EN 1093-11:2001+A1:2008
Current
Current
The latest, up-to-date edition.
Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 11: Decontamination index
Published date
09-07-2008
Publisher
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Determination of concentration measurement points
6 Test method
7 Application to specific group of machines
8 Influencing factors
9 Expression of results
10 Test report
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 98/37/EC
Annex ZB (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
This standard describes a method for the measurement of the decontami¬nation index of pollution con¬trol systems e. g. capture devices including local exhaust ventilation, water spray systems and, when appropriate, separation equipment installed on a machine. This method uses the real pollutant (see 4.2 of EN 1093-1 : 1998 “ Safety of machinery — Evaluation of the emission of airborne hazardous substances — Part 1: Selection of test methods”) and can be operated in room or field environments.It should be observed that during the test, especially during the shutdown or the removal of the pollution control system, the concentration of hazardous substances , if present, can reach levels which are liable to incur a risk to the health of the operators or other occupants present in the room.Warning: This standard does not deal with the protective measures required to control these risks.Measurement of the decontamination index of pollution control system can serve for the:–evaluation of the performance of a pollution control system of a machine;–evaluation of the improvement of a pollution control system;–comparison of pollution control systems for machines of similar design;–ranking of pollution control systems according to their decontamination efficiency;–determination of the air flow rate in the case of an exhaust system to achieve a given level;–determination of the state of the art of pollution control systems for machines with respect to the decontamina¬tion efficiency.
| Committee |
CEN/TC 114
|
| DevelopmentNote |
2001 Edition Re-Issued in July 2008 & incorporates AMD 1 2008. (07/2008)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Standards | Relationship |
| BS EN 1093-11 : 2001 | Identical |
| SN EN 1093-11 : 2001 + A1 2008 | Identical |
| UNI EN 1093-11 : 2008 | Identical |
| DIN EN 1093-11:2008-11 | Identical |
| NS EN 1093-11 : 2001 + A1 2008 | Identical |
| NBN EN 1093-11 : 2001 + A1 2008 | Identical |
| NEN EN 1093-11 : 2001 + A1 2008 | Identical |
| PN EN 1093-11 : 2005 + A1 2010 | Identical |
| I.S. EN 1093-11:2001 | Identical |
| UNE-EN 1093-11:2001 | Identical |
| NF EN 1093-11 : 2001 + A1 2008 | Identical |
| UNE-EN 1093-11:2001+A1:2008 | Identical |
| BS EN 1093-11:2001+A1:2008 | Identical |
| I.S. EN 691-1:2012 | SAFETY OF WOODWORKING MACHINES - PART 1: COMMON REQUIREMENTS |
| 12/30253910 DC : DRAFT JULY 2012 | BS EN 1807-2 - SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - LOG SAWING MACHINES |
| PREN 1870-3 : DRAFT 2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 3: DOWN CUTTING CROSS-CUT SAWS AND DUAL PURPOSE DOWN CUTTING CROSS-CUT SAWS/CIRCULAR SAW BENCHES |
| 11/30237569 DC : 0 | BS EN 1870-19 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 19: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE) AND BUILDING SITE SAWS |
| DIN EN 1807-1:2013-06 | Safety of woodworking machines - Band sawing machines - Part 1: Table band saws and band re-saws |
| I.S. EN ISO 18217:2015 | SAFETY OF WOODWORKING MACHINES - EDGE-BANDING MACHINES FED BY CHAIN(S) (ISO 18217:2015) |
| PREN 1870-12 : DRAFT 2011 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 12: PENDULUM CROSS-CUT SAWING MACHINES |
| I.S. EN 1807-2:2013 | SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - PART 2: LOG SAWING MACHINES |
| UNE-EN ISO 19085-1:2018 | Woodworking machines - Safety - Part 1: Common requirements (ISO 19085-1:2017) |
| DIN EN 1870-7:2013-01 | Safety of woodworking machines - Circular sawing machines - Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading |
| DIN EN 1870-12:2014-03 | Safety of woodworking machines - Circular sawing machines - Part 12: Pendulum cross-cut sawing machines |
| DIN EN 1870-16:2013-01 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V CUTTING |
| DIN EN 1870-9:2013-01 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 9: DOUBLE BLADE CIRCULAR SAWING MACHINES FOR CROSS-CUTTING WITH INTEGRATED FEED AND WITH MANUAL LOADING AND/OR UNLOADING |
| DIN EN 1870-3:2015-02 | Safety of woodworking machines - Circular sawing machines - Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches |
| I.S. EN 861:2007 | SAFETY OF WOODWORKING MACHINES - SURFACE PLANING AND THICKNESSING MACHINES |
| UNE-EN 1870-4:2012 | Safety of woodworking machines - Circular sawing machines - Part 4: Multiblade rip sawing machines with manual loading and/or unloading |
| BS EN 859 : 2007 | SAFETY OF WOODWORKING MACHINES - HAND FED SURFACE PLANING MACHINES |
| UNE-EN 1870-7:2013 | Safety of woodworking machines - Circular sawing machines - Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading |
| BS EN 1870-9:2012 | Safety of woodworking machines. Circular sawing machines Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading |
| BS EN 1870-15:2012 | Safety of woodworking machines. Circular sawing machines Multi-blade cross-cut sawing machines with integrated feed of the workpiece and manual loading and/or unloading |
| I.S. EN 1870-16:2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V-CUTTING |
| EN 1807-1:2013 | Safety of woodworking machines - Band sawing machines - Part 1: Table band saws and band re-saws |
| EN 1093-1:2008 | Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 1: Selection of test methods |
| 15/30302620 DC : 0 | BS EN ISO 19085-4 - WOODWORKING MACHINES - SAFETY - PART 4: VERTICAL PANEL CIRCULAR SAWING MACHINES |
| 12/30265270 DC : 0 | BS EN 1870-6 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 6: CIRCULAR SAWING MACHINES FOR FIREWOOD AND DUAL PURPOSE CIRCULAR SAWING MACHINES FOR FIREWOOD/CIRCULAR SAW BENCHES, WITH MANUAL LOADING AND/OR UNLOADING |
| 11/30237566 DC : 0 | BS EN 1870-18 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 18: DIMENSION SAWS |
| 07/30165769 DC : 0 | BS EN 1093-1 - SAFETY OF MACHINERY - EVALUATION OF THE EMISSION OF AIRBORNE HAZARDOUS SUBSTANCES - PART 1: SELECTION OF TEST METHODS |
| UNE-EN 1870-13:2008 | Safety of woodworking machines - Circular sawing machines - Part 13: Horizontal beam panel sawing machines |
| BS EN 1870-19:2013 | Safety of woodworking machines. Circular sawing machines Circular saw benches (with and without sliding table) and building site saws |
| UNI EN 1870-19 : 2014 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 19: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE) AND BUILDING SITE SAWS |
| 11/30237557 DC : 0 | BS EN 1870-11 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI-AUTOMATIC AND AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS) |
| DIN EN 1807-2:2013-06 | Safety of woodworking machines - Band sawing machines - Part 2: Log sawing machines; German version EN 1807-2:2013 |
| 12/30232434 DC : 0 | BS EN 1870-5:2002+A1:2009 AMD 2 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 5: CIRCULAR SAWBENCHES/UP-CUTTING CROSS-CUT SAWING MACHINES |
| UNE-EN 691-1:2013 | Safety of woodworking machines - Part 1: Common requirements |
| PREN 1870-11 : DRAFT 2011 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI-AUTOMATIC AND AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS) |
| 11/30244804 DC : 0 | BS EN 940:2009/A1 - SAFETY OF WOODWORKING MACHINES - COMBINED WOODWORKING MACHINES |
| PREN 1870-6 : DRAFT 2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 6: CIRCULAR SAWING MACHINES FOR FIREWOOD AND DUAL PURPOSE CIRCULAR SAWING MACHINES FOR FIREWOOD/CIRCULAR SAW BENCHES, WITH MANUAL LOADING AND/OR UNLOADING |
