EN 13155:2003+A2:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Cranes - Safety - Non-fixed load lifting attachments
08-01-2021
25-03-2009
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
6 Verification of the safety requirements and/or measures
7 Information for use
Annex A (normative) - General verification methods
Annex B (normative) - Verification methods for plate clamps
Annex C (normative) - Verification methods for vacuum lifters
Annex D (normative) - Verification methods for lifting magnets
Annex E (normative) - Verification methods for lifting beams
Annex F (normative) - Verification methods for lifting forks
Annex G (normative) - Verification methods for clamps
Annex H (informative) - Selection of a suitable set of
crane standards for a given application
Annex ZA (informative) - Relationship between this
European Standard and the Essential Requirements
of EU Directive 98/37/EC amended by Directive
98/79/EC
Annex ZB(informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
This European Standard specifies safety requirements for the following non-fixed load lifting attachments for cranes, hoists and manually controlled load manipulating devices: -plate clamps;-vacuum lifters;-self priming,-non-self priming (pump, venturi, turbine);-electric lifting magnets (battery fed and mains-fed);-permanent lifting magnets;-electro-permanent lifting magnets;-lifting beams;-C-hooks;-lifting forks;-clamps;defined in clause 3.This standard does not specify the additional requirements for:-non fixed load lifting attachments in direct contact with foodstuffs or pharmaceuticals requiring a high level of cleanliness for hygiene reasons;-hazards resulting from handling specific hazardous materials (e.g. explosives, hot molten masses, radiating materials);-hazards caused by operation in an explosive atmosphere;-hazards caused by noise;-electrical hazards;-hazards due to hydraulic and pneumatic components.This standard does not cover the hazards related to mechanical strength of structural elements of attachments designed for more than 20 000 lifting cycles.NOTEThe coefficient of utilization specified in clause 5.1.1 ensures that no fatigue verification is needed for less than 20 000 cycles. This is in accordance with the well accepted calculation codes e.g. FEM 1001.This standard does not cover attachments intended to lift above people.This standard does not cover slings, ladles, expanding mandrels, buckets, grabs, or grab buckets.The hazards covered by this European Standard are identified in clause 4.This European Standard does not cover hazards related to the lifting of persons.This European Standard is applicable to non-fixed load lifting attachments which are manufactured after the date of approval by CEN of this standard.
Committee |
CEN/TC 147
|
DevelopmentNote |
2003 Edition Re-Issued in March 2009 & incorporates AMD 2 2009. (04/2009)
|
DocumentType |
Standard
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
UNE-EN 13155:2004 | Identical |
BS EN 13155 : 2003 | Identical |
NEN EN 13155 : 2003 + A2 2009 | Identical |
NF EN 13155 : 2003 + A2 2009 | Identical |
I.S. EN 13155:2003 | Identical |
UNI EN 13155 : 2009 | Identical |
DIN EN 13155:2009-08 | Identical |
PN EN 13155 : 2006 + A2 2009 | Identical |
NS EN 13155 : 2003 + A2 2009 | Identical |
SN EN 13155 : 2003 + A2 2009 | Identical |
NBN EN 13155 : 2003 + A2 2009 | Identical |
ONORM EN 13155 : 2009 | Identical |
UNE-EN 13155:2004+A2:2009 | Identical |
UNE-EN 1501-5:2012 | Refuse collection vehicles - General requirements and safety requirements - Part 5: Lifting devices for refuse collection vehicles |
UNE-EN 16851:2017 | Cranes - Light crane systems |
DIN EN 16851 E : 2017 | CRANES - LIGHT CRANE SYSTEMS |
BS EN 13035-1:2008 | Machines and plants for the manufacture, treatment and processing of flat glass. Safety requirements Storage, handling and transportation equipment inside the factory |
12/30274592 DC : 0 | BS ISO 15818 - EARTH-MOVING MACHINERY - LIFTING AND TYING-DOWN ATTACHMENT POINTS - PERFORMANCE REQUIREMENTS |
I.S. EN 16851:2017 | CRANES - LIGHT CRANE SYSTEMS |
I.S. EN 1012-3:2013 | COMPRESSORS AND VACUUM PUMPS - SAFETY REQUIREMENTS - PART 3: PROCESS COMPRESSORS |
UNE-EN 14985:2012 | Cranes - Slewing jib cranes |
UNE-EN 16404:2016 | Railway applications - Re-railing and recovery requirements for railway vehicles |
