BS EN ISO 2808:2007
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Paints and varnishes. Determination of film thickness
Hardcopy , PDF
English
30-03-2007
01-10-2019
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Determination of wet-film thickness
4.1 General
4.2 Mechanical methods
4.2.1 Principle
4.2.2 Field of application
4.2.3 General
4.2.4 Method 1A - Comb gauge
4.2.5 Method 1B - Wheel gauge
4.2.6 Method 1C - Dial gauge
4.3 Gravimetric method
4.3.1 Principle
4.3.2 Field of application
4.3.3 General
4.3.4 Method 2 - By difference in mass
4.4 Photothermal method
4.4.1 Principle
4.4.2 Field of application
4.4.3 General
4.4.4 Method 3 - Determination using thermal properties
5 Determination of dry-film thickness
5.1 General
5.2 Mechanical methods
5.2.1 Principle
5.2.2 Field of application
5.2.3 General
5.2.4 Method 4A - By difference in thickness
5.2.5 Method 4B - Depth gauging
5.2.6 Method 4C - Surface profile scanning
5.3 Gravimetric method
5.3.1 Principle
5.3.2 Field of application
5.3.3 General
5.3.4 Method 5 - By difference in mass
5.4 Optical methods
5.4.1 Principle
5.4.2 Field of application
5.4.3 General
5.4.4 Method 6A - Cross-sectioning
5.4.5 Method 6B - Wedge cut
5.5 Magnetic methods
5.5.1 General
5.5.2 Principle
5.5.3 Field of application
5.5.4 General
5.5.5 Method 7A - Magnetic pull-off gauge
5.5.6 Method 7B - Magnetic-flux gauge
5.5.7 Method 7C - Magnetic-induction gauge
5.5.8 Method 7D - Eddy-current gauge
5.6 Radiological method
5.6.1 Principle
5.6.2 Field of application
5.6.3 General
5.6.4 Method 8 - Beta backscatter method
5.7 Photothermal method
5.7.1 Principle
5.7.2 Field of application
5.7.3 General
5.7.4 Method 9 - Determination using thermal properties
5.8 Acoustic method
5.8.1 Principle
5.8.2 Field of application
5.8.3 General
5.8.4 Method 10 - Ultrasonic thickness gauge
6 Determination of thickness of uncured powder layers
6.1 General
6.2 Gravimetric method
6.2.1 Principle
6.2.2 Field of application
6.2.3 General
6.2.4 Method 11 - By difference in mass
6.3 Magnetic methods
6.3.1 Principle
6.3.2 Field of application
6.3.3 General
6.3.4 Method 12A - Magnetic-induction gauge
6.3.5 Method 12B - Eddy-current gauge
6.4 Photothermal method
6.4.1 Principle
6.4.2 Field of application
6.4.3 General
6.4.4 Method 13 - Determination using thermal properties
7 Measurement of film thickness on rough surfaces
7.1 General
7.2 Apparatus and materials
7.3 Procedure
7.3.1 Verification
7.3.2 Measurement
7.3.3 Number of readings
8 Test report
Annex A (informative) Overview of methods
Bibliography
Specifies a number of methods that are applicable to the measurement of the thickness of coatings applied to a substrate.
