DEFSTAN 02-860(PT1)/1(2003) : 2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
REQUIREMENTS FOR THE DESIGN AND MANUFACTURE OF PORTABLE FIRE EXTINGUISHERS - PART 1: SHOCK SUPPORT BRACKETS
12-01-2013
12-03-2010
TITLE PAGE
SCOPE
FOREWORD
Sponsorship
Conditions of Release
Categories of Defence Standard
Related Documents
Health and Safety
Additional Information
CONTENTS
SECTION 1 - PERFORMANCE SPECIFICATION
1.1 General
SECTION 2 - NATIONAL/INTERNATIONAL REGULATIONS
SECTION 3 - MILITARY STANDARDS/REQUIREMENTS
3.1 Drawings
3.2 Materials
3.3 Environmental Conditions
3.4 Testing
3.5 Labelling and Marking
3.6 Inspection and Quality Control
3.6.1 Inspection
3.6.2 Quality Control
3.7 Packaging
SECTION 4 - DESIGN REQUIREMENTS/GUIDANCE
SECTION 5 - CORPORATE EXPERIENCE & KNOWLEDGE
ANNEX A - RELATED DOCUMENTS
ANNEX B - ABBREVIATIONS AND DEFINITIONS
ANNEX C - PROCUREMENT CHECK LIST
ALPHABETICAL INDEX
Gives the requirements for the design and manufacture of Shock Support Brackets and Fixings for all portable Fire Extinguishers as described in BS EN 3 Part 5, DEFSTAN 07-204 Parts 1 and 3, DEFSTAN 02-860 Parts 2, 3 and 4, BR 2170, BR 4007 and BR 8470 as used on board HM Surface Ships and Submarines.
| DocumentType |
Standard
|
| PublisherName |
UK Ministry of Defence Standards
|
| Status |
Superseded
|
| SupersededBy |
| BS 381C:1996 | Specification for colours for identification, coding and special purposes |
| BS 6001-4:1994 | Sampling procedures for inspection by attributes Specification for sequential sampling plans |
| BS EN 603-2:1997 | Aluminium and aluminium alloys. Wrought forging stock Mechanical properties |
| BS 308-1:1993 | Engineering drawing practice Recommendations for general principles |
| DEFSTAN 08-123/1(2000) : 2000 | REQUIREMENTS FOR THE DESIGN AND TESTING OF EQUIPMENTS TO MEET ENVIRONMENTAL CONDITIONS - CATEGORY 2 |
| BS EN 586-2:1994 | Aluminium and aluminium alloys. Forgings Mechanical properties and additional property requirements |
| BS EN 3-5:1996 | Portable fire extinguishers Specification and supplementary tests |
| DEFSTAN 00-35(PT5)/3(1999) : 1999 | ENVIRONMENTAL HANDBOOK FOR DEFENCE MATERIEL - PART 5: INDUCED MECHANICAL ENVIRONMENTS |
| BS EN 604-1:1997 | Aluminium and aluminium alloys. Cast forging stock Technical conditions for inspection and delivery |
| DEFSTAN 02-723/1(2000) : 2000 | REQUIREMENTS FOR MARKER PLATES |
| DEFSTAN 07-204(PT1)/1(2000) : 2000 | THE REQUIREMENT FOR FIRE PROTECTION AND DAMAGE CONTROL FOR SURFACE SHIPS - CATEGORY 2 - PART 1: POLICY FOR SURFACE SHIPS |
| BS 6001-1(1999) : 1999 | SAMPLING PROCEDURES FOR INSPECTION BY ATTRIBUTES - PART 1: SAMPLING SCHEMES INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION |
| BS 3451:1973 | Methods of testing fusion welds in aluminium and aluminium alloys |
| BS 5306-3:2000 | Fire extinguishing installations and equipment on premises Maintenance of portable fire extinguishers. Code of practice |
| DEFSTAN 02-722/1(2000) : 2000 | REQUIREMENTS FOR THE PREPARATION, IDENTIFICATION AND MANAGEMENTS OF DRAWINGS |
| DEFSTAN 05-10/4(1990) : 1990 | DRAWING PROCEDURE |
| DEFSTAN 02-749(PT2)/1(2000) : 2000 | REQUIREMENTS FOR ALUMINIUM-NICKEL-SILICON-BRASS - PART 2: FORGINGS, FORGING STOCK, RODS AND SECTIONS |
| BS 1134-2:1990 | Assessment of surface texture. Guidance and general information |
| BS 6001-3:1993 | Sampling procedures for inspection by attributes Specification for skip-lot procedures |
| BS EN 586-1:1998 | Aluminium and aluminium alloys. Forgings Technical conditions for inspection and delivery |
| BS 6001-0:1996 | Sampling procedures for inspection by attributes Introduction to the BS 6001 attribute sampling system |
| BS 1449-1.1:1991 | Steel plate, sheet and strip. Carbon and carbon-manganese plate, sheet and strip General specification |
| DEFSTAN 07-204(PT3)/1(2000) : 2000 | THE REQUIREMENT FOR FIRE PROTECTION AND DAMAGE CONTROL FOR SURFACE SHIPS - CATEGORY 2 - PART 3: SURFACE SHIP AND SUBMARINE EQUIPMENT |
| BS EN 573-3:2013 | Aluminium and aluminium alloys. Chemical composition and form of wrought products Chemical composition and form of products |
| BS EN 603-1:1997 | Aluminium and aluminium alloys. Wrought forging stock Technical conditions for inspection and delivery |
| BS 4781:1990 | Specification for pressure-sensitive adhesive plastics labels for permanent use |
| BS EN 515:2017 | Aluminium and aluminium alloys. Wrought products. Temper designations |
| DEFSTAN 00-35(PT3)/3(1999) : 1999 | ENVIRONMENTAL HANDBOOK FOR DEFENCE MATERIEL - PART 3: ENVIRONMENTAL TEST METHODS |
| BS EN 604-2:1997 | Aluminium and aluminium alloys. Cast forging stock Tolerances on dimensions and form |
| DEFSTAN 00-35(PT4)/3(1999) : 1999 AMD 1 2000 | ENVIRONMENTAL HANDBOOK FOR DEFENCE MATERIEL - PART 4: NATURAL ENVIRONMENTS |
| BS EN ISO 8402:1995 | Quality management and quality assurance. Vocabulary |
| BS 6975:1988 | Specification for non-metallic tensional strapping |
| BS EN 573-4:2004 | Aluminium and aluminium alloys. Chemical composition and form of wrought products Forms of products |
| DEFSTAN 81-41(PT1)/5(2003) : 2003 | PACKAGING OF DEFENCE MATERIAL - PART 1: INTRODUCTION TO DEFENCE PACKAGING REQUIREMENTS |
| BS 6001-5:2002 | Sampling procedures for inspection by attributes Procedures for assessment of declared quality levels |
| DEFSTAN 02-724/1(2000) : 2000 | PACKAGING |
| DEFSTAN 00-35(PT1)/3(1999) : 1999 | ENVIRONMENTAL HANDBOOK FOR DEFENCE MATERIEL - PART 1: CONTROL AND MANAGEMENT |