ISO 15818:2017 | Earth-moving machinery Lifting and tying-down attachment points Performance requirements |
DIN EN 13135-1:2011-04 | CRANES - EQUIPMENT - PART 1: ELECTROTECHNICAL EQUIPMENT |
11/30235014 DC : 0 | BS EN 13135 - CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT |
BS EN 13001-1:2015 | Cranes. General design General principles and requirements |
I.S. EN 14985:2012 | CRANES - SLEWING JIB CRANES |
EN 1501-5:2011 | Refuse collection vehicles - General requirements and safety requirements - Part 5: Lifting devices for refuse collection vehicles |
EN 13035-2:2008 | Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 2: Storage, handling and transportation equipment outside the factory |
EN 13135-2:2004+A1:2010 | Cranes - Equipment - Part 2: Non-electrotechnical equipment |
VDI/BV-BS 6205 Blatt 2:2012-04 | Lifting inserts and lifting systems for precast concrete elements - Principles, design, applications - Production and placing on the market |
BS ISO 15818:2017 | Earth-moving machinery. Lifting and tying-down attachment points. Performance requirements |
BS EN 16404:2016 | Railway applications. Re-railing and recovery requirements for railway vehicles |
BS EN 13135 : 2013 | CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT |
EN 13135:2013+A1:2018 | Cranes - Safety - Design - Requirements for equipment |
I.S. EN 13135:2013 | CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT |
I.S. EN 13035-1:2008 | MACHINES AND PLANTS FOR THE MANUFACTURE, TREATMENT AND PROCESSING OF FLAT GLASS - SAFETY REQUIREMENTS - PART 1: STORAGE, HANDLING AND TRANSPORTATION EQUIPMENT INSIDE THE FACTORY |
DIN EN 14238:2010-02 | Cranes - Manually controlled load manipulating devices (includes Amendment A1:2009) |
DIN EN 15011:2014-09 | Cranes - Bridge and gantry cranes (includes Amendment A1:2014) |
BS EN 14238 : 2004 | CRANES - MANUALLY CONTROLLED LOAD MANIPULATING DEVICES |
UNE-EN 13135-2:2005 | Cranes - Equipment - Part 2: Non-electrotechnical equipment |
EN 16851:2017 | Cranes - Light crane systems |
I.S. EN 14238:2004 | CRANES - MANUALLY CONTROLLED LOAD MANIPULATING DEVICES |
DIN EN 13135-1:2004-05 | CRANES - EQUIPMENT - PART 1: ELECTROTECHNICAL EQUIPMENT |
I.S. EN 13001-1:2015 | CRANES - GENERAL DESIGN - PART 1: GENERAL PRINCIPLES AND REQUIREMENTS |
EN 15011:2011+A1:2014 | Cranes - Bridge and gantry cranes |
VDI 2381 Blatt 1:2009-07 | Final inspection of stationary and track-bound cranes - Instructionals form for experts |
07/30161753 DC : 0 | BS EN 15011 - CRANES - BRIDGE AND GANTRY CRANES |
15/30317558 DC : 0 | BS EN 16404 - RAILWAY APPLICATIONS - RE-RAILING AND RECOVERY REQUIREMENTS FOR RAILWAY VEHICLES |
BS EN 13035-2:2008 | Machines and plants for the manufacture, treatment and processing of flat glass. Safety requirements Storage, handling and transportation equipment outside the factory |
12/30235752 DC : 0 | BS EN 16404 - RAILWAY APPLICATIONS - RE-RAILING AND RECOVERY REQUIREMENTS FOR RAILWAY VEHICLES |
BS EN 1012-3:2013 | Compressors and vacuum pumps. Safety requirements Process compressors |
I.S. EN 16404:2016 | RAILWAY APPLICATIONS - RE-RAILING AND RECOVERY REQUIREMENTS FOR RAILWAY VEHICLES |
I.S. EN 1501-5:2011 | REFUSE COLLECTION VEHICLES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 5: LIFTING DEVICES FOR REFUSE COLLECTION VEHICLES |
UNE-EN 13135:2013 | Cranes - Safety - Design - Requirements for equipment |
DIN EN 13001-1:2015-06 | CRANES - GENERAL DESIGN - PART 1: GENERAL PRINCIPLES AND REQUIREMENTS |
BS EN 13135-2 : 2004 | CRANES - EQUIPMENT - PART 2: NON-ELECTROTECHNICAL EQUIPMENT |
UNE-EN 13001-1:2015 | Cranes - General design - Part 1: General principles and requirements |
UNI EN 13135-2 : 2010 | CRANES - EQUIPMENT - PART 2: NON-ELECTROTECHNICAL EQUIPMENT |
UNI EN 1012-3 : 2014 | COMPRESSORS AND VACUUM PUMPS - SAFETY REQUIREMENTS - PART 3: PROCESS COMPRESSORS |
UNI EN 14985 : 2012 | CRANES - SLEWING JIB CRANES |
UNI EN 14238 : 2009 | CRANES - MANUALLY CONTROLLED LOAD MANIPULATING DEVICES |
UNI EN 13135-1 : 2010 | CRANES - EQUIPMENT - PART 1: ELECTROTECHNICAL EQUIPMENT |
UNI EN 1501-5 : 2011 | REFUSE COLLECTION VEHICLES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 5: LIFTING DEVICES FOR REFUSE COLLECTION VEHICLES |
DIN EN 1501-5:2012-02 | Refuse collection vehicles - General requirements and safety requirements - Part 5: Lifting devices for refuse collection vehicles |
BS EN 1501-5:2011 | Refuse collection vehicles. General requirements and safety requirements Lifting devices for refuse collection vehicles |
DIN EN 13035-2:2008-10 | MACHINES AND PLANTS FOR THE MANUFACTURE, TREATMENT AND PROCESSING OF FLAT GLASS - SAFETY REQUIREMENTS - PART 2: STORAGE, HANDLING AND TRANSPORTATION EQUIPMENT OUTSIDE THE FACTORY |
BS EN 16851:2017 | Cranes. Light crane systems |
PREN 16404 : DRAFT 2015 | RAILWAY APPLICATIONS - RE-RAILING AND RECOVERY REQUIREMENTS FOR RAILWAY VEHICLES |
DIN EN 16851:2015-05 (Draft) | CRANES - LIGHT CRANE SYSTEMS |
DIN EN 13135:2013-05 | CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT |
I.S. EN 15011:2011 | CRANES - BRIDGE AND GANTRY CRANES |
DIN EN 14985:2012-05 | Cranes - Slewing jib cranes |
BS EN 13135-1 : 2003 | CRANES - EQUIPMENT - PART 1: ELECTROTECHNICAL EQUIPMENT |
BS EN 14985:2012 | Cranes. Slewing jib cranes |
BS EN 15011 : 2011 | CRANES - BRIDGE AND GANTRY CRANES |
10/30218104 DC : 0 | BS EN 15011 - CRANES - BRIDGE & GANTRY CRANES |
EN 14985:2012 | Cranes - Slewing jib cranes |
EN 14238:2004+A1:2009 | Cranes - Manually controlled load manipulating devices |
EN 16404:2016 | Railway applications - Re-railing and recovery requirements for railway vehicles |
DIN EN 16404:2016-05 | RAILWAY APPLICATIONS - RE-RAILING AND RECOVERY REQUIREMENTS FOR RAILWAY VEHICLES |
13/30273033 DC : 0 | BS EN 1012-3 - COMPRESSORS AND VACUUM PUMPS - SAFETY REQUIREMENTS - PART 3: PROCESS COMPRESSORS |
05/30112848 DC : 0 | EN 13035-2 - MACHINES AND PLANTS FOR THE MANUFACTURE, TREATMENT AND PROCESSING OF FLAT GLASS - SAFETY REQUIREMENTS - PART 2: STORAGE, HANDLING AND TRANSPORTATION EQUIPMENT OUTSIDE THE FACTORY |
I.S. EN 13035-2:2008 | MACHINES AND PLANTS FOR THE MANUFACTURE, TREATMENT AND PROCESSING OF FLAT GLASS - SAFETY REQUIREMENTS - PART 2: STORAGE, HANDLING AND TRANSPORTATION EQUIPMENT OUTSIDE THE FACTORY |
DIN EN 13135-2:2011-07 | CRANES - EQUIPMENT - PART 2: NON-ELECTROTECHNICAL EQUIPMENT |
17/30357380 DC : 0 | BS EN 15011 - CRANES - BRIDGE AND GANTRY CRANES |
EN 1012-3:2013 | Compressors and vacuum pumps - Safety requirements - Part 3: Process compressors |
EN 13135-1:2003+A1:2010 | Cranes - Equipment - Part 1: Electrotechnical equipment |
DIN EN 13035-1:2008-06 | Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 1: Storage, handling and transportation equipment inside the factory |
DIN EN 16851:2017-06 | Cranes - Light crane systems |
EN 13001-1:2015 | Cranes - General design - Part 1: General principles and requirements |
EN 13035-1:2008 | Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 1: Storage, handling and transportation equipment inside the factory |
UNI EN 15011 : 2014 | CRANES - BRIDGE AND GANTRY CRANES |
UNE-EN 15011:2011 | Cranes - Bridge and gantry cranes |
EN 818-5:1999+A1:2008 | Short link chain for lifting purposes - Safety - Part 5: Chain slings - Grade 4 |
EN 13557:2003+A2:2008 | Cranes - Controls and control stations |
EN 981:1996+A1:2008 | Safety of machinery - System of auditory and visual danger and information signals |
EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
EN 10025:1990/A1:1993 | HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS |
EN 1050 : 1996 | SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT |
EN 10045-1 : 1990 | METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD |
EN 818-4:1996+A1:2008 | Short link chain for lifting purposes - Safety - Part 4: Chain slings - Grade 8 |
EN 1492-2:2000+A1:2008 | Textile slings - Safety - Part 2: Roundslings made of man-made fibres for general purpose use |
EN 842:1996+A1:2008 | Safety of machinery - Visual danger signals - General requirements, design and testing |
ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
EN 1492-1:2000+A1:2008 | Textile slings - Safety - Part 1: Flat woven webbing slings made of man-made fibres for general purpose use |
1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
EN 457 : 1992 | SAFETY OF MACHINERY - AUDITORY DANGER SIGNALS - GENERAL REQUIREMENTS, DESIGN AND TESTING |
EN 1070 : 1998 | SAFETY OF MACHINERY - TERMINOLOGY |
EN 25817 : 1992 | ARC WELDED JOINTS IN STEEL - GUIDANCE ON QUALITY LEVELS FOR IMPERFECTIONS |
EN 13414-1:2003+A2:2008 | Steel wire rope slings - Safety - Part 1: Slings for general lifting service |
EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.