DIN EN 1760-1:1997-09
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 1: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE MATS AND PRESSURE SENSITIVE FLOORS
Hardcopy , PDF
01-08-2013
English
01-01-1997
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions
4 Requirements
5 Marking
6 Information for use
7 Testing
Annex A (normative) - Timing diagrams for devices with and
without reset
Annex B (informative) - Application notes
Annex C (informative) - Design notes
Annex D (informative) - Installation, commissioning and test
Annex E (informative) - Bibliography
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 98/37/EC
Annex ZB (informative) - Relationship between this European
Standard and the Essential Requirements of EU Directive
2006/42/EC
National Annex NA (informative) - Bibliography
Defines requirements for pressure sensitive mats and floors normally actuated by the feet for use as safety devices to protect persons from dangerous machinery.
DocumentType |
Standard
|
Pages |
48
|
PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
Status |
Superseded
|
Standards | Relationship |
BS EN 1760-1 : 1998 | Identical |
NF EN 1760-1 : 1997 + A1 2009 | Identical |
UNI EN 1760-1 : 2009 | Identical |
NS EN 1760-1 : 1997 + A1 2009 | Identical |
SN EN 1760-1 : 1998 + A1 2009 | Identical |
EN 1760-1:1997+A1:2009 | Identical |
NBN EN 1760-1 : 1997 + A1 2009 | Identical |
I.S. EN 1760-1:1998 | Identical |
NEN EN 1760-1 : 1997 + A1 2009 | Identical |
UNE-EN 1760-1:1998 | Identical |
EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
IEC 61310-2:2007 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
EN 981:1996+A1:2008 | Safety of machinery - System of auditory and visual danger and information signals |
IEC 60073:2002 | Basic and safety principles for man-machine interface, marking and identification - Coding principles for indicators and actuators |
EN 61310-2:2008 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
ISO 7250:1996 | Basic human body measurements for technological design |
EN 60073:2002 | Basic and safety principles for man-machine interface, marking and identification - Coding principles for indicators and actuators |
EN ISO 14121-1:2007 | Safety of machinery - Risk assessment - Part 1: Principles (ISO 14121-1:2007) |
EN 999:1998+A1:2008 | Safety of machinery - The positioning of protective equipment in respect of approach speeds of parts of the human body |
EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
IEC 61000-4-4:2012 RLV | Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test |
DIN EN 60068-2-6 : 1996 | ENVIRONMENTAL TESTING - PART 2-6: TESTS - TEST FC: VIBRATION (SINUSOIDAL) |
EN 61000-4-2:2009 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
DIN EN 60068-2-14 : 2010 | ENVIRONMENTAL TESTING - PART 2-14: TESTS - TEST N: CHANGE OF TEMPERATURE |
ISO 14121-1:2007 | Safety of machinery Risk assessment Part 1: Principles |
ISO 6431:1992 | Pneumatic fluid power Single rod cylinders, 1 000 kPa (10 bar) series, with detachable mountings, bores from 32 mm to 320 mm Mounting dimensions |
EN 61000-4-3 : 2006 AMD 2 2010 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-3: TESTING AND MEASUREMENT TECHNIQUES - RADIATED, RADIO-FREQUENCY, ELECTROMAGNETIC FIELD IMMUNITY TEST |
IEC 60068-2-3:1969 | Basic environmental testing procedures - Part 2-3: Tests - Test Ca: Damp heat, steady state |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
IEC 61000-4-2:2008 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV | Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test |
IEC 60439-1:1999+AMD1:2004 CSV | Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies |
EN ISO 14122-2:2016 | Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016) |
ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
DIN EN 60068-2-78 : 2014 | ENVIRONMENTAL TESTING - PART 2-78: TESTS - TEST CAB: DAMP HEAT, STEADY STATE (IEC 60068-2-78:2012) |
ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
EN 60439-1:1999/A1:2004 | LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1 - TYPE TESTED AND PARTIALLY TYPE TESTED ASSEMBLIES |
EN 983:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics |
EN 954-1 : 1996 | SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN |
ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
EN 61000-4-4:2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST (IEC 61000-4-4:2012) |
IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
EN ISO 7250 : 1997 | BASIC HUMAN BODY MEASUREMENTS FOR TECHNOLOGICAL DESIGN |
EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
ISO 14122-2:2016 | Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways |
IEC 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.