DIN EN 12733:2016-08 (Draft)
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
AGRICULTURAL AND FORESTRY MACHINERY - PEDESTRIAN CONTROLLED MOTOR MOWERS - SAFETY
Hardcopy , PDF
07-03-2021
German
01-01-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Vorwort
Einleitung
1 Anwendungsbereich
2 Normative Verweisungen
3 Begriffe
4 Liste der Gefährdungen
5 Sicherheitsanforderungen und/oder Massnahmen
5.1 Allgemeines
5.2 Einrichtungen zum Anlassen und Abstellen des Motors
5.3 Stellteile
5.4 Kennzeichnung von Stellteilen
5.5 Stellteile zur Bewegung der Maschine und des
Messers (der Messer)
5.6 Rückwärtsgang
5.7 Führungsholme
5.8 Unter Druck stehende Teile
5.9 Austreten von Flüssigkeiten
5.10 Abgasanlage
5.11 Lenkanlage
5.12 Bremsen
5.13 Elektrische Leitungen
5.14 Geräusche
5.15 Schwingungen
6 Besondere Anforderungen
6.1 Balkenmäher
6.2 Aufwuchsmäher
6.3 Schlegelmäher
6.4 Gestrüppmäher
7 Benutzerinformationen
7.1 Betriebsanleitung
7.2 Kennzeichnung
Anhang A (normativ) Liste der Gefährdungen
Anhang B (normativ) Geräuschmessung für Motormäher
- Rechnerische Methode (Grad 2)
Anhang C (normativ) Schwingungsmessung bei Motormähern
Anhang D (normativ) Prüfung mit dem Prüffuss
Anhang E (normativ) Material der Schutztücher
Anhang F (normativ) Durchdringungsprüfung an Wellpappe
für die Prüfung von Aufwuchsmähern - Zielwände
des Prüfstandes
Anhang G (normativ) Höhenbereiche
Anhang H (normativ) Prüfstand
Anhang I (normativ) Wurfkörperprüfung für Schlegelmäher
Anhang J (normativ) Wurfkörperprüfung für Gestrüppmäher
Anhang K (informativ) Beispiel für ein Material und Aufbau
zur Erfüllung der Anforderungen an eine künstliche
Oberfläche
Anhang L (informativ) Beispiele von Maschinen
Anhang ZA (informativ) Zusammenhang zwischen dieser
Europäischen Norm und den grundlegenden
Anforderungen der EG-Richtlinie 98/37/EG,
geändert durch Richtlinie 98/79/EG
Anhang ZB (informativ) Zusammenhang zwischen dieser
Europäischen Norm und den grundlegenden
Anforderungen der EG-Richtlinie 2006/42/EG
Literaturhinweise
Defines safety requirements and their verification for design and construction of pedestrian controlled motor mowers with rotary or reciprocating cutting blades used in agricultural, forestry and landscaping to cut and/or mulch grass or similar plants or scrub and woody vegetation.
| DevelopmentNote |
DRAFT 2016 issued in August 2016. (08/2016)
|
| DocumentType |
Draft
|
| Pages |
191
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Standards | Relationship |
| UNE-EN 12733:2002 | Identical |
| UNI EN 12733 : 2009 | Identical |
| NF EN 12733 : 2001 + A1 2009 | Identical |
| ONORM EN 12733 : 2011 | Identical |
| NEN EN 12733 : 2001 + A1 2009 | Identical |
| NBN EN 12733 : 2001 + A1 2009 | Identical |
| BS EN 12733 : 2001 | Identical |
| NS EN 12733 : 2001 + A1 2009 | Identical |
| I.S. EN 12733:2001 | Identical |
| EN 12733:2001+A1:2009 | Identical |
| SN EN 12733 : 2001 + A1 2009 | Identical |
| EN 294:1992/AC:1993 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS |
| ISO 3789-1:1982 | Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Location and method of operation of operator controls — Part 1: Common controls |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| ISO 354:2003 | Acoustics — Measurement of sound absorption in a reverberation room |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| EN 836:1997+A4:2011 | Garden equipment - Powered lawnmowers - Safety |
| ISO 3767-3:2016 | Tractors, machinery for agriculture and forestry, powered lawn and garden equipment Symbols for operator controls and other displays Part 3: Symbols for powered lawn and garden equipment |
| EN 1033 : 1995 | HAND-ARM VIBRATION - LABORATORY MEASUREMENT OF VIBRATION AT THE GRIP SURFACE OF HAND-GUIDED MACHINERY - GENERAL |
| ISO 5718-2:1991 | Harvesting equipment Flat blades for rotary mowers Part 2: Specifications for type B flat blades |
| ISO 11102-1:1997 | Reciprocating internal combustion engines Handle starting equipment Part 1: Safety requirements and tests |
| ISO 2758:2014 | Paper Determination of bursting strength |
| EN ISO 11820:1996 | Acoustics - Measurements on silencers in situ (ISO 11820:1996) |
| EN ISO 11688-2:2000 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998) |
| EN 292-1 : 1991 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - BASIC TERMINOLOGY, METHODOLOGY |
| EN 60804:2000 | Integrating-averaging sound level meters |
| CR 1030-1:1995 | Hand-arm vibration - Guidelines for vibration hazards reduction - Part 1: Engineering methods by design of machinery |
| EN 563:1994/A1:1999/AC:2000 | SAFETY OF MACHINERY - TEMPERATURES OF TOUCHABLE SURFACES - ERGONOMICS DATA TO ESTABLISH TEMPERATURE LIMIT VALUES FOR HOT SURFACES |
| ISO 11820:1996 | Acoustics — Measurements on silencers in situ |
| EN ISO 11201:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010) |
| EN ISO 354:2003 | Acoustics - Measurement of sound absorption in a reverberation room (ISO 354:2003) |
| ISO 3767-1:2016 | Tractors, machinery for agriculture and forestry, powered lawn and garden equipment Symbols for operator controls and other displays Part 1: Common symbols |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| EN ISO 11806:2008 | Agricultural and forestry machinery - Portable hand-held combustion engine driven brush cutters and grass trimmers - Safety (ISO 11806:1997) |
| EN 292-2 : 91 AMD 1 95 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - TECHNICAL PRINCIPLES AND SPECIFICATION |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| EN 60651:1994/A2:2001 | SOUND LEVEL METERS (IEC 60651:1979/A2:2000) |
| EN ISO 11691:2009 | Acoustics - Measurement of insertion loss of ducted silencers without flow - Laboratory survey method (ISO 11691:1995) |
| ISO 11806:1997 | Agricultural and forestry machinery Portable hand-held combustion engine driven brush cutters and grass trimmers Safety |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO 11201:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
| EN 745:1999+A1:2009 | Agricultural machinery - Rotary mowers and flail-mowers - Safety |
| ISO 11691:1995 | Acoustics Measurement of insertion loss of ducted silencers without flow Laboratory survey method |
| IEC 60651:1979+AMD1:1993+AMD2:2000 CSV | Sound level meters |
| IEC 60804:2000 | Integrating-averaging sound level meters |
| ISO 5718-1:1989 | Harvesting equipment — Flat blades for rotary mowers — Specifications — Part 1: Type A flat blades |
| ISO 11102-2:1997 | Reciprocating internal combustion engines Handle starting equipment Part 2: Method of testing the angle of disengagement |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.