| Committee |
STI/10
|
| DevelopmentNote |
Renumbers and supersedes BS 3900-C5(1997). 2001 Version incorporates amendment 10893 to BS 3900-C5(1997). Supersedes BS 3900-C5(1992) and 96/121035 DC. (10/2005) Also numbered as BS 3900-C5(2007). (02/2007)
|
| DocumentType |
Standard
|
| Pages |
50
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NEN EN ISO 2808 : 2007 | Identical |
| NF EN ISO 2808 : 2007 | Identical |
| NS EN ISO 2808 : 2ED 2007 | Identical |
| EN ISO 2808:2007 | Identical |
| NBN EN ISO 2808 : 2007 | Identical |
| ISO 2808:2007 | Identical |
| I.S. EN ISO 2808:2007 | Identical |
| ONORM EN ISO 2808 : 2007 | Identical |
| UNE-EN ISO 2808:2007 | Identical |
| DEFSTAN 03-032(PT1)/5(2017) : 2017 | PRETREATMENT AND PAINTING OF VEHICLES, ENGINEER EQUIPMENT AND COMPONENTS - PART 1: GENERAL REQUIREMENTS |
| 14/30277336 DC : 0 | BS 8605-1 - EXTERNAL TIMBER CLADDING - PART 1: METHOD OF SPECIFYING |
| DEFSTAN 03-32(PT1)/4(2005) : 2005 | PRE-TREATMENT AND PAINTING OF VEHICLES, ENGINEERING EQUIPMENT AND COMPONENTS - PART 1: GENERAL REQUIREMENTS |
| DEFSTAN 03-32(PT1)/3(2002) : 2002 | PRE-TREATMENT AND PAINTING OF VEHICLES, ENGINEER EQUIPMENT AND COMPONENTS - PART 1: GENERAL REQUIREMENTS |
| DEFSTAN 80-168/4(2012) : 2012 | COMPOUND, PROTECTIVE, FOR VEHICLE UNDERBODIES, WATER-BASED |
| DEFSTAN 80-168/5(2017) : 2017 | COMPOUND, PROTECTIVE, FOR VEHICLE UNDERBODIES, WATER-BASED |
| BS 8605-1:2014 | External timber cladding Method of specifying |
| BS 1722-16:2009 | Fences Specification for powder coatings used as a plastics finish to components and mesh |
| BS 6920-2.1:2014 | Suitability of non-metallic materials and products for use in contact with water intended for human consumption with regard to their effect on the quality of the water Methods of test - Samples for testing |
| 13/30287567 DC : 0 | BS 6920-2.1 - SUITABILITY OF NON-METALLIC PRODUCTS FOR USE IN CONTACT WITH WATER INTENDED FOR HUMAN CONSUMPTION WITH REGARD TO THEIR EFFECT ON THE QUALITY OF THE WATER - PART 2: METHODS OF TEST - SECTION 2.1: SAMPLES FOR TESTING |
| 14/30277805 DC : 0 | BS 6150:2006+A1:2014 - PAINTING OF BUILDINGS - CODE OF PRACTICE |
| 07/30139517 DC : 0 | BS 1722-16 - FENCES - PART 16: SPECIFICATION FOR POWDER COATINGS USED AS A PLASTICS FINISH TO COMPONENTS AND MESH |
| BS 6150(2006) : 2006 | PAINTING OF BUILDINGS - CODE OF PRACTICE |
| ISO 2811-1:2016 | Paints and varnishes — Determination of density — Part 1: Pycnometer method |
| ISO 19840:2012 | Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Measurement of, and acceptance criteria for, the thickness of dry films on rough surfaces |
| ISO 3233:1998 | Paints and varnishes — Determination of percentage volume of non-volatile matter by measuring the density of a dried coating |
| ISO 2811-3:2011 | Paints and varnishes — Determination of density — Part 3: Oscillation method |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 8130-2:1992 | Coating powders — Part 2: Determination of density by gas comparison pyknometer (referee method) |
| DIN 50986:2015-03 | PAINTS AND VARNISHES - DETERMINATION OF DRY-FILM THICKNESS USING THE WEDGE-CUT METHOD (SCRIBE AND DRILL METHOD) |
| ISO 3543:2000 | Metallic and non-metallic coatings — Measurement of thickness — Beta backscatter method |
| ISO 1463:2003 | Metallic and oxide coatings — Measurement of coating thickness — Microscopical method |
| ASTM D 4414 : 1995 | Standard Practice for Measurement of Wet Film Thickness by Notch Gages |
| ISO 4518:1980 | Metallic coatings — Measurement of coating thickness — Profilometric method |
| ISO 2811-2:2011 | Paints and varnishes — Determination of density — Part 2: Immersed body (plummet) method |
| ISO 3611:2010 | Geometrical product specifications (GPS) — Dimensional measuring equipment: Micrometers for external measurements — Design and metrological characteristics |
| ISO 2178:2016 | Non-magnetic coatings on magnetic substrates — Measurement of coating thickness — Magnetic method |
| ISO 4618:2014 | Paints and varnishes — Terms and definitions |
| ISO 2811-4:2011 | Paints and varnishes — Determination of density — Part 4: Pressure cup method |
| ISO 8503-1:2012 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces |
| EN 15042-2:2006 | Thickness measurement of coatings and characterization of surfaces with surface waves - Part 2: Guide to the thickness measurement of coatings by photothermic method |
| DIN 50933:2015-08 | MEASUREMENT OF COATING THICKNESSES - MEASUREMENT OF THE THICKNESS OF COATINGS BY DIFFERENCE MEASUREMENT USING A STYLUS INSTRUMENT |
| ASTM D 1212 : 1991 | Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings |
| ISO 463:2006 | Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges |
| ISO 8130-3:1992 | Coating powders — Part 3: Determination of density by liquid displacement pyknometer |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.