BS ISO 8062-4:2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Geometrical product specifications (GPS). Dimensional and geometrical tolerances for moulded parts General tolerances for castings using profile tolerancing in a general datum system
Hardcopy , PDF
20-06-2023
English
23-08-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Rules
6 General tolerances
7 Required machining allowances
8 Draft angles (tapers)
9 General drawing indication
Annex A (informative) - Concept of general tolerancing
Annex B (informative) - Selection of general tolerances
Annex C (informative) - Selection of required machining
allowances (RMAs)
Annex D (informative) - Example of using general tolerances
Annex E (informative) - Calculation of the nominal dimension
of the moulded condition
Annex F (informative) - Relation to the GPS matrix model
Bibliography
Gives general geometrical tolerances using surface profile tolerances related to a general datum system that remains on the final part and also specifies machining allowances and draft angles (tapers) for castings in all cast metals and their alloys produced by various casting manufacturing processes.
| Committee |
TPR/1
|
| DevelopmentNote |
Partially Supersedes BS EN ISO 8062-3. Supersedes 14/30262683 DC. (09/2017)
|
| DocumentType |
Standard
|
| Pages |
36
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This document specifies general geometrical tolerances using surface profile tolerances related to a general datum system that remains on the final part. It also specifies machining allowances and draft angles (tapers) for castings in all cast metals and their alloys produced by various casting manufacturing processes.
NOTE When there is no datum system (target or integral) on surfaces remaining in the final condition, this document cannot be applied.
| Standards | Relationship |
| ISO 8062-4:2017 | Identical |
| ISO 8015:2011 | Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules |
| ISO 14638:2015 | Geometrical product specifications (GPS) Matrix model |
| ISO 5459:2011 | Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems |
| ISO 2692:2014 | Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 14253-1:2017 | Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications |
| ISO 8062-3:2007 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings |
| ISO/TS 8062-2:2013 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 2: Rules |
| ISO 14405-2:2011 | Geometrical product specifications (GPS) Dimensional tolerancing Part 2: Dimensions other than linear sizes |
| ISO 10135:2007 | Geometrical product specifications (GPS) — Drawing indications for moulded parts in technical product documentation (TPD) |
| ISO 1302:2002 | Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation |
| ISO 8062-1:2007 | Geometrical product specifications (GPS) Dimensional and geometrical tolerances for moulded parts Part 1: Vocabulary |
| ISO 1660:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Profile tolerancing |
| ISO 10579:2010 | Geometrical product specifications (GPS) — Dimensioning and tolerancing — Non-rigid parts |
| ISO 5458:1998 | Geometrical Product Specifications (GPS) Geometrical tolerancing Positional tolerancing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.