• EN 12206-1:2004

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    Paints and varnishes - Coating of aluminium and aluminium alloys for architectural purposes - Part 1: Coatings prepared from coating powder

    Available format(s): 

    Superseded date:  19-05-2021

    Language(s): 

    Published date:  07-07-2004

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Requirements
    5 Test methods
    Annex A (normative) Methods for the determination of the
            mass per unit area of conversion layers and for
            the identification of chromium, phosphorus and zinc
    Annex B (normative) Requirements for alternative pretreatment
    Annex C (normative) Measurement of film thickness
    Annex D (normative) Falling weight test apparatus
    Annex E (informative) Sequence of pretreatment stages
    Annex F (normative) Enhanced durability coating powders
    Bibliography

    Abstract - (Show below) - (Hide below)

    This Part of EN 12206 specifies requirements and the corresponding methods of test relating to the organic coating of aluminium and aluminium alloy extrusions, sheet and preformed sections for architectural purposes, using exclusively coating powders. It also describes :a) the pretreatment of the substrate prior to the coating process ;b) the coating powder ;c) the coating process ;d) the final product.Each item is dealt with separately in this Part of EN 12206 so that any interested party can ensure compliance appropriate to its area of responsibility.CAUTION : The procedures describes in this standard are intended to be carried out by suitably trained and/or supervised personnel. The substances and procedures used in this method may be injurious to health if adequate precautions are not taken. Attention is drawn in the text to specific hazards. This standard refers only to its technical suitability and does not absolve the user from statutory obligations relating to health and safety.

    General Product Information - (Show below) - (Hide below)

    Committee CEN/TC 139
    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    UNI EN 1090-3 : 2008 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES
    ONORM EN 1090-3 : 2008 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES
    DIN EN 1090-3:2008-09 EXECUTION OF STEEL AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL RULES FOR EXECUTION OF ALUMINIUM STRUCTURES
    BS IEC 60092-306:2009 Electrical installations in ships Equipment. Luminaires and lighting accessories
    PREN 1090-3 : DRAFT 2017 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES
    ISO/TS 16688:2017 Guidelines for the selection of coating types, tests and methods of assessing the performance of coated aluminium in architectural applications
    UNE-IEC 60092-306:2010 Electrical installations in ships - Part 306: Equipment - Luminaires and lighting accessories
    I.S. EN 12020-1:2008 ALUMINIUM AND ALUMINIUM ALLOYS - EXTRUDED PRECISION PROFILES IN ALLOYS EN AW-6060 AND EN AW-6063 - PART 1: TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY
    PD ISO/TS 16688:2017 Guidelines for the selection of coating types, tests and methods of assessing the performance of coated aluminium in architectural applications
    I.S. EN 1090-3:2008 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES
    PREN 16759 : DRAFT 2014 STRUCTURAL SEALANT GLAZING SYSTEMS (SSGS)
    EN 1090-3:2008 Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures
    ONORM EN 12020-1 : 2008 ALUMINIUM AND ALUMINIUM ALLOYS - EXTRUDED PRECISION PROFILES IN ALLOYS EN AW-6060 AND EN AW-6063 - PART 1: TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY
    08/30186163 DC : DRAFT JULY 2008 BS IEC 60092-306 - ELECTRICAL INSTALLATIONS IN SHIPS - PART 306: EQUIPMENT - LUMINAIRES AND LIGHTING ACCESSORIES
    17/30348949 DC : 0 BS EN 1090-3 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES
    BS EN 12020-1:2008 Aluminium and aluminium alloys. Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 Technical conditions for inspection and delivery
    UNI EN 12020-1 : 2008 ALUMINIUM AND ALUMINIUM ALLOYS - EXTRUDED PRECISION PROFILES IN ALLOYS EN AW-6060 AND EN AW-6063 - PART 1: TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY
    EN 12020-1:2008 Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1: Technical conditions for inspection and delivery
    BS EN 1090-3:2008 Execution of steel structures and aluminium structures Technical requirements for aluminium structures
    UNE-EN 1090-3:2011 Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures
    14/30300917 DC : 0 BS EN 16759 - STRUCTURAL SEALANT GLAZING SYSTEMS (SSGS)
    IEC 60092-306:2009 Electrical installations in ships - Part 306: Equipment - Luminaires and lighting accessories
    DIN EN 12020-1:2008-06 Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1: Technical conditions for inspection and delivery

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 971-1 : 1996 PAINTS AND VARNISHES - TERMS AND DEFINITIONS FOR COATING MATERIALS - PART 1: GENERAL TERMS
    EN ISO 3668:2001 Paints and varnishes - Visual comparison of the colour of paints (ISO 3668:1998)
    EN ISO 3231:1997 Paints and varnishes - Determination of resistance to humid atmospheres containing sulfur dioxide (ISO 3231:1993)
    EN ISO 2360:2017 Non-conductive coatings on non-magnetic electrically conductive base metals - Measurement of coating thickness - Amplitude-sensitive eddy-current method (ISO 2360:2017)
    ISO 6270-1:1998 Paints and varnishes Determination of resistance to humidity Part 1: Continuous condensation
    ISO 1520:2006 Paints and varnishes Cupping test
    EN ISO 2409:2013 Paints and varnishes - Cross-cut test (ISO 2409:2013)
    EN ISO 8130-9:1999 Coating powders - Part 9: Sampling (ISO 8130-9:1992)
    ISO 3668:2017 Paints and varnishes — Visual comparison of colour of paints
    ISO 2859-2:1985 Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection
    ISO 2810:2004 Paints and varnishes Natural weathering of coatings Exposure and assessment
    ISO 7724-3:1984 Paints and varnishes Colorimetry Part 3: Calculation of colour differences
    EN ISO 11341:2004 Paints and varnishes - Artificial weathering and exposure to artificial radiation - Exposure to filtered xenon-arc radiation (ISO 11341:2004)
    ISO 11341:2004 Paints and varnishes Artificial weathering and exposure to artificial radiation Exposure to filtered xenon-arc radiation
    EN ISO 1520:2006 Paints and varnishes - Cupping test (ISO 1520:2006)
    ISO 3696:1987 Water for analytical laboratory use — Specification and test methods
    ISO 9227:2017 Corrosion tests in artificial atmospheres — Salt spray tests
    EN ISO 3696:1995 Water for analytical laboratory use - Specification and test methods (ISO 3696:1987)
    ISO 8130-9:1992 Coating powders Part 9: Sampling
    ISO 1519:2011 Paints and varnishes Bend test (cylindrical mandrel)
    EN ISO 1519:2011 Paints and varnishes - Bend test (cylindrical mandrel) (ISO 1519:2011)
    ISO 2409:2013 Paints and varnishes Cross-cut test
    ISO 8565:2011 Metals and alloys Atmospheric corrosion testing General requirements
    EN ISO 8565:2011 Metals and alloys - Atmospheric corrosion testing - General requirements (ISO 8565:2011)
    EN 573-3:2013 Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products
    ISO 2813:2014 Paints and varnishes Determination of gloss value at 20, 60 and 85
    EN ISO 2813:2014 Paints and varnishes - Determination of gloss value at 20°, 60° and 85° (ISO 2813:2014)
    ISO 3231:1993 Paints and varnishes — Determination of resistance to humid atmospheres containing sulfur dioxide
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective