DIN EN 1760-3:2009-07
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 3: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE BUMPERS, PLATES, WIRES AND SIMILAR DEVICES
Hardcopy , PDF
01-12-2013
English
01-01-2009
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Vorwort
Einleitung
1 Anwendungsbereich
2 Normative Verweisungen
3 Begriffe
4 Anforderungen
4.1 Allgemeines
4.2 Grundlegende Anforderungen
4.3 Spezifische Anforderungen an
Schaltpuffer
4.4 Zusätzliche Anforderungen
für Schaltflächen
4.5 Zusätzliche Anforderungen
für Schaltleinen
5 Kennzeichnung
5.1 Allgemeines
5.2 Schilder
5.3 Referenznummer
6 Informationen für Auswahl und
Anwendung
6.1 Allgemeines
6.2 Wesentliche Daten zur Auswahl einer
geeigneten Einrichtung
6.3 Benutzerinformation
7 Prüfung
7.1 Prüfung von Anforderungen, anwendbar
auf alle druckempfindlichen Schutzeinrichtungen,
die in diesem Teil von EN 1760 behandelt werden
7.2 Prüfung von Anforderungen nur für
Schaltpuffer
7.3 Prüfung von Anforderungen nur für
Schaltflächen
7.4 Prüfung von Anforderungen für Schaltleinen
7.5 Andere Prüfungen
Anhang A (normativ) Zeitdiagramme
Anhang B (informativ) Erläuternde Anmerkungen
zu den Charakteristika der Schutzeinrichtung
Anhang C (informativ) Anmerkungen zur Konstruktion
C.1 Allgemeines
C.2 Schaltpuffer
C.3 Schaltflächen
C.4 Schaltleinen
Anhang D (informativ) Allgemeine Anmerkungen zur
Anwendung
D.1 Allgemeines
D.2 Anwendung des Signalgebers
D.3 Signalgeberbefestigung
D.4 Anordnung des Signalgebers
D.5 Vom Signalgeber abgegebene Kraft
Anhang E (informativ) Anmerkungen zur
Inbetriebnahme und Prüfung
E.1 Allgemeines
E.2 Systeminformation
E.3 Inbetriebnahme
E.4 Regelmässige Inspektion und Prüfungen
E.5 Sicht- und Funktionsprüfungen nach Wartung
Anhang ZA (informativ) Zusammenhang zwischen
dieser Europäischen Norm und den grundlegenden
Anforderungen der EG-Richtlinie 98/37/EG
Anhang ZB (informativ) Zusammenhang zwischen dieser
Europäischen Norm und den grundlegenden
Anforderungen der EG-Richtlinie 2006/42/EG
Literaturhinweise
Proves the requirements for pressure sensitive protective devices which are not specified in EN 1760-1 and EN 1760-2.
| DocumentType |
Standard
|
| Pages |
69
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NF EN 1760-3 : 2004 + A1 2009 | Identical |
| NBN EN 1760-3 : 2004 + A1 2009 | Identical |
| NEN EN 1760-3 : 2004 + A1 2009 | Identical |
| NS EN 1760-3 : 2004 + A1 2009 | Identical |
| I.S. EN 1760-3:2004 | Identical |
| UNE-EN 1760-3:2005 | Identical |
| SN EN 1760-3 : 2004 + A1 2009 | Identical |
| UNI EN 1760-3 : 2009 | Identical |
| BS EN 1760-3 : 2004 | Identical |
| EN 1760-3:2004+A1:2009 | Identical |
| EN 418 : 1992 | SAFETY OF MACHINERY - EMERGENCY STOP EQUIPMENT, FUNCTIONAL ASPECTS - PRINCIPLES FOR DESIGN |
| EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
| EN 60947-5-5 : 1997 AMD 2 2016 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-5: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTRICAL EMERGENCY STOP DEVICE WITH MECHANICAL LATCHING FUNCTION (IEC 60947-5-5:1997/A2:2016) |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| IEC 61000-6-2:2016 | Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments |
| EN ISO 14121-1:2007 | Safety of machinery - Risk assessment - Part 1: Principles (ISO 14121-1:2007) |
| EN 999:1998+A1:2008 | Safety of machinery - The positioning of protective equipment in respect of approach speeds of parts of the human body |
| 1989/336/EEC : 1989 | COUNCIL DIRECTIVE OF 3 MAY 1989 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO ELECTROMAGNETIC COMPATIBILITY |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| IEC 61000-4-4:2012 RLV | Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test |
| EN 1760-1:1997+A1:2009 | Safety of machinery - Pressure sensitive protective devices - Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors |
| EN 61000-4-2:2009 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| ISO 14121-1:2007 | Safety of machinery Risk assessment Part 1: Principles |
| IEC 61000-4-6:2013 | Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields |
| EN 61000-4-3 : 2006 AMD 2 2010 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-3: TESTING AND MEASUREMENT TECHNIQUES - RADIATED, RADIO-FREQUENCY, ELECTROMAGNETIC FIELD IMMUNITY TEST |
| EN 61000-6-2:2005/corrigendum:2005 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS (IEC 61000-6-2:2005) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| IEC 61000-4-2:2008 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV | Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test |
| EN 62061:2005/A2:2015 | SAFETY OF MACHINERY - FUNCTIONAL SAFETY OF SAFETY-RELATED ELECTRICAL, ELECTRONIC AND PROGRAMMABLE ELECTRONIC CONTROL SYSTEMS (IEC 62061:2005/A2:2015) |
| EN 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| IEC 60439-1:1999+AMD1:2004 CSV | Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies |
| ISO 13849-2:2012 | Safety of machinery — Safety-related parts of control systems — Part 2: Validation |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| EN 60439-1:1999/A1:2004 | LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1 - TYPE TESTED AND PARTIALLY TYPE TESTED ASSEMBLIES |
| EN 60068-2-29:1993 | Environmental testing - Part 2: Tests - Test Eb and guidance: Bump |
| EN 60068-2-78:2013 | Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state |
| EN ISO 13849-2:2012 | Safety of machinery - Safety-related parts of control systems - Part 2: Validation (ISO 13849-2:2012) |
| EN 60068-2-6:2008 | Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
| EN 983:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics |
| EN 954-1 : 1996 | SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| EN 61000-4-4:2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST (IEC 61000-4-4:2012) |
| IEC 60068-2-29:1987 | Environmental testing. Part 2: Tests. Test Eb and guidance: Bump |
| EN 1760-2:2001+A1:2009 | Safety of machinery - Pressure sensitive protective devices - Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars |
| EN 61000-4-6:2014/AC:2015 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS (IEC 61000-4-6:2013) |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| IEC 62061:2005+AMD1:2012+AMD2:2015 CSV | Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems |
| 1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
| IEC 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| EN 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| IEC 60947-5-5:1997+AMD1:2005+AMD2:2016 CSV | Low-voltage switchgear and controlgear - Part 5-5: Control circuitdevices and switching elements - Electrical emergency stop device with mechanical latching function |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.