| DIN EN 1870-14:2012-06 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 14: VERTICAL PANEL SAWING MACHINES |
| DIN EN 1870-13:2013-07 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 13: HORIZONTAL BEAM PANEL SAWING MACHINES |
| DIN EN 1870-10:2013-07 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES |
| DIN EN 1870-8:2013-03 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 8: SINGLE BLADE EDGING CIRCULAR RIP SAWING MACHINES WITH POWER DRIVEN SAW UNIT AND MANUAL LOADING AND/OR UNLOADING |
| BS EN 1870-7:2012 | Safety of woodworking machines. Circular sawing machines Single blade log sawing machines with integrated feed table and manual loading and/or unloading |
| BS EN 940 : 2009 | SAFETY OF WOODWORKING MACHINES - COMBINED WOODWORKING MACHINES |
| UNE-EN 1870-10:2013 | Safety of woodworking machines - Circular sawing machines - Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines |
| I.S. EN 1870-8:2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 8: SINGLE BLADE EDGING CIRCULAR RIP SAWING MACHINES WITH POWER DRIVEN SAW UNIT AND MANUAL LOADING AND/OR UNLOADING |
| I.S. EN 1870-10:2013 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES |
| I.S. EN 1870-11:2013 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS) |
| I.S. EN 1870-12:2013 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 12: PENDULUM CROSS-CUT SAWING MACHINES |
| I.S. EN 1870-9:2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 9: DOUBLE BLADE CIRCULAR SAWING MACHINES FOR CROSSCUTTING WITH INTEGRATED FEED AND WITH MANUAL LOADING AND/OR UNLOADING |
| I.S. EN 1870-3:2014 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 3: DOWN CUTTING CROSS-CUT SAWS AND DUAL PURPOSE DOWN CUTTING CROSS-CUT SAWS/CIRCULAR SAW BENCHES |
| I.S. EN 1093-1:2008 | SAFETY OF MACHINERY - EVALUATION OF THE EMISSION OF AIRBORNE HAZARDOUS SUBSTANCES - PART 1: SELECTION OF TEST METHODS |
| I.S. EN 12750:2013 | SAFETY OF WOODWORKING MACHINES - FOUR SIDED MOULDING MACHINES |
| I.S. EN 1870-15:2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 15: MULTIBLADE CROSS-CUT SAWING MACHINES WITH INTEGRATED FEED OF THE WORKPIECE AND MANUAL LOADING AND/OR UNLOADING |
| I.S. EN 1870-17:2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 17: MANUAL HORIZONTAL CUTTING CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS) |
| I.S. EN 1870-14:2007 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 14: VERTICAL PANEL SAWING MACHINES |
| I.S. EN 940:2009 | SAFETY OF WOODWORKING MACHINES - COMBINED WOODWORKING MACHINES |
| I.S. EN 1870-5:2002 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 5: CIRCULAR SAWBENCHES/UP-CUTTING CROSS-CUT SAWING MACHINES |
| I.S. EN 1870-7:2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 7: SINGLE BLADE LOG SAWING MACHINES WITH INTEGRATED FEED TABLE AND MANUAL LOADING AND/OR UNLOADING |
| I.S. EN 1870-4:2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 4: MULTIBLADE RIP SAWING MACHINES WITH MANUAL LOADING AND/OR UNLOADING |
| UNI EN 940 : 2012 | SAFETY OF WOODWORKING MACHINES - COMBINED WOODWORKING MACHINES |
| UNI EN 691-1 : 2012 | SAFETY OF WOODWORKING MACHINES - PART 1: COMMON REQUIREMENTS |
| I.S. EN 848-1:2007 | SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 1: SINGLE SPINDLE VERTICAL MOULDING MACHINES |
| DIN EN ISO 18217:2015-12 | Safety of woodworking machines - Edge-banding machines fed by chain(s) (ISO 18217:2015) |
| 11/30231787 DC : 0 | BS EN 1870-14:2007+A1:2009/FPRA2 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 14: VERTICAL PANEL SAWING MACHINES |
| 10/30232428 DC : DRAFT DEC 2010 | BS EN 1870-16 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V CUTTING |
| BS EN 1870-18:2013 | Safety of woodworking machines. Circular sawing machines Dimension saws |
| 12/30253907 DC : DRAFT JULY 2012 | BS EN 1807-1 - SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - TABLE BAND SAWS AND BAND RE-SAWS |
| 10/30233212 DC : 0 | BS EN 848-3 - SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOLS - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES |
| BS EN 1807-2:2013 | Safety of woodworking machines. Band sawing machines Log sawing machines |
| 10/30232431 DC : DRAFT DEC 2010 | BS EN 1870-17 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 17: MANUAL HORIZONTAL CUTTING CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (MANUAL RADIAL ARM SAWS) |
| 14/30293310 DC : 0 | BS EN ISO 19085-1 - WOODWORKING MACHINES - SAFETY - PART 1: COMMON REQUIREMENTS |
| BS EN 1807-1:2013 | Safety of woodworking machines. Band sawing machines Table band saws and band re-saws |
| BS EN ISO 19085-1:2017 | Woodworking machines. Safety Common requirements |
| 11/30237563 DC : 0 | BS EN 1870-10 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES |
| UNE-EN 1807-1:2013 | Safety of woodworking machines - Band sawing machines - Part 1: Table band saws and band re-saws |
| UNI EN 1807-2 : 2013 | SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - PART 2: LOG SAWING MACHINES |
| PREN 1870-10 : DRAFT 2011 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES |
| UNE-EN 1870-14:2008 | Safety of woodworking machines - Circular sawing machines - Part 14: Vertical panel sawing machines |
| ISO/TR 18569:2004 | Safety of machinery Guidelines for the understanding and use of safety of machinery standards |
| DIN EN 1870-11:2014-02 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS) |
| DIN EN 12750:2013-05 | Safety of woodworking machines - Four sided moulding machines |
| DIN EN 1870-17:2015-06 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 17: MANUAL HORIZONTAL CUTTING CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS) |
| DIN EN 1870-15:2013-01 | Safety of woodworking machines - Circular sawing machines - Part 15: Multi-blade cross-cut sawing machines with integrated feed of the workpiece and manual loading and/or unloading |
| DIN EN 848-3:2013-01 | SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOLS - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES |
| DIN EN 860:2012-09 | SAFETY OF WOODWORKING MACHINES - ONE SIDE THICKNESS PLANING MACHINES |
| DIN EN 848-1:2013-01 | SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 1: SINGLE SPINDLE VERTICAL MOULDING MACHINES |
| DIN EN 848-2:2013-01 | SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 2: SINGLE SPINDLE HAND FED/INTEGRATED FED ROUTING MACHINES |
| BS EN 861 : 2007 | SAFETY OF WOODWORKING MACHINES - SURFACE PLANING AND THICKNESSING MACHINES |
| UNE-EN 1870-8:2013 | Safety of woodworking machines - Circular sawing machines - Part 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading |
| BS EN 848-2 : 2007 | SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 2: SINGLE SPINDLE HAND FED/INTEGRATED FED ROUTING MACHINES |
| UNE-EN 848-1:2008 | Safety of woodworking machines - One side moulding machines with rotating tool - Part 1: Single spindle vertical moulding machines |
| UNE-EN 848-3:2013 | Safety of woodworking machines - One side moulding machines with rotating tool - Part 3: Numerically controlled (NC) boring and routing machines |
| I.S. EN 848-2:2007 | SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 2: SINGLE SPINDLE HAND FED/INTEGRATED FED ROUTING MACHINES |
| EN 1870-15:2012 | Safety of woodworking machines - Circular sawing machines - Part 15: Multi-blade cross-cut sawing machines with integrated feed of the workpiece and manual loading and/or unloading |
| UNI EN 1870-13 : 2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 13: HORIZONTAL BEAM PANEL SAWING MACHINES |
| UNI EN 1870-8 : 2013 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 8: SINGLE BLADE EDGING CIRCULAR RIP SAWING MACHINES WITH POWER DRIVEN SAW UNIT AND MANUAL LOADING AND/OR UNLOADING |
| UNI EN 1093-1 : 2009 | SAFETY OF MACHINERY - EVALUATION OF THE EMISSION OF AIRBORNE HAZARDOUS SUBSTANCES - PART 1: SELECTION OF TEST METHODS |
| UNI EN 1870-15 : 2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 15: MULTI-BLADE CROSS-CUT SAWING MACHINES WITH INTEGRATED FEED OF THE WORKPIECE AND MANUAL LOADING AND/OR UNLOADING |
| UNI EN 12750 : 2013 | SAFETY OF WOODWORKING MACHINES - FOUR SIDED MOULDING MACHINES |
| UNI EN 848-3 : 2012 | SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES |
| UNI EN 1870-16 : 2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V CUTTING |
| UNI EN 860 : 2012 | SAFETY OF WOODWORKING MACHINES - ONE SIDE THICKNESS PLANNING MACHINES |
| UNI EN 859 : 2012 | SAFETY OF WOODWORKING MACHINES - HAND FED SURFACE PLANING MACHINES |
| UNI EN 848-1 : 2013 | SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 1: SINGLE SPINDLE VERTICAL MOULDING MACHINES |
| EN 1870-11:2013 | Safety of woodworking machines - Circular sawing machines - Part 11: Semi automatic horizontal cross-cut sawing machines with one saw unit (radial arm saws) |
| UNI EN 1870-9 : 2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 9: DOUBLE BLADE CIRCULAR SAWING MACHINES FOR CROSS-CUTTING WITH INTEGRATED FEED AND WITH MANUAL LOADING AND/OR UNLOADING |
| UNI EN 1870-12 : 2014 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 12: PENDULUM CROSS-CUT SAWING MACHINES |
| UNI EN 1870-14 : 2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 14: VERTICAL PANEL SAWING MACHINES |
| UNI EN 1870-10 : 2013 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES |
| UNI EN 1870-11 : 2013 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS) |
| EN 860:2007+A2:2012 | Safety of woodworking machines - One side thickness planing machines |
| UNI EN 1870-4 : 2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 4: MULTIBLADE RIP SAWING MACHINES WITH MANUAL LOADING AND/OR UNLOADING |
| UNI EN 848-2 : 2013 | SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 2: SINGLE SPINDLE HAND FED/INTEGRATED FED ROUTING MACHINES |
| UNI EN 861 : 2012 | SAFETY OF WOODWORKING MACHINES - SURFACE PLANING AND THICKNESSING MACHINES |
| UNI EN 1870-5 : 2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 5: CIRCULAR SAWBENCHES/UP-CUTTING CROSS-CUT SAWING MACHINES |
| UNI EN 1870-7:2012 | Safety of woodworking machines - Circular sawing machines - Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading |
| UNI EN 1807-1 : 2013 | SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - PART 1: TABLE BAND SAWS AND BAND RE-SAWS |
| 14/30293313 DC : 0 | BS EN ISO 19085-2 - WOODWORKING MACHINES - SAFETY - PART 2: HORIZONTAL BEAM PANEL CIRCULAR SAWING MACHINES |
| 10/30232425 DC : DRAFT DEC 2010 | BS EN 1870-15 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 15: MULTI-BLADE CROSS-CUT SAWING MACHINES WITH INTEGRATED FEED OF THE WORKPIECE AND MANUAL LOADING AND/OR UNLOADING |
| 10/30227080 DC : DRAFT JUNE 2010 | BS EN 691-1 - SAFETY OF WOODWORKING MACHINES - PART 1: COMMON REQUIREMENTS |
| DIN EN 1870-19:2014-03 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 19: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE) AND BUILDING SITE SAWS |
| I.S. EN 848-3:2012 | SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES |
| 11/30237560 DC : 0 | BS EN 1870-12 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 12: PENDULUM CROSS-CUT SAWING MACHINES |
| 16/30318928 DC : 0 | BS EN ISO 19085-7 - WOODWORKING MACHINES - SAFETY - PART 7: SURFACE PLANING THICKNESS PLANING COMBINED SURFACE/THICKNESS PLANING MACHINES |
| PREN 848-3 : DRAFT 2010 | SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOLS - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES |
| 12/30263881 DC : 0 | BS EN 1870-3 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 3: DOWN CUTTING CROSS-CUT SAWS AND DUAL PURPOSE DOWN CUTTING CROSS-CUT SAWS/CIRCULAR SAW BENCHES |
| 11/30231784 DC : 0 | BS EN 1870-13:2007+A1:2009/FPRA2 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 13: HORIZONTAL BEAM PANEL SAWING MACHINES |
| 16/30335973 DC : 0 | BS ISO 19085-9 - WOODWORKING MACHINES - SAFETY - PART 9: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE) |
| 14/30297793 DC : 0 | BS EN ISO 19085-3 - WOODWORKING MACHINES - SAFETY REQUIREMENTS - PART 3: NC BORING AND ROUTING MACHINES |
| DIN EN 1870-18:2013-08 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 18: DIMENSION SAWS |
| UNI EN 1870-18 : 2014 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 18: DIMENSION SAWS |
| UNE-EN 1807-2:2013 | Safety of woodworking machines - Band sawing machines - Part 2: Log sawing machines |
| I.S. EN 1870-18:2013 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 18: DIMENSION SAWS |
| DIN EN 940:2012-05 | SAFETY OF WOODWORKING MACHINES - COMBINED WOODWORKING MACHINES |
| DIN EN 861:2012-09 | SAFETY OF WOODWORKING MACHINES - SURFACE PLANING AND THICKNESSING MACHINES |
| DIN EN 859:2012-09 | SAFETY OF WOODWORKING MACHINES - HAND FED SURFACE PLANING MACHINES |
| DIN EN 1093-1:2009-02 | SAFETY OF MACHINERY - EVALUATION OF THE EMISSION OF AIRBORNE HAZARDOUS SUBSTANCES - PART 1: SELECTION OF TEST METHODS |
| BS EN 1093-1:2008 | Safety of machinery. Evaluation of the emission of airborne hazardous substances Selection of test methods |
| BS EN 1870-12:2013 | Safety of woodworking machines. Circular sawing machines Pendulum cross-cut sawing machines |
| BS EN 848-1 : 2007 | SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 1: SINGLE SPINDLE VERTICAL MOULDING MACHINES |
| UNE-EN 1870-15:2013 | Safety of woodworking machines - Circular sawing machines - Part 15: Multi-blade cross-cut sawing machines with integrated feed of the workpiece and manual loading and/or unloading |
| BS EN 1870-3:2014 | Safety of woodworking machines. Circular sawing machines Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches |
| UNE-EN 12750:2013 | Safety of woodworking machines - Four sided moulding machines |
| BS EN 12750:2013 | Safety of woodworking machines. Four sided moulding machines |
| BS EN 1870-11:2013 | Safety of woodworking machines. Circular sawing machines Semi automatic horizontal cross-cut sawing machines with one saw unit (radial arm saws) |
| BS EN 1870-4:2012 | Safety of woodworking machines. Circular sawing machines Multiblade rip sawing machines with manual loading and/or unloading |
| ISO 18217:2015 | Safety of woodworking machines Edge-banding machines fed by chain(s) |
| UNE-EN 860:2007 | Safety of woodworking machines - One side thickness planing machines |
| BS EN 1870-13 : 2007 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 13: HORIZONTAL BEAM PANEL SAWING MACHINES |
| UNE-EN 1870-9:2013 | Safety of woodworking machines - Circular sawing machines - Part 9: Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading |
| UNE-EN 1870-16:2013 | Safety of woodworking machines - Circular sawing machines - Part 16: Double mitre sawing machines for V cutting |
| UNE-EN 940:2010 | Safety of woodworking machines - Combined woodworking machines |
| UNE-EN 859:2008 | Safety of woodworking machines - Hand fed surface planing machines |
| BS EN 1870-5 : 2002 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 5: CIRCULAR SAW BENCHES/UP-CUTTING CROSS-CUT SAWING MACHINES |
| BS EN 860 : 2007 | SAFETY OF WOODWORKING MACHINES - ONE SIDE THICKNESS PLANING MACHINES |
| EN 691-1:2012 | Safety of woodworking machines - Part 1: Common requirements |
| EN 1870-16:2012 | Safety of woodworking machines - Circular sawing machines - Part 16: Double mitre sawing machines for V cutting |
| EN 1870-13:2007+A2:2012 | Safety of woodworking machines - Circular sawing machines - Part 13: Horizontal beam panel sawing machines |
| EN 1870-6:2017 | Safety of woodworking machines - Circular sawing machines - Part 6: Circular sawing machines for fire wood |
| EN 1870-3:2014 | Safety of woodworking machines - Circular sawing machines - Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches |
| EN 1870-18:2013 | Safety of woodworking machines - Circular sawing machines - Part 18: Dimension saws |
| EN 1870-14:2007+A2:2012 | Safety of woodworking machines - Circular sawing machines - Part 14: Vertical panel sawing machines |
| EN 1807-2:2013 | Safety of woodworking machines - Band sawing machines - Part 2: Log sawing machines |
| EN 1870-7:2012 | Safety of woodworking machines - Circular sawing machines - Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading |
| EN 1870-5 : 2002 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 5: CIRCULAR SAWBENCHES/UP-CUTTING CROSS-CUT SAWING MACHINES |
| EN 1870-19:2013 | Safety of woodworking machines - Circular sawing machines - Part 19: Circular saw benches (with and without sliding table) and building site saws |
| EN 1870-17:2012+A1:2015 | Safety of woodworking machines - Circular sawing machines - Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (radial arm saws) |
| EN 859:2007+A2:2012 | Safety of woodworking machines - Hand fed surface planing machines |
| EN 861:2007+A2:2012 | Safety of woodworking machines - Surface planing and thicknessing machines |
| EN 848-2 : 2007 COR 2012 | SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 2: SINGLE SPINDLE HAND FED/INTEGRATED FED ROUTING MACHINES |
| EN 940:2009+A1:2012 | Safety of woodworking machines - Combined woodworking machines |
| EN 1870-8:2012 | Safety of woodworking machines - Circular sawing machines - Part 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading |
| EN 1870-4:2012 | Safety of woodworking machines - Circular sawing machines - Part 4: Multiblade rip sawing machines with manual loading and/or unloading |
| EN 848-3:2012 | Safety of woodworking machines - One side moulding machines with rotating tool - Part 3: Numerically controlled (NC) boring and routing machines |
| EN 1870-12:2013 | Safety of woodworking machines - Circular sawing machines - Part 12: Pendulum cross-cut sawing machines |
| EN 1870-10:2013 | Safety of woodworking machines - Circular sawing machines - Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines |
| EN 1870-9:2012 | Safety of woodworking machines - Circular sawing machines - Part 9: Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading |
| ISO 19085-1:2017 | Woodworking machines Safety Part 1: Common requirements |
| BS EN 691-1:2012 | Safety of woodworking machines Common requirements |
| DIN EN 691-1:2013-01 | SAFETY OF WOODWORKING MACHINES - PART 1: COMMON REQUIREMENTS |
| 11/30232437 DC : 0 | BS EN 1870-6:2002+A1:2009/FPRA2 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 6: CIRCULAR SAWING MACHINES FOR FIREWOOD AND DUAL PURPOSE CIRCULAR SAWING MACHINES FOR FIREWOOD/CIRCULAR SAW BENCHES, WITH MANUAL LOADING AND/OR UNLOADING |
| 16/30318924 DC : 0 | BS EN ISO 19085-6 - WOODWORKING MACHINES - SAFETY - PART 6: SINGLE SPINDLE VERTICAL MOULDING MACHINES ('TOUPIES') |
| I.S. EN 1870-13:2007 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 13: HORIZONTAL BEAM PANEL SAWING MACHINES |
| 16/30341470 DC : 0 | BS EN ISO 19085-10 - WOODWORKING MACHINES - SAFETY - PART 10: BUILDING SITE SAWS (CONTRACTOR SAWS) |
| BS EN ISO 18217:2015 | Safety of woodworking machines. Edge-banding machines fed by chain(s) |
| 12/30260496 DC : 0 | BS EN 12750 - SAFETY OF WOODWORKING MACHINES - FOUR SIDED MOULDING MACHINES |
| 15/30300474 DC : DRAFT FEB 2015 | BS ISO 19085-5 - WOODWORKING MACHINES - SAFETY - PART 5: DIMENSION SAWS |
| 10/30232422 DC : DRAFT DEC 2010 | BS EN 1870-9 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 9: DOUBLE BLADE CIRCULAR SAWING MACHINES FOR CROSS-CUTTING WITH INTEGRATED FEED AND WITH MANUAL LOADING AND/OR UNLOADING |
| BS EN 1870-6:2017 | Safety of woodworking machines. Circular sawing machines Circular sawing machines for fire wood |
| UNE-EN 1870-18:2013 | Safety of woodworking machines - Circular sawing machines - Part 18: Dimension saws |
