Skip to content
Please enter a keyword to search

  • 10/30218104 DC : 0

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    BS EN 15011 - CRANES - BRIDGE & GANTRY CRANES

    Available format(s):  Hardcopy, PDF

    Superseded date:  30-04-2011

    Language(s):  English

    Published date: 

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 List of significant hazards
    5 Safety requirements and/or protective measures
    6 Verification of safety requirements and/or
      protective measures
    7 Information for use
    Annex A (informative) - Guidance for specifying the
            operating duty according to EN 13001-1
    Annex B (informative) - Guidance for specifying the
            classes P of average number of accelerations
            according to EN 13001-1
    Annex C (informative) - Calculation of dynamic
            coefficient Phi[h](t)
    Annex D (normative) - Loads caused by skewing
    Annex E (informative) - Calculation of stall load
            factor for indirect acting lifting force
            limiter
    Annex F (informative) - Local stresses in wheel
             supporting flanges
    Annex G (normative) - Noise test code
    Annex H (informative) - Actions on crane supporting
            structures induced by cranes
    Annex I (informative) - Selection of a suitable set of
            crane standards for a given application
    Annex ZA (informative) - Relationship between this European
             standard and the Essential Requirements of EU
             Directive 2006/42/EC
    Bibliography

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee MHE/3/3
    Document Type Draft
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 11202:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections
    EN 81-43:2009 Safety rules for the construction and installation of lifts - Special lifts for the transport of persons and goods - Part 43: Lifts for cranes
    EN 1993-6:2007/AC:2009 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 6: CRANE SUPPORTING STRUCTURES
    EN ISO 11204:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010)
    EN 12385-4:2002+A1:2008 Steel wire ropes - Safety - Part 4: Stranded ropes for general lifting applications
    EN 13557:2003+A2:2008 Cranes - Controls and control stations
    ISO 4871:1996 Acoustics — Declaration and verification of noise emission values of machinery and equipment
    ISO 11660-5:2001 Cranes — Access, guards and restraints — Part 5: Bridge and gantry cranes
    EN 60947-5-5 : 1997 AMD 2 2016 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-5: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTRICAL EMERGENCY STOP DEVICE WITH MECHANICAL LATCHING FUNCTION (IEC 60947-5-5:1997/A2:2016)
    ISO 3744:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane
    ISO 15513:2000 Cranes — Competency requirements for crane drivers (operators), slingers, signallers and assessors
    EN 13155:2003+A2:2009 Cranes - Safety - Non-fixed load lifting attachments
    EN 60825-1:2014/AC:2017-06 SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014)
    ISO 12480-1:1997 Cranes Safe use Part 1: General
    ISO 9926-1:1990 Cranes Training of drivers Part 1: General
    EN 12644-2:2000+A1:2008 Cranes - Information for use and testing - Part 2: Marking
    ISO 9374-5:1991 Cranes Information to be provided Part 5: Overhead travelling cranes and portal bridge cranes
    ISO/TR 11688-1:1995 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
    EN 894-2:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays
    EN ISO 6892-1:2016 Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016)
    IEC 60364-4-41:2005+AMD1:2017 CSV Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock
    ISO 13732-1:2006 Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces
    EN 1991-3:2006/AC:2012 EUROCODE 1 - ACTIONS ON STRUCTURES - PART 3: ACTIONS INDUCED BY CRANES AND MACHINERY
    EN 349:1993+A1:2008 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
    EN 13135-2:2004+A1:2010 Cranes - Equipment - Part 2: Non-electrotechnical equipment
    ISO 12488-1:2012 Cranes — Tolerances for wheels and travel and traversing tracks — Part 1: General
    ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
    IEC 60204-11:2000 Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV
    IEC 60825-1:2014 Safety of laser products - Part 1: Equipment classification and requirements
    IEC 60204-32:2008 Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines
    ISO 16881-1:2005 Cranes Design calculation for rail wheels and associated trolley track supporting structure Part 1: General
    EN 13586:2004+A1:2008 Cranes - Access
    EN 614-1:2006+A1:2009 Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles
    EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
    EN ISO 11688-2 : 2000 ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN
    EN 12644-1:2001+A1:2008 Cranes - Information for use and testing - Part 1: Instructions
    ISO 9374-1:1989 Cranes Information to be provided Part 1: General
    EN ISO 13732-1:2008 Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006)
    EN 60204-32:2008 Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines
    EN ISO 11201:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010)
    EN 13001-2:2014 Crane safety - General design - Part 2: Load actions
    EN 13135-1:2003+A1:2010 Cranes - Equipment - Part 1: Electrotechnical equipment
    EN ISO 12100-1:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
    ISO 4309:2010 Cranes Wire ropes Care and maintenance, inspection and discard
    EN 13001-1:2015 Cranes - General design - Part 1: General principles and requirements
    EN ISO 3744:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)
    EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
    ISO 12100-2:2003 Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
    ISO 13857:2008 Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
    EN ISO 12100-2:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES
    ISO 6336-1:2006 Calculation of load capacity of spur and helical gears Part 1: Basic principles, introduction and general influence factors
    ISO 11203:1995 Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level
    EN 13157:2004+A1:2009 Cranes - Safety - Hand powered cranes
    EN 14492-2:2006+A1:2009/AC:2010 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
    ISO 2631-1:1997 Mechanical vibration and shock — Evaluation of human exposure to whole-body vibration — Part 1: General requirements
    EN 60204-11:2000/corrigendum:2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 11: REQUIREMENTS FOR HV EQUIPMENT FOR VOLTAGES ABOVE 1000 V A.C. OR 1500 V D.C. AND NOT EXCEEDING 36 KV
    ISO 12100-1:2003 Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
    EN ISO 13849-1:2015 Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
    EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
    ISO 4301-1:2016 Cranes — Classification — Part 1: General
    ISO 22986:2007 Cranes — Stiffness — Bridge and gantry cranes
    EN 795:2012 Personal fall protection equipment - Anchor devices
    ISO 8566-5:2017 Cranes — Cabins and control stations — Part 5: Overhead travelling and portal bridge cranes
    ISO 3864:1984 Safety colours and safety signs
    EN ISO 11688-1:2009 Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995)
    ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
    ISO/TR 11688-2:1998 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design
    ISO 12482-1:1995 Cranes Condition monitoring Part 1: General
    EN ISO 11202:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)
    EN ISO 11203:2009 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level (ISO 11203:1995)
    ISO 7752-5:1985 Lifting appliances Controls Layout and characteristics Part 5: Overhead travelling cranes and portal bridge cranes
    ISO 11201:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections
    ISO 11204:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections
    ISO 10245-5:1995 Cranes — Limiting and indicating devices — Part 5: Overhead travelling and portal bridge cranes
    CEN/TS 13001-3-2:2008 Cranes - General design - Part 3-2: Limit states and proof of competence of wire ropes in reeving systems
    IEC 60947-5-5:1997+AMD1:2005+AMD2:2016 CSV Low-voltage switchgear and controlgear - Part 5-5: Control circuitdevices and switching elements - Electrical emergency stop device with mechanical latching function
    EN 894-1:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective