EN 10346:2015
Current
The latest, up-to-date edition.
Continuously hot-dip coated steel flat products for cold forming - Technical delivery conditions
15-07-2015
European foreword
1 Scope
2 Normative References
3 Terms and definitions
4 Classification and designation
5 Information to be supplied by the purchaser
6 Manufacturing and processing
7 Requirements
8 Inspection
9 Marking
10 Packing
11 Storage and transportation
Annex A (normative) - Reference method for determination
of the zinc, zinc-iron, zinc-aluminium, zinc-magnesium
and aluminium-zinc coating mass
Annex B (normative) - Reference method for determination
of the aluminium-silicon coating mass
Annex C (normative) - Method for determination of the mass
of the Al-Fe-Si alloy layer
Annex D (informative) - Technical changes from the previous
edition
Bibliography
This European Standard specifies requirements for continuously hot-dip coated products made of low carbon steels for cold forming, of steels for construction, of steels with high proof strength for cold forming and coated with zinc (Z), zinc-iron alloy (ZF), zinc-aluminium alloy (ZA), aluminium-zinc alloy (AZ), aluminium-silicon alloy (AS) or zinc-magnesium alloy (ZM) and for continuously hot-dip coated products made of multiphase steels for cold forming coated with zinc (Z), zinc-iron alloy (ZF), zinc-aluminium alloy (ZA) or zinc-magnesium alloy (ZM) in thicknesses of 0,20 mm ≤ t < 3,0 mm.
By agreement at the time of enquiry and order, this European Standard is applicable to continuously hot-dip coated flat products of an expanded validity range defined for thicknesses t < 0,20mm or in thicknesses 3,0mm < t < 6,5mm with agreed mechanical properties and test specimens, adhesion of coating and surface condition requirements.
The thickness is the final thickness of the delivered product after coating.
This document applies to strip of all widths and to sheets cut from it (≥ 600 mm width) and cut lengths
(< 600 mm width).
NOTE 1Products coated with (pure) aluminium can also be available, but are not covered by this European standard.
NOTE 2The products covered by this European Standard are used where cold formability, high strength, a defined minimum yield strength and corrosion resistance are the most important factors. Corrosion resistance of the product is proportional to the coating thickness, hence to its mass (see also 7.3.2). The products covered by this European Standard can be used as substrates for organic coated flat products specified in EN 10169 for building and general engineering applications.
NOTE 3By agreement at the time of enquiry and order, this European standard is applicable to other continuously hot-dip coated hot rolled steel flat products (e.g. in accordance with EN 10149-2).
Committee |
CEN/TC 459/SC 9
|
DevelopmentNote |
Supersedes EN 10292, EN 10326 and EN 10327. Together with EN 10152 supersedes EN 10336. (03/2009) Supersedes FORD WSD M1A295 A1/A2/A3 & FORD WSA M1A297 A1. (12/2014) Supersedes PREN 10346. (07/2015)
|
DocumentType |
Standard
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Current
|
Supersedes |
Standards | Relationship |
UNI EN 10346:2015 | Identical |
I.S. EN 10346:2015 | Identical |
PN EN 10346 : 2015 | Identical |
DIN EN 10346:2015-10 | Identical |
NEN EN 10346 : 2015 | Identical |
BS EN 10346:2015 | Identical |
UNE-EN 10346:2015 | Identical |
NF EN 10346 : 2015 | Identical |
NBN EN 10346 : 2015 | Identical |
UNI EN 10346 : 2009 | Identical |
SN EN 10346:2015 | Identical |
NS EN 10346 : 2015 | Identical |
PREN 13658-2 : DRAFT 2017 | METAL LATH AND BEADS - DEFINITIONS, REQUIREMENTS AND TEST METHODS - PART 2: EXTERNAL RENDERING |
BS ISO 9364:2017 | Steel sheet, 55 % aluminium-zinc alloy-coated by the continuous hot-dip process, of commercial, drawing and structural qualities |
17/30355209 DC : 0 | BS EN ISO 18592 - RESISTANCE WELDING - DESTRUCTIVE TESTING OF WELDS - METHOD FOR THE FATIGUE TESTING OF MULTI-SPOT-WELDED SPECIMENS |
BS EN 14509:2013 | Self-supporting double skin metal faced insulating panels. Factory made products. Specifications |
DIN EN 10152:2009-07 | ELECTROLYTICALLY ZINC COATED COLD ROLLED STEEL FLAT PRODUCTS FOR COLD FORMING - TECHNICAL DELIVERY CONDITIONS |
DIN EN 13381-5:2015-02 | TEST METHODS FOR DETERMINING THE CONTRIBUTION TO THE FIRE RESISTANCE OF STRUCTURAL MEMBERS - PART 5: APPLIED PROTECTION TO CONCRETE/PROFILED SHEET STEEL COMPOSITE MEMBER |
I.S. EN ISO 14713-2:2009 | ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 2: HOT DIP GALVANIZING |
EN 15773:2018 | Industrial application of powder organic coatings to hot dip galvanized or sherardized steel articles [duplex systems] - Specifications, recommendations and guidelines |
13/30280536 DC : 0 | BS ISO 4998 - CONTINUOUS HOT-DIP ZINC-COATED CARBON STEEL SHEET OF STRUCTURAL QUALITY |
UNI EN 13381-5 : 2014 | TEST METHODS FOR DETERMINING THE CONTRIBUTION TO THE FIRE RESISTANCE OF - STRUCTURAL MEMBERS - PART 5: APPLIED PROTECTION TO CONCRETE/PROFILED SHEET STEEL COMPOSITE MEMBER |
12/30265747 DC : 0 | BS EN 845-2 - SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS |
FD CEN/TR 16239 : 2011 FD | INSTALLATION RULES OF FIBROUS (GYPSUM) PLASTER WORKS |
15/30320416 DC : 0 | BS EN 1090-2 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
11/30251991 DC : 0 | BS EN 14195 - METAL FRAMING COMPONENTS FOR GYPSUM PLASTERBOARD SYSTEMS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
BS EN 16475-3 : 2016 | CHIMNEYS - ACCESSORIES - PART 3: DRAUGHT REGULATORS, STANDSTILL OPENING DEVICES AND COMBINED SECONDARY AIR DEVICES - REQUIREMENTS AND TEST METHODS |
DIN EN 14509:2013-12 | SELF-SUPPORTING DOUBLE SKIN METAL FACED INSULATING PANELS - FACTORY MADE PRODUCTS - SPECIFICATIONS |
12/30265759 DC : 0 | BS EN 845-3 - SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 3: BED JOINT REINFORCEMENT OF STEEL MESHWORK |
PREN 14353 : DRAFT 2016 | METAL BEADS AND FEATURE PROFILES FOR USE WITH GYPSUM PLASTERBOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
PREN 845-1 : DRAFT 2012 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS |
12/30265756 DC : 0 | BS EN 845-1 - SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS |
17/30357663 DC : 0 | BS ISO 5000 - STEEL SHEET, ALUMINIUM-SILICON ALLOY-COATED BY THE CONTINUOUS HOT-DIP PROCESS, OF COMMERCIAL AND DRAWING QUALITIES |
PREN 13658-1 : DRAFT 2017 | METAL LATH AND BEADS - DEFINITIONS, REQUIREMENTS AND TEST METHODS - PART 1: INTERNAL PLASTERING |
PREN 16002 : DRAFT 2016 | FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF THE RESISTANCE TO WIND LOAD OF MECHANICALLY FASTENED FLEXIBLE SHEETS FOR ROOF WATERPROOFING |
PREN 12574-2 : DRAFT 2015 | STATIONARY WASTE CONTAINERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS |
15/30323520 DC : 0 | BS EN 12574-2 - STATIONARY WASTE CONTAINERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS |
BS EN 10169 : 2010 | CONTINUOUSLY ORGANIC COATED (COIL COATED) STEEL FLAT PRODUCTS - TECHNICAL DELIVERY CONDITIONS |
UNE-EN 1317-5:2008 | Road restraint systems - Part 5: Product requirements and evaluation of conformity for vehicle restraint systems |
DIN EN 16002:2016-10 (Draft) | FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF THE RESISTANCE TO WIND LOAD OF MECHANICALLY FASTENED FLEXIBLE SHEETS FOR ROOF WATERPROOFING |
I.S. EN 10169:2010 | CONTINUOUSLY ORGANIC COATED (COIL COATED) STEEL FLAT PRODUCTS - TECHNICAL DELIVERY CONDITIONS |
BS EN 14353 : 2007 | METAL BEADS AND FEATURE PROFILES FOR USE WITH GYPSUM PLASTERBOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
UNI EN 912 : 2011 | TIMBER FASTENERS - SPECIFICATIONS FOR CONNECTORS FOR TIMBER |
I.S. EN 16002:2010 | FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF THE RESISTANCE TO WIND LOAD OF MECHANICALLY FASTENED FLEXIBLE SHEETS FOR ROOF WATERPROOFING |
BS EN ISO 18592:2009 | Resistance welding. Destructive testing of welds. Method for the fatigue testing of multispot- welded specimens |
DIN EN 12574-2:2015-08 (Draft) | STATIONARY WASTE CONTAINERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS |
DIN EN 1317-5:2012-06 | ROAD RESTRAINT SYSTEMS - PART 5: PRODUCT REQUIREMENTS AND EVALUATION OF CONFORMITY FOR VEHICLE RESTRAINT SYSTEMS |
BS EN 845-2 : 2013 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS |
BS EN 912:2011 | Timber fasteners. Specifications for connectors for timbers |
BS EN 1995-1-1 : 2012 | EUROCODE 5: DESIGN OF TIMBER STRUCTURES - PART 1-1: GENERAL - COMMON RULES AND RULES FOR BUILDINGS |
UNE-EN 505:2013 | Roofing products from metal sheet - Specification for fully supported roofing products of steel sheet |
BS EN 505:2013 | Roofing products from metal sheet. Specification for fully supported roofing products of steel sheet |
I.S. EN 912:2011 | TIMBER FASTENERS - SPECIFICATIONS FOR CONNECTORS FOR TIMBERS |
I.S. EN 13914-1:2016 | DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 1: EXTERNAL RENDERING |
DIN EN 14195:2015-03 | METAL FRAMING COMPONENTS FOR GYPSUM BOARD SYSTEMS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
DIN EN 508-1:2000-12 | ROOFING AND CLADDING PRODUCTS FROM METAL SHEET - SPECIFICATION FOR SELF-SUPPORTING OF STEEL, ALUMINIUM OR STAINLESS STEEL SHEET - PART 1: STEEL |
EN 12574-2:2017 | Stationary waste containers - Part 2: Performance requirements and test methods |
EN 10152:2017 | Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions |
EN 1075:2014 | Timber structures - Test methods - Joints made with punched metal plate fasteners |
DIN EN 1090-2:2011-10 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
UNI EN 508-1 : 2014 | ROOFING AND CLADDING PRODUCTS FROM METAL SHEET - SPECIFICATION FOR SELF-SUPPORTING OF STEEL, ALUMINIUM OR STAINLESS STEEL SHEET - PART 1: STEEL |
EN 13438:2013 | Paints and varnishes - Powder organic coatings for hot dip galvanised or sherardised steel products for construction purposes |
EN 10169:2010+A1:2012 | Continuously organic coated (coil coated) steel flat products - Technical delivery conditions |
EN 13381-5:2014 | Test methods for determining the contribution to the fire resistance of structural members - Part 5: Applied protection to concrete/profiled sheet steel composite member |
I.S. EN 16475-2:2017 | CHIMNEYS - ACCESSORIES - PART 2: CHIMNEY FANS - REQUIREMENTS AND TEST METHODS |
13/30266550 DC : 0 | BS EN 14509 - SELF-SUPPORTING DOUBLE SKIN METAL FACED INSULATING PANELS - FACTORY MADE PRODUCTS - SPECIFICATIONS |
13/30265753 DC : 0 | BS EN 13914-2 - DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 2: DESIGN CONSIDERATIONS AND ESSENTIAL PRINCIPLES FOR INTERNAL PLASTERING |
17/30334103 DC : 0 | BS ISO 9364 - CONTINUOUS HOT-DIP 55% ALUMINIUM/ZINC ALLOY-COATED STEEL SHEET OF COMMERCIAL, DRAWING AND STRUCTURAL QUALITIES |
PREN 1317-5 : DRAFT 2013 | ROAD RESTRAINT SYSTEMS - PART 5: PRODUCT REQUIREMENTS, TEST AND ASSESSMENT METHODS AND ACCEPTANCE CRITERIA |
15/30327671 DC : 0 | BS EN 10152 - ELECTROLYTICALLY ZINC COATED COLD ROLLED STEEL FLAT PRODUCTS FOR COLD FORMING - TECHNICAL DELIVERY CONDITIONS |
17/30337809 DC : DRAFT JAN 2017 | BS EN 15512 - STEEL STATIC STORAGE SYSTEMS - ADJUSTABLE PALLET RACKING SYSTEMS - PRINCIPLES FOR STRUCTURAL DESIGN |
PREN 1090-2 : DRAFT 2015 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
UNE-EN 1090-2:2011 | Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures |
PREN 14783 : DRAFT 2012 | FULLY SUPPORTED METAL SHEET AND STRIP FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS |
ISO 9364:2017 | Steel sheet, 55 % aluminium-zinc alloy-coated by the continuous hot-dip process, of commercial, drawing and structural qualities |
EN 16002:2010 | Flexible sheets for waterproofing - Determination of the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing |
UNI EN ISO 14713-2 : 2010 | ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 2: HOT DIP GALVANIZING |
BS EN 1090-2 : 2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
DIN EN 1090-2:2015-07 (Draft) | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
UNI EN 1090-2 : 2011 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
I.S. EN 14353:2017 | METAL BEADS AND FEATURE PROFILES FOR USE WITH GYPSUM PLASTERBOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
EN ISO 14713-2:2009 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 2: Hot dip galvanizing (ISO 14713-2:2009) |
ISO 4998:2014 | Continuous hot-dip zinc-coated and zinc-iron alloy-coated carbon steel sheet of structural quality |
DIN EN 1075:2015-03 | TIMBER STRUCTURES - TEST METHODS - JOINTS MADE WITH PUNCHED METAL PLATE FASTENERS |
DIN EN 13438:2013-12 | PAINTS AND VARNISHES - POWDER ORGANIC COATINGS FOR HOT DIP GALVANISED OR SHERARDISED STEEL PRODUCTS FOR CONSTRUCTION PURPOSES |
DIN EN 505:2013-06 | ROOFING PRODUCTS FROM METAL SHEET - SPECIFICATION FOR FULLY SUPPORTED ROOFING PRODUCTS OF STEEL SHEET |
BS EN 14195:2014 | Metal framing components for gypsum board systems. Definitions, requirements and test methods |
BS EN 13914-2:2016 | Design, preparation and application of external rendering and internal plastering Internal plastering |
BS EN 12574-2:2017 | Stationary waste containers Performance requirements and test methods |
BS EN ISO 1514:2004 | Paints and varnishes. Standard panels for testing |
I.S. EN 12574-2:2017 | STATIONARY WASTE CONTAINERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS |
I.S. EN 1317-5:2007 | ROAD RESTRAINT SYSTEMS - PART 5: PRODUCT REQUIREMENTS AND EVALUATION OF CONFORMITY FOR VEHICLE RESTRAINT SYSTEMS |
DIN EN 12574-2:2017-05 | STATIONARY WASTE CONTAINERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS |
EN 508-1:2014 | Roofing and cladding products from metal sheet - Specification for self-supporting of steel, aluminium or stainless steel sheet - Part 1: Steel |
I.S. EN 10152:2017 | ELECTROLYTICALLY ZINC COATED COLD ROLLED STEEL FLAT PRODUCTS FOR COLD FORMING - TECHNICAL DELIVERY CONDITIONS |
DIN EN 13611:2019-06 | Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements |
I.S. EN 505:2013 | ROOFING PRODUCTS FROM METAL SHEET - SPECIFICATION FOR FULLY SUPPORTED ROOFING PRODUCTS OF STEEL SHEET |
I.S. EN 14783:2013 | FULLY SUPPORTED METAL SHEET AND STRIP FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS |
I.S. EN 845-2:2013 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS |
I.S. EN 508-1:2014 | ROOFING AND CLADDING PRODUCTS FROM METAL SHEET - SPECIFICATION FOR SELF-SUPPORTING OF STEEL, ALUMINIUM OR STAINLESS STEEL SHEET - PART 1: STEEL |
I.S. EN 13438:2013 | PAINTS AND VARNISHES - POWDER ORGANIC COATINGS FOR HOT DIP GALVANISED OR SHERARDISED STEEL PRODUCTS FOR CONSTRUCTION PURPOSES |
I.S. EN 845-3:2013 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 3: BED JOINT REINFORCEMENT OF STEEL MESHWORK |
I.S. EN 14195:2014 | METAL FRAMING COMPONENTS FOR GYPSUM BOARD SYSTEMS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
I.S. EN 1075:2014 | TIMBER STRUCTURES - TEST METHODS - JOINTS MADE WITH PUNCHED METAL PLATE FASTENERS |
I.S. EN 13914-2:2016 | DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 2: INTERNAL PLASTERING |
I.S. EN ISO 1514:2016 | PAINTS AND VARNISHES - STANDARD PANELS FOR TESTING (ISO 1514:2016) |
I.S. EN 13964:2014 | SUSPENDED CEILINGS - REQUIREMENTS AND TEST METHODS |
I.S. EN 845-1:2013 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS |
DIN EN ISO 18592:2010-05 | RESISTANCE WELDING - DESTRUCTIVE TESTING OF WELDS - METHOD FOR THE FATIGUE TESTING OF MULTI-SPOT-WELDED SPECIMENS |
DIN EN 10169:2012-06 | Continuously organic coated (coil coated) steel flat products - Technical delivery conditions (includes Amendment A1:2012) |
12/30264367 DC : 0 | BS EN 505 - ROOFING PRODUCTS FROM METAL SHEET - SPECIFICATION FOR FULLY SUPPORTED ROOFING PRODUCTS OF STEEL SHEET |
I.S. EN 15773:2018 | INDUSTRIAL APPLICATION OF POWDER ORGANIC COATINGS TO HOT DIP GALVANIZED OR SHERARDIZED STEEL ARTICLES [DUPLEX SYSTEMS] - SPECIFICATIONS, RECOMMENDATIONS AND GUIDELINES |
12/30264370 DC : 0 | BS EN 14783 - FULLY SUPPORTED METAL SHEET AND STRIP FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS |
16/30323507 DC : 0 | BS EN 15773 - INDUSTRIAL APPLICATION OF POWDER ORGANIC COATINGS TO HOT DIP GALVANIZED OR SHERARDIZED STEEL ARTICLES [DUPLEX SYSTEMS] - SPECIFICATIONS, RECOMMENDATIONS AND GUIDELINES |
11/30234437 DC : 0 | BS ISO 9364 - CONTINUOUS HOT-DIP 55% ALUMINIUM/ZINC ALLOY-COATED STEEL SHEET OF COMMERCIAL, DRAWING AND STRUCTURAL QUALITIES |
PREN 14782 : DRAFT 2015 | SELF-SUPPORTING METAL SHEET FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS |
12/30265304 DC : 0 | BS EN 124-3 - GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 3: GULLY TOPS AND MANHOLE TOPS MADE FROM STEEL OR ALUMINIUM ALLOY |
BS EN ISO 14713-2:2009 | Zinc coatings. Guidelines and recommendations for the protection against corrosion of iron and steel in structures Hot dip galvanizing |
UNE-EN 13381-5:2016 | Test methods for determining the contribution to the fire resistance of structural members - Part 5: Applied protection to concrete/profiled sheet steel composite member |
