Skip to content
Please enter a keyword to search

  • EN 14628:2005

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Ductile iron pipes, fittings and accessories - External polyethylene coating for pipes - Requirements and test methods

    Available format(s): 

    Superseded date:  12-03-2022

    Language(s): 

    Published date:  12-10-2005

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Ordering information
    5 Technical Requirements
    6 Performance requirements
    7 Test Methods
    Annex A (informative) Quality assurance
    Annex B (informative) Application process
    Annex C (informative) Coating material
    Bibliography

    Abstract - (Show below) - (Hide below)

    This European Standard defines the requirements and test methods applicable to factory applied extruded polyethylene coatings for the external corrosion protection of ductile iron pipes conforming to EN 545, EN 598 and EN 969 for use at operating temperatures up to 50 °C.This European Standard does not cover ductile iron pipes protected with thin PE sleeve. Special works at site like drilling, tapping etc. may influence the corrosion protection properties. Those job steps shall be included in the instructions of pipe saddle and accessory manufacturers and all other essential installation instructions. These instructions are not part of this European Standard.

    General Product Information - (Show below) - (Hide below)

    Committee CEN/TC 203
    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS ISO 13470:2012 Trenchless applications of ductile iron pipes systems. Product design and installation
    EN 545:2010 Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods
    ISO 13470:2012 Trenchless applications of ductile iron pipes systems — Product design and installation
    DIN EN 598:2009-10 Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods (includes Amendment A1:2009)
    BS EN 598 : 2007 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS
    UNE-EN 545:2011 Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods
    I.S. EN 598:2007 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS
    I.S. EN 545:2010 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR WATER PIPELINES - REQUIREMENTS AND TEST METHODS
    BS EN 545:2010 Ductile iron pipes, fittings, accessories and their joints for water pipelines. Requirements and test methods
    UNI EN 545 : 2010 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR WATER PIPELINES - REQUIREMENTS AND TEST METHODS
    UNI EN 598 : 2009 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS
    EN 598:2007+A1:2009 Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods
    DIN EN 545:2011-09 Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO/IEC Guide 62:1996 General requirements for bodies operating assessment and certification/registration of quality systems
    ISO 3219:1993 Plastics — Polymers/resins in the liquid state or as emulsions or dispersions — Determination of viscosity using a rotational viscometer with defined shear rate
    EN 598:2007+A1:2009 Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods
    EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
    ISO 3681:1996 Binders for paints and varnishes — Determination of saponification value — Titrimetric method
    EN ISO 527-1:2012 Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012)
    EN 969:2009 Ductile iron pipes, fittings, accessories and their joints for gas pipelines - Requirements and test methods
    ISO 6708:1995 Pipework components Definition and selection of DN (nominal size)
    ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
    EN ISO 6708:1995 Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995)
    EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
    EN 1238:2011 Adhesives - Determination of the softening point of thermoplastic adhesives (ring and ball)
    EN ISO 3219:1994 Plastics - Polymers/resins in the liquid state or as emulsions or dispersions - Determination of viscosity using a rotational viscometer with defined shear rate (ISO 3219:1993)
    ISO 9001:2015 Quality management systems — Requirements
    ISO 4892-2:2013 Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
    EN ISO 3681:1998 Binders for paints and varnishes - Determination of saponification value - Titrimetric method (ISO 3681:1996)
    EN ISO 1133:2005 PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS
    EN 545:2010 Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods
    EN 45012 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS
    EN ISO 4892-2:2013 Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013)
    ISO 1133:2005 Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective