• PREN 848-3 : DRAFT 2010

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOLS - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES

    Available format(s): 

    Superseded date:  01-10-2012

    Language(s): 

    Published date:  12-01-2013

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 List of significant hazards
    5 Safety requirements and/or measures
    6 Information for use
    Annex A (informative) - Electrical brake
    Annex B (normative) - Operating conditions for noise
                          measurement
    Annex C (normative) - Curtains on NC routing and NC
                          combined boring and routing
                          machines - Impact test method
    Annex D (informative) - Example of a test equipment
                            for impact test
    Annex E (normative) - Braking tests
    Annex F (normative) - Curtains on NC routing and NC
                          boring and routing machines
                          - Wear test method
    Annex G (normative) - Rigid guards on NC routing
                          machines - Impact test method
    Annex ZA (informative) - Relationship between this
                             European Standard and the
                             Essential Requirements of
                             EU Directive 2006/42/EC
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines all significant hazards, hazardous situations and events as listed in Clause 4, which are relevant to NC boring machines, NC routing machines and NC combined boring/routing machines herein after referred to as "machines" designed to cut solid wood, chip board, fibreboard, plywood and also these materials where these are covered with plastic/light alloy laminate or edgings when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee TC 142
    Document Type Draft
    Publisher Comite Europeen de Normalisation
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 1005-4:2005+A1:2008 Safety of machinery - Human physical performance - Part 4: Evaluation of working postures and movements in relation to machinery
    ISO 11202:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections
    EN ISO 11204:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections
    EN 894-3:2000+A1:2008 SAFETY OF MACHINERY - ERGONOMICS REQUIREMENTS FOR THE DESIGN OF DISPLAYS AND CONTROL ACTUATORS - PART 3: CONTROL ACTUATORS
    EN 848-2 : 2007 COR 2012 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 2: SINGLE SPINDLE HAND FED/INTEGRATED FED ROUTING MACHINES
    EN 982 : 96 + A1 2008 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR FLUID POWER SYSTEMS AND THEIR COMPONENTS - HYDRAULICS
    ISO 4871:1996 Acoustics Declaration and verification of noise emission values of machinery and equipment
    EN 1037:1995+A1:2008 SAFETY OF MACHINERY - PREVENTION OF UNEXPECTED START-UP
    ISO 3744:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane
    EN 61800-5-2:2017 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-2: SAFETY REQUIREMENTS - FUNCTIONAL (IEC 61800-5-2:2016)
    EN 60825-1:2014/AC:2017-06 SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014)
    EN 61508-1:2010 FUNCTIONAL SAFETY OF ELECTRICAL/ELECTRONIC/PROGRAMMABLE ELECTRONIC SAFETY-RELATED SYSTEMS - PART 1: GENERAL REQUIREMENTS
    EN 1088:1995+A2:2008 SAFETY OF MACHINERY - INTERLOCKING DEVICES ASSOCIATED WITH GUARDS - PRINCIPLES FOR DESIGN AND SELECTION
    CLC/TS 61496-2:2006 SAFETY OF MACHINERY - ELECTRO-SENSITIVE PROTECTIVE EQUIPMENT - PART 2: PARTICULAR REQUIREMENTS FOR EQUIPMENT USING ACTIVE OPTO-ELECTRONIC PROTECTIVE DEVICES (AOPDS)
    EN ISO 3743-2 : 2009 ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TESTS ROOMS
    ISO/TR 11688-1:1995 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
    EN 894-2:1997+A1:2008 SAFETY OF MACHINERY - ERGONOMICS REQUIREMENTS FOR THE DESIGN OF DISPLAYS AND CONTROL ACTUATORS - PART 2: DISPLAYS
    ISO 3743-2:1994 Acoustics Determination of sound power levels of noise sources using sound pressure Engineering methods for small, movable sources in reverberant fields Part 2: Methods for special reverberation test rooms
    IEC 60947-4-1:2009+AMD1:2012 CSV LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS
    EN 1093-9:1998+A1:2008 SAFETY OF MACHINERY - EVALUATION OF THE EMISSION OF AIRBORNE HAZARDOUS SUBSTANCES - PART 9: POLLUTANT CONCENTRATION PARAMETER, ROOM METHOD
    ISO 9614-1:1993 Acoustics Determination of sound power levels of noise sources using sound intensity Part 1: Measurement at discrete points
    EN 614-2:2000+A1:2008 SAFETY OF MACHINERY - ERGONOMIC DESIGN PRINCIPLES - PART 2: INTERACTIONS BETWEEN THE DESIGN OF MACHINERY AND WORK TASKS
    EN 50370-2 : 2003 ELECTROMAGNETIC COMPATIBILITY (EMC) - PRODUCT FAMILY STANDARD FOR MACHINE TOOLS - PART 2: IMMUNITY
    EN ISO 14121-1 : 2007 SAFETY OF MACHINERY - RISK ASSESSMENT - PART 1: PRINCIPLES
    EN 1837:1999+A1:2009 SAFETY OF MACHINERY - INTEGRAL LIGHTING OF MACHINES
    EN 349:1993+A1:2008 SAFETY OF MACHINERY - MINIMUM GAPS TO AVOID CRUSHING OF PARTS OF THE HUMAN BODY
    IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
    EN ISO 13850:2015 SAFETY OF MACHINERY - EMERGENCY STOP FUNCTION - PRINCIPLES FOR DESIGN (ISO 13850:2015)
    EN 1005-1:2001+A1:2008 Safety of machinery - Human physical performance - Part 1: Terms and definitions
    EN 1005-2:2003+A1:2008 SAFETY OF MACHINERY - HUMAN PHYSICAL PERFORMANCE - PART 2: MANUAL HANDLING OF MACHINERY AND COMPONENT PARTS OF MACHINERY
    IEC 60947-5-1 : 4.0 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES
    IEC 60825-1:2014 Safety of laser products - Part 1: Equipment classification and requirements
    EN 12779:2015 SAFETY OF WOODWORKING MACHINES - CHIP AND DUST EXTRACTION SYSTEMS WITH FIXED INSTALLATION - SAFETY RELATED PERFORMANCES AND SAFETY REQUIREMENTS
    ISO 7984:1988 Woodworking machines Technical classification of woodworking machines and auxiliary machines for woodworking
    EN 1760-1:1997+A1:2009 SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 1: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE MATS AND PRESSURE SENSITIVE FLOORS
    IEC 61508-4:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 4: Definitions and abbreviations (see Functional Safety and IEC 61508)
    EN ISO 3745:2012/A1:2017 ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - PRECISION METHODS FOR ANECHOIC ROOMS AND HEMI-ANECHOIC ROOMS (ISO 3745:2012/AMD 1:2017)
    EN 614-1:2006+A1:2009 SAFETY OF MACHINERY - ERGONOMIC DESIGN PRINCIPLES - PART 1: TERMINOLOGY AND GENERAL PRINCIPLES
    EN ISO 13857 : 2008 SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT HAZARD ZONES BEING REACHED BY UPPER AND LOWER LIMBS
    EN ISO 11688-2 : 2000 ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN
    ISO 14121-1:2007 Safety of machinery Risk assessment Part 1: Principles
    EN 50178 : 1997 ELECTRONIC EQUIPMENT FOR USE IN POWER INSTALLATIONS
    HD 22-1 : 200S4 CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING THERMOSETTING INSULATION - GENERAL REQUIREMENTS
    HD 21.1 : 200S4 CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING THERMOPLASTIC INSULATION - GENERAL REQUIREMENTS
    EN 61508-2:2010 FUNCTIONAL SAFETY OF ELECTRICAL/ELECTRONIC/PROGRAMMABLE ELECTRONIC SAFETY-RELATED SYSTEMS - PART 2: REQUIREMENTS FOR ELECTRICAL/ELECTRONIC/PROGRAMMABLE ELECTRONIC SAFETY-RELATED SYSTEMS
    ISO 3746:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane
    EN ISO 12100-1:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
    EN ISO 3746:2010 ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - SURVEY METHOD USING AN ENVELOPING MEASUREMENT SURFACE OVER A REFLECTING PLANE (ISO 3746:2010)
    EN 61496-1:2013/AC:2015 SAFETY OF MACHINERY - ELECTRO-SENSITIVE PROTECTIVE EQUIPMENT - PART 1: GENERAL REQUIREMENTS AND TESTS (IEC 61496-1:2012)
    EN 60947-4-1 : 2010 AMD 1 2012 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009/A1:2012)
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    EN ISO 3744:2010 ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR AN ESSENTIALLY FREE FIELD OVER A REFLECTING PLANE
    EN 847-2:2017 TOOLS FOR WOODWORKING - SAFETY REQUIREMENTS - PART 2: REQUIREMENTS FOR THE SHANK OF SHANK MOUNTED MILLING TOOLS/CIRCULAR SAW BLADES
    EN 62061:2005/A2:2015 SAFETY OF MACHINERY - FUNCTIONAL SAFETY OF SAFETY-RELATED ELECTRICAL, ELECTRONIC AND PROGRAMMABLE ELECTRONIC CONTROL SYSTEMS (IEC 62061:2005/A2:2015)
    IEC 60439-1:1999+AMD1:2004 CSV LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1: TYPE-TESTED AND PARTIALLY TYPE-TESTED ASSEMBLIES
    ISO 13849-2:2012 Safety of machinery Safety-related parts of control systems Part 2: Validation
    ISO 12100-2:2003 Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
    ISO 13857:2008 Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
    EN ISO 12100-2:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES
    IEC 61496-1:2012 Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests
    EN 60439-1:1999/A1:2004 LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1 - TYPE TESTED AND PARTIALLY TYPE TESTED ASSEMBLIES
    EN 847-1:2017 TOOLS FOR WOODWORKING - SAFETY REQUIREMENTS - PART 1: MILLING TOOLS, CIRCULAR SAW BLADES
    EN ISO 13849-2:2012 SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 2: VALIDATION (ISO 13849-2:2012)
    EN 983:1996+A1:2008 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR FLUID POWER SYSTEMS AND THEIR COMPONENTS - PNEUMATICS
    EN ISO 3743-1:2010 ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL MOVABLE SOURCES IN REVERBERANT FIELDS - PART 1: COMPARISON METHOD FOR A HARD-WALLED TEST ROOM
    ISO 12100-1:2003 Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
    EN ISO 13849-1:2015 SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN (ISO 13849-1:2015)
    ISO 13850:2015 Safety of machinery Emergency stop function Principles for design
    EN ISO 4871 : 2009 ACOUSTICS - DECLARATION AND VERIFICATION OF NOISE EMISSION VALUES OF MACHINERY AND EQUIPMENT (ISO 4871:1996)
    EN 1005-3:2002+A1:2008 Safety of machinery - Human physical performance - Part 3: Recommended force limits for machinery operation
    EN 1760-3:2004+A1:2009 SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 3: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE BUMPERS, PLATES, WIRES AND SIMILAR DEVICES
    IEC 61508-1:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements (see Functional Safety and IEC 61508)
    EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
    IEC 62061:2005+AMD1:2012+AMD2:2015 CSV Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems
    ISO 3745:2012 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Precision methods for anechoic rooms and hemi-anechoic rooms
    EN 50370-1 : 2005 Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 1: Emission
    EN ISO 11688-1 : 2009 ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 1: PLANNING (ISO/TR 11688-1:1995)
    ISO 13849-1:2015 Safety of machinery Safety-related parts of control systems Part 1: General principles for design
    ISO/TR 11688-2:1998 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design
    EN ISO 9614-1 : 2009 ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND INTENSITY - PART 1: MEASUREMENT AT DISCRETE POINTS
    EN ISO 11202:2010 ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING APPROXIMATE ENVIRONMENTAL CORRECTIONS
    IEC 61508-2:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 2: Requirements for electrical/electronic/programmable electronic safety-related systems (see Functional Safety and IEC 61508)
    ISO 11204:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections
    EN 1093-11:2001+A1:2008 SAFETY OF MACHINERY - EVALUATION OF THE EMISSION OF AIRBORNE HAZARDOUS SUBSTANCES - PART 11: DECONTAMINATION INDEX
    IEC 61800-5-2:2016 Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional
    IEC 61496-2:2013 Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs)
    ISO 3743-1:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room
    EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
    EN 61508-4:2010 FUNCTIONAL SAFETY OF ELECTRICAL/ELECTRONIC/PROGRAMMABLE ELECTRONIC SAFETY-RELATED SYSTEMS - PART 4: DEFINITIONS AND ABBREVIATIONS
    EN 894-1:1997+A1:2008 SAFETY OF MACHINERY - ERGONOMICS REQUIREMENTS FOR THE DESIGN OF DISPLAYS AND CONTROL ACTUATORS - PART 1: GENERAL PRINCIPLES FOR HUMAN INTERACTIONS WITH DISPLAYS AND CONTROL ACTUATORS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective