EN 50081-1:1992
|
Electromagnetic compatibility - Generic emission standard - Part 1: Residential, commercial and light industry
|
EN 1127-1:2011
|
Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology
|
ISO 2719:2016
|
Determination of flash point — Pensky-Martens closed cup method
|
ISO 5596:1999
|
Hydraulic fluid power Gas-loaded accumulators with separator Ranges of pressures and volumes and characteristic quantities
|
ISO 4400:1994
|
Fluid power systems and components — Three-pin electrical plug connectors with earth contact — Characteristics and requirements
|
EN 418 : 1992
|
SAFETY OF MACHINERY - EMERGENCY STOP EQUIPMENT, FUNCTIONAL ASPECTS - PRINCIPLES FOR DESIGN
|
EN 982:1996+A1:2008
|
Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics
|
EN 1037:1995+A1:2008
|
Safety of machinery - Prevention of unexpected start-up
|
ISO 7368:2016
|
Hydraulic fluid power — Two-port slip-in cartridge valves — Cavities
|
ISO 10372:1992
|
Hydraulic fluid power — Four- and five-port servovalves — Mounting surfaces
|
ISO 8434-1:2007
|
Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors
|
ISO 4401:2005
|
Hydraulic fluid power — Four-port directional control valves — Mounting surfaces
|
ISO/TR 11688-1:1995
|
Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
|
ISO 5598:2008
|
Fluid power systems and components Vocabulary
|
ISO 6263:2013
|
Hydraulic fluid power — Compensated flow-control valves — Mounting surfaces
|
ISO 12151-2:2003
|
Connections for hydraulic fluid power and general use — Hose fittings — Part 2: Hose fittings with ISO 8434-1 and ISO 8434-4 24 degree cone connector ends with O-rings
|
IEC 60204-1:2016
|
Safety of machinery - Electrical equipment of machines - Part 1: General requirements
|
ISO 1219-2:2012
|
Fluid power systems and components — Graphical symbols and circuit diagrams — Part 2: Circuit diagrams
|
ISO 6162:1994
|
Hydraulic fluid power Four-screw split-flange connections for use at pressures of 2,5 MPa to 40 MPa (25 bar to 400 bar) Type I metric series and type II inch series
|
EN 414 : 2000
|
SAFETY OF MACHINERY - RULES FOR THE DRAFTING AND PRESENTATION OF SAFETY STANDARDS
|
ISO 2230:2002
|
Rubber products — Guidelines for storage
|
ISO 2941:2009
|
Hydraulic fluid power Filter elements Verification of collapse/burst pressure rating
|
EN 1050 : 1996
|
SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT
|
ISO 4412-1:1991
|
Hydraulic fluid power — Test code for determination of airborne noise levels — Part 1: Pumps
|
ISO 4572:1981
|
Hydraulic fluid power — Filters — Multi-pass method for evaluating filtration performance
|
ISO 8331:2016
|
Rubber and plastics hoses and hose assemblies Guidelines for selection, storage, use and maintenance
|
ISO 10767-1:2015
|
Hydraulic fluid power — Determination of pressure ripple levels generated in systems and components — Part 1: Method for determining source flow ripple and source impedance of pumps
|
ISO 10767-3:1999
|
Hydraulic fluid power — Determination of pressure ripple levels generated in systems and components — Part 3: Method for motors
|
EN 574:1996+A1:2008
|
Safety of machinery - Two-hand control devices - Functional aspects - Principles for design
|
EN 563:1994/A1:1999/AC:2000
|
SAFETY OF MACHINERY - TEMPERATURES OF TOUCHABLE SURFACES - ERGONOMICS DATA TO ESTABLISH TEMPERATURE LIMIT VALUES FOR HOT SURFACES
|
ISO 7789:2007
|
Hydraulic fluid power Two-, three- and four-port screw-in cartridge valves Cavities
|
ISO 8434-2:2007
|
Metallic tube connections for fluid power and general use — Part 2: 37 degree flared connectors
|
ISO 6264:1998
|
Hydraulic fluid power — Pressure-relief valves — Mounting surfaces
|
ISO 6072:2011
|
Rubber Compatibility between hydraulic fluids and standard elastomeric materials
|
ISO 5781:2016
|
Hydraulic fluid power Pressure-reducing valves, sequence valves, unloading valves, throttle valves and check valves Mounting surfaces
|
ISO 10767-2:1999
|
Hydraulic fluid power Determination of pressure ripple levels generated in systems and components Part 2: Simplified method for pumps
|
ISO 12151-3:2010
|
Connections for hydraulic fluid power and general use Hose fittings Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends
|
ISO 8434-3:2005
|
Metallic tube connections for fluid power and general use — Part 3: O-ring face seal connectors
|
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV
|
Degrees of protection provided by enclosures (IP Code)
|
ISO 10100:2001
|
Hydraulic fluid power Cylinders Acceptance tests
|
ISO 6149-1:2006
|
Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 1: Ports with truncated housing for O-ring seal
|
ISO 2942:2004
|
Hydraulic fluid power Filter elements Verification of fabrication integrity and determination of the first bubble point
|
ISO 6164:1994
|
Hydraulic fluid power Four-screw, one-piece square-flange connections for use at pressures of 25 MPa and 40 MPa (250 bar and 400 bar)
|
ISO 12100-2:2003
|
Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
|
ISO 8434-4:1995
|
Metallic tube connections for fluid power and general use Part 4: 24 degree cone connectors with O-ring weld-on nipples
|
ISO 1219-1:2012
|
Fluid power systems and components — Graphical symbols and circuit diagrams — Part 1: Graphical symbols for conventional use and data-processing applications
|
ISO 12151-1:2010
|
Connections for hydraulic fluid power and general use — Hose fittings — Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends
|
ISO 10763:1994
|
Hydraulic fluid power Plain-end, seamless and welded precision steel tubes Dimensions and nominal working pressures
|
EN 954-1 : 1996
|
SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN
|
ISO 12100-1:2003
|
Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
|
ISO 13850:2015
|
Safety of machinery Emergency stop function Principles for design
|
ISO 2943:1998
|
Hydraulic fluid power Filter elements Verification of material compatibility with fluids
|
ISO 4021:1992
|
Hydraulic fluid power — Particulate contamination analysis — Extraction of fluid samples from lines of an operating system
|
ISO 2944:2000
|
Fluid power systems and components — Nominal pressures
|
ISO 6952:1994
|
Fluid power systems and components Two-pin electrical plug connectors with earth contact Characteristics and requirements
|
ISO 4412-3:1991
|
Hydraulic fluid power — Test code for determination of airborne noise levels — Part 3: Pumps — Method using a parallelepiped microphone array
|
ISO 4412-2:1991
|
Hydraulic fluid power — Test code for determination of airborne noise levels — Part 2: Motors
|
ISO 7790:2013
|
Hydraulic fluid power — Four-port modular stack valves and four-port directional control valves, sizes 02, 03, 05, 07, 08 and 10 — Clamping dimensions
|
ISO 3724:2007
|
Hydraulic fluid power — Filter elements — Determination of resistance to flow fatigue using particulate contaminant
|
ISO 6743-4:2015
|
Lubricants, industrial oils and related products (class L) Classification Part 4: Family H (Hydraulic systems)
|
ISO 7241-1:1987
|
Hydraulic fluid power Quick-action couplings Part 1: Dimensions and requirements
|
ISO 7745:2010
|
Hydraulic fluid power — Fire-resistant (FR) fluids — Requirements and guidelines for use
|
EN 50082-1:1997
|
Electromagnetic compatibility - Generic immunity standard - Part 1: Residential, commercial and light industry
|