CEN/TR 16239:2011 | Installation rules of fibrous (gypsum) plaster works |
14/30297831 DC : 0 | BS EN 1090-4 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 4: TECHNICAL REQUIREMENTS FOR THIN-GAUGE, COLD-FORMED STEEL ELEMENTS AND STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS |
PREN 14509 : DRAFT 2013 | SELF-SUPPORTING DOUBLE SKIN METAL FACED INSULATING PANELS - FACTORY MADE PRODUCTS - SPECIFICATIONS |
PREN 505 : DRAFT 2012 | ROOFING PRODUCTS FROM METAL SHEET - SPECIFICATION FOR FULLY SUPPORTED ROOFING PRODUCTS OF STEEL SHEET |
UNI EN 16002 : 2010 | FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF THE RESISTANCE TO WIND LOAD OF MECHANICALLY FASTENED FLEXIBLE SHEETS FOR ROOF WATERPROOFING |
EN 1090-2:2008+A1:2011 | Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures |
UNE-EN ISO 14713-2:2011 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 2: Hot dip galvanizing (ISO 14713-2:2009) |
UNE-EN 14353:2017 | Metal beads and feature profiles for use with gypsum plasterboards - Definitions, requirements and test methods |
PREN 1090-4 : DRAFT 2014 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 4: TECHNICAL REQUIREMENTS FOR THIN-GAUGE, COLD-FORMED STEEL ELEMENTS AND STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS |
ISO 5000:2011 | Continuous hot-dip aluminium-silicon-coated cold-reduced carbon steel sheet of commercial and drawing qualities |
I.S. EN 14509:2013 | SELF-SUPPORTING DOUBLE SKIN METAL FACED INSULATING PANELS - FACTORY MADE PRODUCTS - SPECIFICATIONS |
DIN EN 508-1:2014-08 | Roofing and cladding products from metal sheet - Specification for self-supporting of steel, aluminium or stainless steel sheet - Part 1: Steel |
DIN EN 13914-1:2016-09 | DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 1: EXTERNAL RENDERING |
DIN EN 13914-2:2016-09 | DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 2: INTERNAL PLASTERING |
DIN EN 13964:2014-08 | SUSPENDED CEILINGS - REQUIREMENTS AND TEST METHODS |
UNE-EN 14509:2014 | Self-supporting double skin metal faced insulating panels - Factory made products - Specifications |
EN 13914-1:2016 | Design, preparation and application of external rendering and internal plastering - Part 1: External rendering |
EN 13964:2014 | Suspended ceilings - Requirements and test methods |
UNI EN 14509 : 2013 | SELF-SUPPORTING DOUBLE SKIN METAL FACED INSULATING PANELS - FACTORY MADE PRODUCTS - SPECIFICATIONS |
UNI EN 14783 : 2013 | FULLY SUPPORTED METAL SHEET AND STRIP FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS |
UNI EN 505 : 2013 | ROOFING PRODUCTS FROM METAL SHEET - SPECIFICATION FOR FULLY SUPPORTED ROOFING PRODUCTS OF STEEL SHEET |
UNI EN 1317-5 : 2012 | ROAD RESTRAINT SYSTEMS - PART 5: PRODUCT REQUIREMENTS AND EVALUATION OF CONFORMITY FOR VEHICLE RESTRAINT SYSTEMS |
UNI EN 13964 : 2014 | SUSPENDED CEILINGS - REQUIREMENTS AND TEST METHODS |
UNI EN 13438 : 2013 | PAINTS AND VARNISHES - POWDER ORGANIC COATINGS FOR HOT DIP GALVANISED OR SHERARDIZED STEEL PRODUCTS FOR CONSTRUCTION PURPOSES |
UNI EN 1995-1-1 : 2014 | EUROCODE 5 - DESIGN OF TIMBER STRUCTURES - PART 1-1: GENERAL - COMMON RULES AND RULES FOR BUILDINGS |
17/30357430 DC | BS EN 13658-2. Metal lath and beads. Definitions, requirements and test methods. Part 2. External rendering |
DIN EN 16475-2:2013-08 (Draft) | CHIMNEYS - ACCESSORIES - PART 2: CHIMNEY FANS - REQUIREMENTS AND TEST METHODS |
UNI EN ISO 18592 : 2010 | RESISTANCE WELDING - DESTRUCTIVE TESTING OF WELDS - METHOD FOR THE FATIGUE TESTING OF MULTI-SPOT-WELDED SPECIMENS |
PREN 13914-2 : DRAFT 2013 | DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 2: DESIGN CONSIDERATIONS AND ESSENTIAL PRINCIPLES FOR INTERNAL PLASTERING |
I.S. EN 1995-1-1:2005 | EUROCODE 5: DESIGN OF TIMBER STRUCTURES - PART 1-1: GENERAL - COMMON RULES AND RULES FOR BUILDINGS |
NF EN ISO 14713-2 : 2010 | ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 2: HOT DIP GALVANIZING |
I.S. EN 13381-5:2014 | TEST METHODS FOR DETERMINING THE CONTRIBUTION TO THE FIRE RESISTANCE OF STRUCTURAL MEMBERS - PART 5: APPLIED PROTECTION TO CONCRETE/PROFILED SHEET STEEL COMPOSITE MEMBER |
DIN EN 14353:2016-02 (Draft) | METAL BEADS AND FEATURE PROFILES FOR USE WITH GYPSUM PLASTERBOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
PREN 13438 : DRAFT 2012 | PAINTS AND VARNISHES - POWDER ORGANIC COATINGS FOR GALVANIZED OR SHERARDIZED STEEL PRODUCTS FOR CONSTRUCTION PURPOSES |
DIN EN 10152:2015-10 (Draft) | ELECTROLYTICALLY ZINC COATED COLD ROLLED STEEL FLAT PRODUCTS FOR COLD FORMING - TECHNICAL DELIVERY CONDITIONS |
14/30266796 DC : 0 | BS EN ISO 1514 - PAINTS AND VARNISHES - STANDARD PANELS FOR TESTING |
BS EN ISO 14713-1:2017 | Zinc coatings. Guidelines and recommendations for the protection against corrosion of iron and steel in structures General principles of design and corrosion resistance |
DIN EN ISO 14713-1:2010-05 | ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 1: GENERAL PRINCIPLES OF DESIGN AND CORROSION RESISTANCE (ISO 14713-1:2017) |
13/30217369 DC : 0 | BS EN 13964 - SUSPENDED CEILINGS - REQUIREMENTS AND TEST METHODS |
12/30258236 DC : 0 | BS EN 10358 - UNALLOYED STEEL PLUMBING FITTINGS - FITTINGS WITH PRESS ENDS FOR UNALLOYED STEEL TUBES |
PREN 14566 : DRAFT 2014 | MECHANICAL FASTENERS FOR GYPSUM BOARD SYSTEMS - DEFINITIONS, REQUIREMENTS AND TESTS METHODS |
BS ISO 3575:2011 | Continuous hot-dip zinc-coated carbon steel sheet of commercial and drawing qualities |
17/30357427 DC | BS EN 13658-1. Metal lath and beads. Definitions, requirements and test methods. Part 1. Internal plastering |
ISO 3575:2016 | Continuous hot-dip zinc-coated and zinc-iron alloy-coated carbon steel sheet of commercial and drawing qualities |
PREN 845-3 : DRAFT 2012 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 3: BED JOINT REINFORCEMENT OF STEEL MESHWORK |
PREN 845-2 : DRAFT 2012 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS |
UNE-EN 13611:2016 | Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements |
NF EN 16002 : 2010 | FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF THE RESISTANCE TO WIND LOAD OF MECHANICALLY FASTENED FLEXIBLE SHEETS FOR ROOF WATERPROOFING |
16/30346712 DC : 0 | BS EN 16002 - FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF THE RESISTANCE TO WIND LOAD OF MECHANICALLY FASTENED FLEXIBLE SHEETS FOR ROOF WATERPROOFING |
PREN 14195 : DRAFT 2011 | METAL FRAMING COMPONENTS FOR GYPSUM BOARD SYSTEMS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
I.S. EN 13611:2015 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
DIN EN 912:2011-09 | Timber fasteners - Specifications for connectors for timbers |
ISO 14713-2:2009 | Zinc coatings Guidelines and recommendations for the protection against corrosion of iron and steel in structures Part 2: Hot dip galvanizing |
BS EN 845-1 : 2013 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS |
BS EN 508-1:2014 | Roofing and cladding products from metal sheet. Specification for self-supporting of steel, aluminium or stainless steel sheet Steel |
ISO 14713-1:2017 | Zinc coatings — Guidelines and recommendations for the protection against corrosion of iron and steel in structures — Part 1: General principles of design and corrosion resistance |
BS EN 10152:2017 | Electrolytically zinc coated cold rolled steel flat products for cold forming. Technical delivery conditions |
BS EN 13914-1:2016 | Design, preparation and application of external rendering and internal plastering External rendering |
BS EN 845-3 : 2013 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 3: BED JOINT REINFORCEMENT OF STEEL ESHWORK |
UNE-EN ISO 1514:2017 | Paints and varnishes - Standard panels for testing (ISO 1514:2016) |
UNE-EN 14195:2015 | Metal framing components for gypsum board systems - Definitions, requirements and test methods |
UNE-EN 1995-1-1:2016 | Eurocode 5: Design of timber structures - Part 1-1: General - Common rules and rules for buildings. |
UNE-EN 10152:2017 | Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions |
BS EN 14783:2013 | Fully supported metal sheet and strip for roofing, external cladding and internal lining. Product specification and requirements |
DIN EN 14783:2013-07 | FULLY SUPPORTED METAL SHEET AND STRIP FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS |
BS EN 1075:2014 | Timber structures. Test methods. Joints made with punched metal plate fasteners |
BS EN 13438:2013 | Paints and varnishes. Powder organic coatings for hot dip galvanised or sherardised steel products for construction purposes |
UNE-EN 1075:2015 | Timber structures - Test methods - Joints made with punched metal plate fasteners |
ISO 18592:2009 | Resistance welding Destructive testing of welds Method for the fatigue testing of multi-spot-welded specimens |
UNE-EN 10169:2011 | Continuously organic coated (coil coated) steel flat products - Technical delivery conditions |
BS EN 1317-5 : 2007 | ROAD RESTRAINT SYSTEMS - PART 5: PRODUCT REQUIREMENTS AND EVALUATION OF CONFORMITY FOR VEHICLE RESTRAINT SYSTEMS |
EN 845-3:2013+A1:2016 | Specification for ancillary components for masonry - Part 3: Bed joint reinforcement of steel meshwork |
EN 845-2:2013+A1:2016 | Specification for ancillary components for masonry - Part 2: Lintels |
EN ISO 18592:2009 | Resistance welding - Destructive testing of welds - Method for the fatigue testing of multi-spot-welded specimens (ISO 18592:2009) |
EN 845-1:2013+A1:2016 | Specification for ancillary components for masonry - Part 1: Wall ties, tension straps, hangers and brackets |
EN 14509:2013 | Self-supporting double skin metal faced insulating panels - Factory made products - Specifications |
EN 505:2013 | Roofing products from metal sheet - Specification for fully supported roofing products of steel sheet |
EN ISO 14713-1:2017 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 1: General principles of design and corrosion resistance (ISO 14713-1:2017) |
EN ISO 1514:2016 | Paints and varnishes - Standard panels for testing (ISO 1514:2016) |
EN 14353:2017 | Metal beads and feature profiles for use with gypsum plasterboards - Definitions, requirements and test methods |
EN 16475-2:2017 | Chimneys - Accessories - Part 2: Chimney fans - Requirements and test methods |
EN 14195:2014 | Metal framing components for gypsum board systems - Definitions, requirements and test methods |
EN 912:2011 | Timber fasteners - Specifications for connectors for timbers |
EN 14783:2013 | Fully supported metal sheet and strip for roofing, external cladding and internal lining - Product specification and requirements |
EN 13914-2:2016 | Design, preparation and application of external rendering and internal plastering - Part 2: Internal plastering |
09/30207859 DC : 0 | BS EN 16002 - FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF THE RESISTANCE TO WIND LOAD OF MECHANICALLY FASTENED FLEXIBLE SHEETS FOR ROOF WATERPROOFING |
PD CEN/TR 16239:2011 | Installation rules of fibrous (gypsum) plaster works |
I.S. EN 16475-3:2016 | CHIMNEYS - ACCESSORIES - PART 3: DRAUGHT REGULATORS, STANDSTILL OPENING DEVICES AND COMBINED SECONDARY AIR DEVICES - REQUIREMENTS AND TEST METHODS |
12/30238456 DC : 0 | BS EN 13438 - PAINTS AND VARNISHES - POWDER ORGANIC COATINGS FOR GALVANIZED OR SHERARDIZED STEEL PRODUCTS FOR CONSTRUCTION PURPOSES |
BS EN 16475-2:2017 | Chimneys. Accessories Chimney fans. Requirements and test methods |
PREN 15773 : DRAFT 2016 | INDUSTRIAL APPLICATION OF POWDER ORGANIC COATINGS TO HOT DIP GALVANIZED OR SHERARDIZED STEEL ARTICLES [DUPLEX SYSTEMS] - SPECIFICATIONS, RECOMMENDATIONS AND GUIDELINES |
16/30332914 DC : 0 | BS EN 14353 - METAL BEADS AND FEATURE PROFILES FOR USE WITH GYPSUM PLASTERBOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
15/30312507 DC : 0 | BS ISO 3575 - CONTINUOUS HOT-DIP ZINC-COATED AND ZINC-IRON ALLOY-COATED CARBON STEEL SHEET OF COMMERCIAL AND DRAWING QUALITIES |
17/30360051 DC : 0 | BS EN 13611 - SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
BS EN 13381-5:2014 | Test methods for determining the contribution to the fire resistance of structural members Applied protection to concrete/profiled sheet steel composite member |
BS EN 13611:2015 | Safety and control devices for burners and appliances burning gaseous and/or liquid fuels. General requirements |
I.S. EN ISO 14713-1:2017 | ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 1: GENERAL PRINCIPLES OF DESIGN AND CORROSION RESISTANCE (ISO 14713-1:2017) |
UNE-EN ISO 14713-1:2017 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 1: General principles of design and corrosion resistance (ISO 14713-1:2017) |
BS EN 16002:2010 | Flexible sheets for waterproofing. Determination of the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing |
BS ISO 4998:2014 | Continuous hot-dip zinc-coated and zinc-iron alloy-coated carbon steel sheet of structural quality |
PREN 13964 : DRAFT 2013 | SUSPENDED CEILINGS - REQUIREMENTS AND TEST METHODS |
UNE-EN ISO 18592:2010 | Resistance welding - Destructive testing of welds - Method for the fatigue testing of multi-spot-welded specimens (ISO 18592:2009) |
I.S. EN 1090-2:2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
EN 16475-3:2016 | Chimneys - Accessories - Part 3: Draught regulators, standstill opening devices and combined secondary air devices - Requirements and test methods |
UNI EN 10169 : 2012 | CONTINUOUSLY ORGANIC COATED (COIL COATED) STEEL FLAT PRODUCTS - TECHNICAL DELIVERY CONDITIONS |
DIN EN 13611:2016-09 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
PREN 13611 : DRAFT 2017 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
I.S. EN ISO 18592:2009 | RESISTANCE WELDING - DESTRUCTIVE TESTING OF WELDS - METHOD FOR THE FATIGUE TESTING OF MULTI-SPOT-WELDED SPECIMENS |
UNE-EN 13964:2016 | Suspended ceilings - Requirements and test methods |
UNE-EN 912:2011 | Timber fasteners - Specifications for connectors for timbers |
UNE-EN 508-1:2014 | Roofing and cladding products from metal sheet - Specification for self-supporting of steel, aluminium or stainless steel sheet - Part 1: Steel |
UNE-EN 12574-2:2017 | Stationary waste containers - Part 2: Performance requirements and test methods |
BS EN 13964:2014 | Suspended ceilings. Requirements and test methods |
ISO 1514:2016 | Paints and varnishes — Standard panels for testing |
DIN EN 16002:2010-10 | FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF THE RESISTANCE TO WIND LOAD OF MECHANICALLY FASTENED FLEXIBLE SHEETS FOR ROOF WATERPROOFING |
DIN EN ISO 14713-2:2010-05 | ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 2: HOT DIP GALVANIZING |
I.S. EN 13611:2015/AC:2016 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
DIN EN 14353:2017-09 | METAL BEADS AND FEATURE PROFILES FOR USE WITH GYPSUM PLASTERBOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
ISO 10275:2007 | Metallic materials Sheet and strip Determination of tensile strain hardening exponent |
EN 10079:2007 | Definition of steel products |
EN 10027-2:2015 | Designation systems for steels - Part 2: Numerical system |
EN 10152:2017 | Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions |
EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
ISO 14713-1:2017 | Zinc coatings — Guidelines and recommendations for the protection against corrosion of iron and steel in structures — Part 1: General principles of design and corrosion resistance |
ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
EN 10149-2:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels |
EN 10169:2010+A1:2012 | Continuously organic coated (coil coated) steel flat products - Technical delivery conditions |
EN 10143:2006 | Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape |
EN 10021:2006 | General technical delivery conditions for steel products |
EN ISO 14713-1:2017 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 1: General principles of design and corrosion resistance (ISO 14713-1:2017) |
EN 10204:2004 | Metallic products - Types of inspection documents |
EN 10049:2013 | Measurement of roughness average Ra and peak count RPc on metallic flat products |
EN 10027-1:2016 | Designation systems for steels - Part 1: Steel names |
ISO 10113:2006 | Metallic materials Sheet and strip Determination of plastic strain ratio |
EN 10020:2000 | Definition and classification of grades of steel |
EN 606:2004 | Bar coding - Transport and handling labels for steel products |
ISO 14713-2:2009 | Zinc coatings Guidelines and recommendations for the protection against corrosion of iron and steel in structures Part 2: Hot dip galvanizing |
EN 10325:2006 | Steel - Determination of yield strength increase by the effect of heat treatment [Bake-Hardening-Index] |
EN ISO 14713-2:2009 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 2: Hot dip galvanizing (ISO 14713-2:2009) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.