BS ISO 12151-3:2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Connections for hydraulic fluid power and general use. Hose fittings Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends
Hardcopy , PDF
29-11-2021
English
31-07-2010
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Performance requirements
5 Designation of hose fittings
6 Design
7 Manufacture
8 Procurement information
9 Marking
10 Identification statement (reference to this part of
ISO 12151)
Bibliography
Defines the general and dimensional requirements for the design and performance of flange hose fittings, made of carbon steel, for nominal hose inside diameters of 12,5 mm to 51 mm inclusive, in accordance with ISO 4397, for use with ports and clamps in accordance with ISO 6162-1 and ISO 6162-2.
| Committee |
MCE/18/-/4
|
| DevelopmentNote |
Supersedes 94/714848 DC. (07/2005) Supersedes 07/30163202 DC. (07/2010)
|
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This part of ISO12151 specifies the general and dimensional requirements for the design and performance of flange hose fittings, made of carbon steel, for nominal hose inside diameters of 12,5mm to 51mm inclusive, in accordance with ISO4397, for use with ports and clamps in accordance with ISO6162-1 and ISO6162-2. NOTE1 Materials other than carbon steel can be supplied as agreed between the manufacturer and user. NOTE2 For hose fittings used in hydraulic and pneumatic braking systems on road vehicles (as defined in the scope of ISO/TC22/SC2, Road vehicles), see ISO4038, ISO4039-1 and ISO4039-2. These hose fittings (see Figure1 for a typical example) are for use in hydraulic fluid power systems with hose that meets the requirements of the respective hose standards and in general applications with suitable hoses. Figure1 Typical example of hose fitting connection with ISO6162-1 or ISO6162-2 flange end Key 1 hose fitting 2 port, flanged head and clamp per ISO6162-1 or ISO6162-2 3 O-ring seal
| Standards | Relationship |
| ISO 12151-3:2010 | Identical |
| ISO 4039-1:1998 | Road vehicles — Pneumatic braking systems — Part 1: Pipes, male fittings and tapped holes with facial sealing surface |
| ISO 3862:2017 | Rubber hoses and hose assemblies Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids Specification |
| ISO 3949:2009 | Plastics hoses and hose assemblies Textile-reinforced types for hydraulic applications Specification |
| ISO 5598:2008 | Fluid power systems and components Vocabulary |
| ISO 6605:2017 | Hydraulic fluid power — Test methods for hoses and hose assemblies |
| ISO 4397:2011 | Fluid power connectors and associated components — Nominal outside diameters of tubes and nominal hose sizes |
| ISO 4039-2:1998 | Road vehicles — Pneumatic braking systems — Part 2: Pipes, male fittings and holes with conical sealing surface |
| ISO 6162-2:2012 | Hydraulic fluid power Flange connections with split or one-piece flange clamps and metric or inch screws Part 2: Flange connectors, ports and mounting surfaces for use at a pressure of 42 MPa (420 bar), DN 13 to DN 76 |
| ISO 4038:1996 | Road vehicles — Hydraulic braking systems — Simple flare pipes, tapped holes, male fittings and hose end fittings |
| ISO 4079:2017 | Rubber hoses and hose assemblies Textile-reinforced hydraulic types for oil-based or water-based fluids Specification |
| ISO 6162-1:2012 | Hydraulic fluid power — Flange connections with split or one-piece flange clamps and metric or inch screws — Part 1: Flange connectors, ports and mounting surfaces for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127 |
| ISO 19879:2010 | Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections |
| ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
| ISO 1436:2017 | Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types for oil-based or water-based fluids Specification |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.