BS ISO 6966-2:2014
Current
The latest, up-to-date edition.
Aircraft ground equipment. Basic requirements Safety requirements
Hardcopy , PDF
English
31-08-2014
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Markings
6 Manufacturer's instructions
7 Quality assurance
8 Operator's responsibilities
Annex A (informative) - List of typical aircraft
ground support equipment
Annex B (normative) - Falling hazard symbol
Annex C (normative) - Inching speed symbol
Bibliography
Describes the minimum design requirements applicable to all aircraft ground support equipment (GSE), in order to ensure: a) safety of staff operating or maintaining the equipment or in its vicinity, and b) protection of aircraft against interference or damage.
Committee |
ACE/57
|
DevelopmentNote |
Supersedes 04/30122777 DC. (03/2006) Supersedes 13/30263819 DC. (08/2014)
|
DocumentType |
Standard
|
Pages |
38
|
PublisherName |
British Standards Institution
|
Status |
Current
|
Supersedes |
This part of ISO6966 specifies the minimum design requirements applicable to all aircraft ground support equipment (GSE), as defined in 3.1 hereafter, in order to ensure safety of staff operating or maintaining the equipment or in its vicinity, and protection of aircraft against interference or damage. An informative list of the most commonly used pieces of ground equipment is provided in AnnexA hereafter. Nevertheless, the requirements of this part of ISO6966 apply to any piece of aircraft ground support equipment, as defined, used on airports. This part of ISO6966 does not intend to provide all the design requirements applicable for aircraft ground support equipment. Other requirements apply, and can be found in separate International Standards: ISO6966-1 specifies the general, other than safety-related, requirements applicable to all aircraft ground support equipment; ISO4116 specifies the additional requirements applicable for conveying surfaces of those pieces of aircraft ground support equipment intended for handling and loading of baggage and cargo unit load devices; specific International Standards, listed in the Bibliography, define the functional and performance requirements for certain types of aircraft ground support equipment. In most countries, standing Government Health and Safety laws and regulations apply to machinery, implicitly or explicitly, including aircraft ground support equipment. Nothing in this part of ISO6966, however, shall be deemed or otherwise used to supersede any locally applicable law or regulation, unless a specific exemption has been obtained for this purpose from the appropriate Authority. This part of ISO6966 does not apply to automotive vehicles or parts thereof approved for public vehicles, when used on aircraft ground support equipment for the purpose for which they are designed.
Standards | Relationship |
ISO 6966-2:2014 | Identical |
ISO 9667:2017 | Aircraft ground support equipment — Tow bars |
ISO 9678:1991 | Aircraft — Self-propelled potable-water vehicle |
ISO 7010:2011 | Graphical symbols Safety colours and safety signs Registered safety signs |
ISO 6966-1:2005 | Aircraft ground equipment — Basic requirements — Part 1: General design requirements |
EN 1915-3:2004+A1:2009 | Aircraft ground support equipment - General requirements - Part 3: Vibration measurement methods and reduction |
ISO 14122-3:2016 | Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails |
ISO 14122-1:2016 | Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means and general requirements of access |
ISO 20683-1:2016 | Aircraft ground equipment Nose gear towbarless towing vehicle (TLTV) Design, testing and maintenance requirements Part 1: Main line aircraft |
SIA A92.7 : 2014 | AIRLINE GROUND SUPPORT VEHICLE-MOUNTED VERTICAL LIFT DEVICES |
ISO 11077:2014 | Aircraft ground equipment De-icers Functional requirements |
CFR 29(PTS1900-1910) : 0 | LABOR - OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR |
ISO 11228-2:2007 | Ergonomics — Manual handling — Part 2: Pushing and pulling |
ISO 3411:2007 | Earth-moving machinery Physical dimensions of operators and minimum operator space envelope |
ISO 10841:1996 | Aircraft — Catering vehicle for large capacity aircraft — Functional requirements |
ISO 6967:2006 | Aircraft ground equipment — Main deck loader — Functional requirements |
ISO 9666:1993 | Aircraft — Self-propelled lavatory-servicing vehicle — Functional requirements |
ISO 13732-1:2006 | Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces |
ISO 6858:1982 | Aircraft Ground support electrical supplies General requirements |
SAE AIR1558B | Interface Protective Devices - Ground Equipment to Aircraft |
IEC 60825-1:2014 | Safety of laser products - Part 1: Equipment classification and requirements |
ISO 1464:1985 | Aerospace Tripod jacks Clearance dimensions |
EN 1915-4:2004+A1:2009 | Aircraft ground support equipment - General requirements - Part 4: Noise measurement methods and reduction |
ISO 14122-4:2016 | Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders |
ISO 14121-1:2007 | Safety of machinery Risk assessment Part 1: Principles |
ISO 7731:2003 | Ergonomics Danger signals for public and work areas Auditory danger signals |
ISO 3795:1989 | Road vehicles, and tractors and machinery for agriculture and forestry — Determination of burning behaviour of interior materials |
DIN 51130:2014-02 | Testing of floor coverings - Determination of the anti-slip property - Workrooms and fields of activities with slip danger - Walking method - Ramp test |
SAE ARP1328B | Aircraft Ground Support Equipment - Wind Stability Determination |
SAE ARP 1801 : 2012 | MEASUREMENT OF EXTERIOR SOUND LEVEL OF SPECIALIZED AIRCRAFT GROUND SUPPORT EQUIPMENT |
ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
ISO 7716:1985 | Air cargo equipment — Unit load devices transport vehicle (UTV) — Functional requirements |
ISO 4116:1986 | Air cargo equipment — Ground equipment requirements for compatibility with aircraft unit load devices |
SAE ARP1247D | Aircraft Ground Support Equipment — General Requirements |
ISO 3457:2003 | Earth-moving machinery — Guards — Definitions and requirements |
EN 1915-2:2001+A1:2009 | Aircraft ground support equipment - General requirements - Part 2: Stability and strength requirements, calculations and test methods |
ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
ISO 20683-2:2016 | Aircraft ground equipment Design, testing and maintenance requirements for nose gear towbarless towing vehicle (TLTV) Part 2: Regional aircraft |
ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
ISO 9001:2015 | Quality management systems — Requirements |
ISO 27471:2012 | Aircraft ground equipment — Upper deck loader — Functional requirements |
ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
ISO 10254:1995 | Air cargo and ground equipment Vocabulary |
SAE AIR1375D | Minimum Safety Requirements for Special Purpose Airline Ground Support Equipment |
ISO 6968:2005 | Aircraft ground equipment — Lower deck loader — Functional requirements |
ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
EN 1915-1:2013 | Aircraft ground support equipment - General requirements - Part 1: Basic safety requirements |
ISO 11995:1996 | Aircraft — Stability requirements for loading and servicing equipment |
ISO 27470:2011 | Aircraft ground equipment Upper deck catering vehicle Functional requirements |
ISO 12056:1996 | Aircraft — Self-propelled passenger stairs for large capacity aircraft — Functional requirements |
IEC 62061:2005+AMD1:2012+AMD2:2015 CSV | Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems |
ISO 14122-2:2016 | Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways |
ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.