 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 8502-9:1998 | Preparation of steel substrates before application of paints and related products Tests for the assessment of surface cleanliness Part 9: Field method for the conductometric determination of water-soluble salts |
| SSPC-SP 5 : 2015 | WHITE METAL BLAST CLEANING |
| ASTM D 695 : 2015 : REDLINE | Standard Test Method for Compressive Properties of Rigid Plastics |
| ISO 8504-2:2000 | Preparation of steel substrates before application of paints and related products Surface preparation methods Part 2: Abrasive blast-cleaning |
| ISO 8503-4:2012 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface profile — Stylus instrument procedure |
| ISO 3417:2008 | Rubber Measurement of vulcanization characteristics with the oscillating disc curemeter |
| ASTM D 1000 : 2017 : REDLINE | Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications |
| ISO 11357-1:2016 | Plastics — Differential scanning calorimetry (DSC) — Part 1: General principles |
| ISO 527-3:1995 | Plastics Determination of tensile properties Part 3: Test conditions for films and sheets |
| ISO 8504-3:1993 | Preparation of steel substrates before application of paints and related products Surface preparation methods Part 3: Hand- and power-tool cleaning |
| ISO 8503-5:2017 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 5: Replica tape method for the determination of the surface profile |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
| ISO 13623:2017 | Petroleum and natural gas industries — Pipeline transportation systems |
| ISO 4593:1993 | Plastics Film and sheeting Determination of thickness by mechanical scanning |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| ISO 2781:2008 | Rubber, vulcanized or thermoplastic Determination of density |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.