• CSA C22.2 No. 0.17 : 2000

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    EVALUATION OF PROPERTIES OF POLYMERIC MATERIALS

    Available format(s):  Hardcopy, PDF

    Superseded date:  14-07-2021

    Language(s):  English

    Published date:  01-01-2013

    Publisher:  Canadian Standards Association

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Preface
    Foreword
    1. Scope
    2. Definitions, Reference Publications, and Abbreviations
    3. General Requirements
    4. Flame Test Procedure
    5. Mechanical Properties
    6. Electrical Properties
    7. Relative Thermal Index (RTI)
    8. Marking
    9. End-Product Testing
    Appendices
    A - ISO/IEC Equivalent Standards
    B - Needle-Flame Test
    C - Flame Tests Equivalency Table
    D - Flame Tests

    Abstract - (Show below) - (Hide below)

    Describes procedures for evaluating polymeric materials and parts made from polymeric materials intended for application in electrical equipment covered by the Canadian Electrical Code, Part II (CEC, Part II), with respect to: (a) flammability; (b) mechanical properties; (c) thermal properties; (d) resistance to weathering; and (e) electrical properties.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Product Note Reconfirmed EN
    Publisher Canadian Standards Association
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
    IEC 60695-11-20:2015 Fire hazard testing - Part 11-20: Test flames - 500 W flame test method
    IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
    ISO 75-1:2013 Plastics Determination of temperature of deflection under load Part 1: General test method
    ISO 6603-2:2000 Plastics Determination of puncture impact behaviour of rigid plastics Part 2: Instrumented impact testing
    ASTM D 495 : 2014 Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation
    ISO 2896:2001 Rigid cellular plastics Determination of water absorption
    ASTM D 618 : 2013 : REDLINE Standard Practice for Conditioning Plastics for Testing
    ASTM D 3638 : 2012 : REDLINE Standard Test Method for Comparative Tracking Index of Electrical Insulating Materials
    UL 94 : 6 TESTS FOR FLAMMABILITY OF PLASTIC MATERIALS FOR PARTS IN DEVICES AND APPLIANCES
    ISO 6603-1:2000 Plastics Determination of puncture impact behaviour of rigid plastics Part 1: Non-instrumented impact testing
    ISO 9773:1998 Plastics — Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source
    IEC 60216-4-1:2006 Electrical insulating materials - Thermal endurance properties - Part 4-1: Ageing ovens - Single-chamber ovens
    ASTM D 5207 : 2014 : REDLINE Standard Practice for Confirmation of 20–mm (50–W) and 125–mm (500–W) Test Flames for Small-Scale Burning Tests on Plastic Materials
    ISO 8256:2004 Plastics Determination of tensile-impact strength
    UL 746C : 6 POLYMERIC MATERIALS - USE IN ELECTRICAL EQUIPMENT EVALUATIONS
    IEC 60216-2:2005 Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria
    IEC 60695-2-1-0 : 1.0 FIRE HAZARD TESTING - TEST METHODS - GLOW-WIRE TEST METHODS - GENERAL
    ISO 1798:2008 Flexible cellular polymeric materials Determination of tensile strength and elongation at break
    ISO 75-2:2013 Plastics Determination of temperature of deflection under load Part 2: Plastics and ebonite
    ISO 527-2:2012 Plastics Determination of tensile properties Part 2: Test conditions for moulding and extrusion plastics
    ASTM D 1525 : 2017 Standard Test Method for Vicat Softening Temperature of Plastics
    IEC 60093:1980 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
    ISO 180:2000 Plastics Determination of Izod impact strength
    ISO 9772:2012 Cellular plastics Determination of horizontal burning characteristics of small specimens subjected to a small flame
    ASTM D 149 : 2009 TEST METHOD FOR DIELECTRIC BREAKDOWN VOLTAGE AND DIELECTRIC STRENGTH OF SOLID ELECTRICAL INSULATING MATERIALS AT COMMERCIAL POWER FREQUENCIES
    ASTM D 790 : 2017 : REDLINE Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
    IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
    ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
    ISO 4046:1978 Paper, board, pulp and related terms Vocabulary
    ASTM G 155 : 2013 : REDLINE Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials
    ISO 62:2008 Plastics Determination of water absorption
    ASTM D 648 : 2016 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
    ASTM D 5420 : 2016 : REDLINE Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
    ISO 306:2013 Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
    IEC TS 60695-11-3:2004 Fire hazard testing - Part 11-3: Test flames - 500 W flames - Apparatus and confirmational test methods
    ASTM D 257 : 2014 : REDLINE Standard Test Methods for DC Resistance or Conductance of Insulating Materials
    IEC 60695-10-2:2014 Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method
    ASTM D 3801 : 2010-08 TEST METHOD FOR MEASURING THE COMPARATIVE BURNING CHARACTERISTICS OF SOLID PLASTICS IN A VERTICAL POSITION
    IEC 60216-5:2008 Electrical insulating materials - Thermal endurance properties - Part 5: Determination of relative thermal endurance index (RTE) of an insulating material
    IEC 60216-3-1:1990 Guide for the determination of thermal endurance properties of electrical insulating materials. Part 3: Instructions for calculating thermal endurance characteristics - Section 1: Calculations using mean values of normally distributed complete data
    ASTM D 1822 : 2013 : REDLINE Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials
    ASTM D 570 : 1998 : R2018 Standard Test Method for Water Absorption of Plastics
    ISO 178:2010 Plastics Determination of flexural properties
    ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
    IEC 60216-1:2013 Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results
    ASTM E 162 : 2016 : REDLINE Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
    IEC 60216-3-2:1993 Guide for the determination of thermal endurance properties of electrical insulating materials - Part 3: Instructions for calculating thermal endurance characteristics - Section 2: Calculations for incomplete data: proof test results up to and including the median time to end-point (equal test groups)
    ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
    ISO 1629:2013 Rubber and latices Nomenclature
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    ASTM D 5423 : 2014 Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective