BS EN ISO 4126-2:2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Safety devices for protection against excessive pressure Bursting disc safety devices
Hardcopy , PDF
17-06-2019
English
31-07-2009
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Materials
4.1 Selection of materials
4.2 Material specifications
4.3 Protection from corrosion
5 Types of bursting discs
5.1 Conventional domed bursting discs (forward acting)
5.2 Reverse domed bursting discs (reverse acting)
5.3 Flat bursting discs
5.4 Other types and designs
6 Bursting disc holders
6.1 Design
6.2 Types
6.3 Connections
7 Back pressure supports
7.1 General
7.2 Opening back pressure supports
7.3 Non-opening back pressure supports
8 Temperature shields
9 Stiffening rings
10 Gaskets/seals
11 Assembly of bursting disc safety devices
11.1 General
11.2 Bursting disc safety devices with replaceable
bursting disc assemblies
11.3 Bursting disc safety devices with non-replaceable
bursting disc assemblies
12 Specified bursting pressure requirements
13 Inspection by the manufacturer
14 Test procedures
14.1 General
14.2 Pressure testing
14.3 Burst testing
14.4 Leak testing
14.5 Non-destructive examination
15 Certification
16 Product designation
17 Marking
17.1 General
17.2 Bursting discs/bursting disc assemblies
17.3 Bursting disc holders
17.4 Bursting disc safety devices with non-replaceable
bursting disc assemblies
17.5 Ancillary components
17.6 Omission of markings
18 Preparation for storage and transportation
18.1 General
18.2 Marking of packages
18.3 Provision of assembly and installation instructions
18.4 Provision of documents, loose identification plates
etc.
Annex A (normative) Materials
Annex B (informative) Materials
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements
of EU Directive 97/23/EC (PED)
Bibliography
Describes the requirements for bursting disc safety devices. It includes the requirements for the design, manufacture, inspection, testing, certification, marking, and packaging.
Committee |
PSE/18/6
|
DevelopmentNote |
Supersedes 98/714280 DC. (02/2003) Supersedes BS 2915(1990). (09/2009)
|
DocumentType |
Standard
|
Pages |
40
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
I.S. EN ISO 4126-2:2003 | Identical |
NF EN ISO 4126-2 : 2003 | Identical |
NEN EN ISO 4126-2 : 2003 C11 2004 | Identical |
ISO 4126-2:2003 | Identical |
NBN EN ISO 4126-2 : 2003 COR 2006 | Identical |
SN EN ISO 4126-2 : 2003 CORR 2005 | Identical |
UNI EN ISO 4126-2 : 2003 | Identical |
ONORM EN ISO 4126-2 : 2006 | Identical |
NS EN ISO 4126-2 : 2003 AC 2006 | Identical |
UNE-EN ISO 4126-2:2003 | Identical |
DEFSTAN 02-357(PT1)/2(2009) : 2009 | REQUIREMENTS FOR GASEOUS FIREFIGHTING SYSTEMS FOR MAIN AND AUXILIARY MACHINERY SPACES ON SURFACE SHIPS - PART 1: GENERAL REQUIREMENTS FOR CARBON DIOXIDE SYSTEMS |
DEFSTAN 02-357(PT4)/1(2010) : 2010 | REQUIREMENTS FOR GASEOUS FIREFIGHTING SYSTEMS FOR MAIN AND AUXILIARY MACHINERY SPACES ON SURFACE SHIPS - PART 4: GENERAL REQUIREMENTS FOR INERT GAS SYSTEMS INCLUDING ELECTRIC/ELECTRONIC SPACES |
BS 1123:2006 | Fusible plugs for steam boilers and compressed air applications. Specification |
BS 5306-4(2001) : 2001 | FIRE EXTINGUISHING INSTALLATIONS AND EQUIPMENT ON PREMISES - PART 4: SPECIFICATION FOR CARBON DIOXIDE SYSTEMS |
BS PD5500(2006) : 2006 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
BS 5306-4:2001+A1:2012 | Fire extinguishing installations and equipment on premises Specification for carbon dioxide systems |
EEMUA 193 : 2013 | MANAGING COMPETENCE ASSURANCE FOR PERSONNEL UNDERTAKING IN-SERVICE INSPECTION OF PRESSURE EQUIPMENT |
16/30353337 DC : 0 | PD 5500:2015+A3 - SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
BS 853-1:1990+A3:2011 | Specification for vessels for use in heating systems Calorifiers and storage vessels for central heating and hot water supply |
EN 485-1:2016 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: Technical conditions for inspection and delivery |
ASTM B 364 : 1996 | Standard Specification for Tantalum and Tantalum Alloy Ingots |
BS 3073:1977 | Specification for nickel and nickel alloys: strip |
EN 10028-1:2017 | Flat products made of steels for pressure purposes - Part 1: General requirements |
ASTM B 348 : 2013 : REDLINE | Standard Specification for Titanium and Titanium Alloy Bars and Billets |
ASTM B 265 : 2015 : REDLINE | Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate |
EN 10273:2016 | Hot rolled weldable steel bars for pressure purposes with specified elevated temperature properties |
ASTM B 335 : 2003 | Standard Specification for Nickel-Molybdenum Alloy Rod |
EN 485-3:2003 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form for hot-rolled products |
ASTM B 575 : 2017 : REDLINE | Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, Low-Carbon Nickel-Chromium-Molybdenum-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Tungsten, and Low-Carbon Nickel-Molybdenum-Chromium Alloy Plate, Sheet, and Strip |
DIN 17862:2012-03 | TITANIUM AND TITANIUM ALLOY BARS - TECHNICAL SPECIFICATION |
EN 485-2:2016 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties |
EN 485-4:1993 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled products |
ASTM B 473 : 2007 | Standard Specification for UNS N08020, UNS N08024, and UNS N08026 Nickel Alloy Bar and Wire |
DIN 17744:2002-09 | WROUGHT NICKEL ALLOYS WITH MOLYBDENUM AND CHROMIUM - CHEMICAL COMPOSITION |
EN 10088-3:2014 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
EN 10087:1998 | Free-cutting steels - Technical delivery conditions for semi-finished products, hot-rolled bars and rods |
ASTM A 516/A516M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service |
ASTM B 584 : 2014 : REDLINE | Standard Specification for Copper Alloy Sand Castings for General Applications |
EN 10025:1990/A1:1993 | HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS |
EN 10216-2:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties |
ASTM B 161 : 2005 : EDT 1 | Standard Specification for Nickel Seamless Pipe and Tube |
EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
EN 10028-2:2017 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
EN 10028-7:2016 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
EN 10095:1999 | Heat resisting steels and nickel alloys |
EN ISO 6708:1995 | Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
ASTM A 351/A351M : 2016-05 | SPECIFICATION FOR CASTINGS, AUSTENITIC, FOR PRESSURE-CONTAINING PARTS |
EN 10272:2016 | Stainless steel bars for pressure purposes |
DIN 17864:2012-03 | TITANIUM AND TITANIUM WROUGHT ALLOYS FORGINGS (HAMMER AND DROP FORGINGS) - TECHNICAL SPECIFICATION |
EN 10222-3:2017 | Steel forgings for pressure purposes - Part 3: Nickel steels with specified low temperature properties |
EN 10222-5:2017 | Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels |
DIN 17742:2002-09 | WROUGHT NICKEL ALLOYS WITH CHROMIUM - CHEMICAL COMPOSITION |
ASTM B 160 : 2005 : EDT 1 | Standard Specification for Nickel Rod and Bar |
EN 10222-2:2017 | Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperatures properties |
EN 573-4:2004 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 4: Forms of products |
EN 1333:2006 | Flanges and their joints - Pipework components - Definition and selection of PN |
ASTM B 209 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
ASTM B 708 : 2012 : REDLINE | Standard Specification for Tantalum and Tantalum Alloy Plate, Sheet, and Strip |
ASTM A 105/A105M : 2014-11 | SPECIFICATION FOR CARBON STEEL FORGINGS FOR PIPING APPLICATIONS |
DIN 17743:2002-09 | WROUGHT NICKEL ALLOYS WITH COPPER - CHEMICAL COMPOSITION |
BS 3076:1989 | Specification for nickel and nickel alloys: bar |
ASTM A 312/A312M : 2017-03 | SPECIFICATION FOR SEAMLESS, WELDED, AND HEAVILY COLD WORKED AUSTENITIC STAINLESS STEEL PIPES |
DIN 17860:2010-01 | Titanium and titanium alloy strip, sheet and plate - Technical conditions of delivery |
ASTM B 381 : 2013 : REDLINE | SPECIFICATION FOR TITANIUM AND TITANIUM ALLOY FORGINGS |
EN 10028-4:2017 | Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties |
EN 573-3:2013 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products |
ASTM A 494/A494M : 2017-03 | SPECIFICATION FOR CASTINGS, NICKEL AND NICKEL ALLOY |
DIN 17740:2002-09 | WROUGHT NICKEL - CHEMICAL COMPOSITION |
EN 10222-1:2017 | Steel forgings for pressure purposes - Part 1: General requirements for open die forgings |
EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
PREN 12516-1 : DRAFT 2011 | INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 1: TABULATION METHOD FOR STEEL VALVE SHELLS |
ASTM B 333 : 2003 | Standard Specification for Nickel-Molybdenum Alloy Plate, Sheet, and Strip |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.