• There are no items in your cart

EN 13020:2015

Current

Current

The latest, up-to-date edition.

Road surface treatment machines - Safety requirements

Published date

18-11-2015

European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
6 Verification
7 Information for use
8 Marking
Annex A (informative) - Truck attachment plate
Annex B (informative) - Terminology
Annex C (informative) - Examples of technical measures
        to reduce noise
Annex D (normative) - Noise test code for the declaration
        of noise emission values (grade of accuracy)
Annex ZA (informative) - Relationship between this
         European Standard and the Essential
         Requirements of EU Directive 2006/42/EC
Bibliography

This European Standard applies to road surface treatment machines, which are in particular:-binder sprayers [or sprayers];-chipping spreaders [or spreaders];-machines for surface repairs (binder sprayer chipping spreader [or sprayer spreader]);-mastics asphalt mixers;-joint sealer;-micro-surfacing machines/slurry machines;-cold asphalt laying / micro-asphalt-paving machines(see also Clause 3).Road surface treatment machines can be mounted on a carrier vehicle, trailer or articulated truck, combining to form an integral unit. It is also possible to mount a road surface treatment machine on its own chassis construction and propulsion system (self-propelled or pedestrian-controlled). In all cases the machine and chassis form an integral unit.Directives and standards for the vehicular truck chassis aspects, termed 'carrier vehicle' in this document, would be those relative to that equipment, even where specific modifications have been made to realize the road surface treatment application. The use in public road traffic is governed by the national regulations.This European Standard deals with all significant hazards identified through a risk assessment relevant to road surface treatment machines when they are used as intended and under the conditions foreseen by the manufacturer (see Clause 4). This European Standard does not deal with significant hazards associated with pressurized tanks, and EMC. This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards associated with machine operation, setting and adjustments, load discharge and routine maintenance.This European Standard does not include requirements for the carrier vehicles or special constructions. These are covered in directives related to the construction of vehicles. Demountable bodywork systems (e.g. demountable containers) are specified in other standards. Vibrations are not dealt with in the standard, because for all machines of this family vibration is not a relevant hazard due to the low working speed and special working conditions (e.g. flat surface).This European Standard does not deal with the risks associated with the operation of the machines in potentially explosive atmospheres.This European Standard does not include requirements of the 94/55/EC Directive related to transport of dangerous goods by road but contains additional specifications in link with these existing requirements.This European Standard applies to machines which are manufactured after the date of approval of this standard by CEN.

DevelopmentNote
Supersedes PREN 13020. (11/2015)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current
Supersedes

Standards Relationship
NF EN 13020 : 2016 Identical
UNI EN 13020 : 2010 Identical
NS EN 13020 : 2015 Identical
SN EN 13020 : 2016 Identical
DIN EN 13020:2016-02 Identical
NBN EN 13020 : 2015 Identical
I.S. EN 13020:2015 Identical
NEN EN 13020 : 2015 Identical
UNE-EN 13020:2016 Identical
BS EN 13020:2015 Identical
PN EN 13020 : 2016 Identical
UNI EN 13020:2015 Identical

PD ISO/TR 12603:2010 Building construction machinery and equipment. Classification
DIN EN 500-1:2010-05 Mobile road construction machinery - Safety - Part 1: Common requirements (includes Amendment A1:2009)
17/30354108 DC : 0 BS EN 17106-1 - ROAD OPERATION MACHINERY - SAFETY - PART 1: GENERAL REQUIREMENTS
I.S. EN 500-1:2006 MOBILE ROAD CONSTRUCTION MACHINERY - SAFETY - PART 1: COMMON REQUIREMENTS
BS ISO 15644:2002 Road construction and maintenance equipment. Chippings spreaders. Terminology and commercial specifications
ISO/TR 12603:2010 Building construction machinery and equipment Classification
UNI EN 500-1 : 2010 MOBILE ROAD CONSTRUCTION MACHINERY - SAFETY - PART 1: COMMON REQUIREMENTS
BS ISO 22242 : 2005 ROAD CONSTRUCTION AND ROAD MAINTENANCE MACHINERY AND EQUIPMENT - BASIC TYPES - IDENTIFICATION AND DESCRIPTION
ISO 22242:2005 Road construction and road maintenance machinery and equipment — Basic types — Identification and description
ISO 15644:2002 Road construction and maintenance equipment Chippings spreaders Terminology and commercial specifications
BS EN 500-1 : 2006 MOBILE ROAD CONSTRUCTION MACHINERY - SAFETY - PART 1: COMMON REQUIREMENTS
EN 500-1:2006+A1:2009 Mobile road construction machinery - Safety - Part 1: Common requirements
UNE-EN 500-1:2007 Mobile road construction machinery - Safety - Part 1: Common requirements

ISO 12098:2004 Road vehicles Connectors for the electrical connection of towing and towed vehicles 15-pole connector for vehicles with 24 V nominal supply voltage
EN ISO 2860:2008 Earth-moving machinery - Minimum access dimensions (ISO 2860:1992)
EN 500-1:2006+A1:2009 Mobile road construction machinery - Safety - Part 1: Common requirements
EN ISO 15667 : 2000 ACOUSTICS - GUIDELINES FOR NOISE CONTROL BY ENCLOSURES AND CABINS
EN 894-3:2000+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators
ISO 4871:1996 Acoustics — Declaration and verification of noise emission values of machinery and equipment
ISO 14119:2013 Safety of machinery Interlocking devices associated with guards Principles for design and selection
ISO 730:2009 Agricultural wheeled tractors — Rear-mounted three-point linkage — Categories 1N, 1, 2N, 2, 3N, 3, 4N and 4
ISO 3744:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane
EN ISO 14163 : 1998 ACOUSTICS - GUIDELINES FOR NOISE CONTROL BY SILENCERS
ISO/TR 11688-1:1995 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
EN 894-2:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays
EN ISO 3457:2008 Earth-moving machinery - Guards - Definitions and requirements (ISO 3457:2003)
ISO 15667:2000 Acoustics Guidelines for noise control by enclosures and cabins
ISO 13732-1:2006 Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces
ISO 4413:2010 Hydraulic fluid power General rules and safety requirements for systems and their components
EN 349:1993+A1:2008 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
EN ISO 11820 : 1996 ACOUSTICS - MEASUREMENTS ON SILENCERS IN SITU
EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
EN ISO 11688-2 : 2000 ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN
ISO 12100:2010 Safety of machinery — General principles for design — Risk assessment and risk reduction
ISO 3795:1989 Road vehicles, and tractors and machinery for agriculture and forestry — Determination of burning behaviour of interior materials
EN ISO 13732-1:2008 Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006)
ISO 11820:1996 Acoustics — Measurements on silencers in situ
EN ISO 11201:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010)
ISO 2860:1992 Earth-moving machinery — Minimum access dimensions
EN ISO 3744:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)
ISO 3457:2003 Earth-moving machinery Guards Definitions and requirements
ISO 13857:2008 Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
EN ISO 14119:2013 Safety of machinery - Interlocking devices associated with guards - Principles for design and selection (ISO 14119:2013)
EN ISO 12100:2010 Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010)
ISO 14163:1998 Acoustics — Guidelines for noise control by silencers
ISO 1724:2003 Road vehicles Connectors for the electrical connection of towing and towed vehicles 7-pole connector type 12 N (normal) for vehicles with 12 V nominal supply voltage
EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
ISO 11546-1:1995 Acoustics Determination of sound insulation performances of enclosures Part 1: Measurements under laboratory conditions (for declaration purposes)
EN ISO 2867:2011 Earth-moving machinery - Access systems (ISO 2867:2011)
ISO 3731:2003 Road vehicles Connectors for the electrical connection of towing and towed vehicles 7-pole connector type 24 S (supplementary) for vehicles with 24 V nominal supply voltage
ISO 1185:2003 Road vehicles Connectors for the electrical connection of towing and towed vehicles 7-pole connector type 24 N (normal) for vehicles with 24 V nominal supply voltage
EN ISO 11546-1:2009 Acoustics - Determination of sound insulation performances of enclosures - Part 1: Measurements under laboratory conditions (for declaration purposes) (ISO 11546-1:1995)
EN ISO 4413:2010 Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010)
EN ISO 11688-1:2009 Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995)
ISO 2867:2011 Earth-moving machinery Access systems
ISO/TR 11688-2:1998 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design
EN 894-4:2010 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 4: Location and arrangement of displays and control actuators
ISO 11201:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections
ISO 6750:2005 Earth-moving machinery Operator's manual Content and format
ISO 8759-2:1998 Agricultural wheeled tractors — Front-mounted equipment — Part 2: Stationary equipment connection
EN 894-1:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.