| 16/30331355 DC : 0 | BS EN ISO 19085-8 - WOODWORKING MACHINES - SAFETY - PART 8: WIDE BELT CALIBRATING AND SANDING MACHINES |
| UNE-EN ISO 18217:2016 | Safety of woodworking machines - Edge-banding machines fed by chain(s) (ISO 18217:2015) |
| I.S. EN 1807-1:2013 | SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - PART 1: TABLE BAND SAWS AND BAND RE-SAWS |
| I.S. EN ISO 19085-1:2017 | WOODWORKING MACHINES - SAFETY - PART 1: COMMON REQUIREMENTS (ISO 19085-1:2017) |
| I.S. EN 1870-19:2013 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 19: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE) AND BUILDING SITE SAWS |
| EN ISO 18217:2015 | Safety of woodworking machines - Edge-banding machines fed by chain(s) (ISO 18217:2015) |
| DIN EN 1870-4:2012-06 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 4: MULTIBLADE RIP SAWING MACHINES WITH MANUAL LOADING AND/OR UNLOADING |
| DIN EN 1870-5:2013-01 | Safety of woodworking machines - Circular sawing machines - Part 5: Circular saw benches/up-cutting cross-cut sawing machines (includes Amendment A2:2012) |
| BS EN 1870-8:2012 | Safety of woodworking machines. Circular sawing machines Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading |
| PD ISO/TR 18569:2004 | Safety of machinery. Guidelines for the understanding and use of safety of machinery standards. |
| BS EN 1870-16:2012 | Safety of woodworking machines. Circular sawing machines Double mitre sawing machines for V cutting |
| BS EN 848-3:2012 | Safety of woodworking machines. One side moulding machines with rotating tool Numerically controlled (NC) boring and routing machines |
| I.S. EN 859:2007 | SAFETY OF WOODWORKING MACHINES - HAND FED SURFACE PLANNING MACHINES |
| I.S. EN 860:2007 | SAFETY OF WOODWORKING MACHINES - ONE SIDE THICKNESS PLANING MACHINES |
| BS EN 1870-14 : 2007 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 14: VERTICAL PANEL SAWING MACHINES |
| BS EN 1870-17 : 2012 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 17: MANUAL HORIZONTAL CUTTING CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS) |
| BS EN 1870-10:2013 | Safety of woodworking machines. Circular sawing machines Single blade automatic and semi-automatic up-cutting cross-cut sawing machines |
| EN 12750:2013 | Safety of woodworking machines - Four sided moulding machines |
| UNE-EN 860:2007+A2:2012 | Safety of woodworking machines - One side thickness planing machines |
| UNE-EN 848-2:2007+A1:2010 | Safety of woodworking machines - One side moulding machines with rotating tool - Part 2: Single spindle hand fed/integrated fed routing machines |
| UNE-EN 848-2:2007 | Safety of woodworking machines - One side moulding machines with rotating tool - Part 2: Single spindle hand fed/integrated fed routing machines |
| UNE-EN 1870-17:2013 | Safety of woodworking machines - Circular sawing machines - Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (radial arm saws) |
| UNE-EN 1870-5:2003 | Safety of woodworking machines - Circular sawing machines - Part 5: Circular sawbenches/up-cutting cross-cut sawing machines. |
| UNE-EN 859:2008+A2:2012 | Safety of woodworking machines - Hand fed surface planing machines |
| ISO 7145:1982 | Determination of flowrate of fluids in closed conduits of circular cross-section Method of velocity measurement at one point of the cross-section |
| ISO 4053-1:1977 | Measurement of gas flow in conduits — Tracer methods — Part 1: General |
| ISO/TR 5168:1998 | Measurement of fluid flow Evaluation of uncertainties |
| ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements |
| 1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
| ISO 3966:2008 | Measurement of fluid flow in closed conduits Velocity area method using Pitot static tubes |
| EN 1070 : 1998 | SAFETY OF MACHINERY - TERMINOLOGY |
| ISO 4006:1991 | Measurement of fluid flow in closed conduits — Vocabulary and symbols |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.