![header thumbnail](/images/img-default-logo.png)
EN 62282-3-201:2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
![header thumbnail](/images/img-default-logo.png)
Fuel cell technologies - Part 3-201: Stationary fuel cell power systems - Performance test methods for small fuel cell power systems
31-03-2022
27-10-2017
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Configuration of small stationary fuel cell power system
6 Reference conditions
7 Heating value base
8 Test preparation
9 Test set-up
10 Instruments and measurement methods
11 Test conditions
12 Operating process
13 Test plan
14 Type tests on electric/thermal performance
15 Type tests on environmental performance
16 Test reports
Annex A (normative) - Heating values for components of
natural gases
Annex B (informative) - Examples of composition for natural
gases and propane gases
Annex C (informative) - Example of a test operation
schedule
Annex D (informative) - Typical exhaust gas components
Annex E (informative) - Guidelines for the contents of
detailed and full reports
Annex F (informative) - Selected duration of rated power
operation
Bibliography
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
IEC 62282-3-201:2017 provides test methods for the electrical, thermal and environmental performance of small stationary fuel cell power systems that meet the following criteria:- rated electric power output of less than 10 kW;- grid-connected/independent operation or stand-alone operation with single-phase AC output or 3-phase AC output not exceeding 1 000 V, or DC output not exceeding 1 500 V;- maximum allowable working pressure of less than 0,1 MPa (gauge) for the fuel and oxidant passages;- gaseous fuel (natural gas, liquefied petroleum gas, propane, butane, hydrogen, etc.) or liquid fuel (kerosene, methanol, etc.);- air as oxidant.This document describes type tests and their test methods only. This document covers fuel cell power systems whose primary purpose is the production of electric power.This new edition includes the following significant technical changes with respect to the previous edition: revision of test set-up, revision of measurement instruments, introduction of ramp-up test, introduction of rated operation cycle efficiency, introduction of electromagnetic compatibility (EMC) test, revision of exhaust gas test, introduction of typical durations of operation cycles.
Committee |
CLC/SR 105
|
DocumentType |
Standard
|
PublisherName |
European Committee for Standards - Electrical
|
Status |
Superseded
|
Standards | Relationship |
PN-EN 62282-3-201:2018-03 | Identical |
DIN EN 61851-21-1 : 2018 | Identical |
I.S. EN 62282-3-201:2013 | Identical |
CEI EN 62282-3-201 : 2ED 2018 | Identical |
PN EN 62282-3-201 : 2014 | Identical |
UNE-EN 62282-3-201:2017 | Identical |
NBN EN 62282-3-201 : 2013 | Identical |
VDE 0130-3-201 : 2014 | Identical |
UNE-EN 62282-3-201:2013 | Identical |
CEI EN 62282-3-201 : 2014 | Identical |
DIN EN 62282-3-201 : 2018-09 | Identical |
NEN EN IEC 62282-3-201 : 2017 | Identical |
VDE 0130-3-201:2018-09 | Identical |
BS EN 62282-3-201:2013 | Identical |
IEC 62282-3-201:2017 | Identical |
DIN EN 62282-3-201 : 2014 | Identical |
PNE-FprEN 62282-3-201:2016 | Identical |
BS EN 62282-3-201:2017 | Identical |
I.S. EN 62282-3-201:2017 | Identical |
NF EN 62282-3-201 : 2017 | Identical |
BS EN 62282-3-200:2016 | Fuel cell technologies Stationary fuel cell power systems. Performance test methods |
EN 62282-3-200:2016 | Fuel cell technologies - Part 3-200: Stationary fuel cell power systems - Performance test methods |
I.S. EN 62282-3-200:2016 | FUEL CELL TECHNOLOGIES - PART 3-200: STATIONARY FUEL CELL POWER SYSTEMS - PERFORMANCE TEST METHODS |
EN 62282-4-102:2017 | Fuel cell technologies - Part 4-102: Fuel cell power systems for industrial electric trucks - Performance test methods |
I.S. EN 62282-4-102:2017 | FUEL CELL TECHNOLOGIES - PART 4-102: FUEL CELL POWER SYSTEMS FOR INDUSTRIAL ELECTRIC TRUCKS - PERFORMANCE TEST METHODS |
BS EN 62282-4-102:2017 | Fuel cell technologies Fuel cell power systems for industrial electric trucks. Performance test methods |
CEI EN 62282-4-102 : 1ED 2017 | FUEL CELL TECHNOLOGIES - PART 4-102: FUEL CELL POWER SYSTEMS FOR INDUSTRIAL ELECTRIC TRUCKS - PERFORMANCE TEST METHODS |
ISO/TR 15916:2015 | Basic considerations for the safety of hydrogen systems |
IEC 61000-4-8 : 2.0 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-8: TESTING AND MEASUREMENT TECHNIQUES - POWER FREQUENCY MAGNETIC FIELD IMMUNITY TEST |
IEC 61672-2:2013+AMD1:2017 CSV | Electroacoustics - Sound level meters - Part 2: Pattern evaluation tests |
ISO 6976:2016 | Natural gas — Calculation of calorific values, density, relative density and Wobbe indices from composition |
IEC 61000-4-4 : 3.0EN+(REDLINE+VERSION) | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST |
EN 61000-4-11:2004/A1:2017 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-11: TESTING AND MEASUREMENT TECHNIQUES - VOLTAGE DIPS, SHORT INTERRUPTIONS AND VOLTAGE VARIATIONS IMMUNITY TESTS (IEC 61000-4-11:2004/A1:2017) |
IEC 61000-6-2:2016 | Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments |
IEC 60050-601:1985 | International Electrotechnical Vocabulary (IEV) - Part 601: Generation, transmission and distribution of electricity - General |
IEC TS 62282-1:2013 | Fuel cell technologies - Part 1: Terminology |
IEC 61000-4-11:2004+AMD1:2017 CSV | Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests |
IEC 61000-4-8:2009 | Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test |
IEC 61000-4-4:2012 RLV | Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test |
ISO 7941:1988 | Commercial propane and butane Analysis by gas chromatography |
ISO 7935:1992 | Stationary source emissions — Determination of the mass concentration of sulfur dioxide — Performance characteristics of automated measuring methods |
SAE ARP 1533 : 2016 | PROCEDURE FOR THE ANALYSIS AND EVALUATION OF GASEOUS EMISSIONS FROM AIRCRAFT ENGINES |
ISO 6060:1989 | Water quality — Determination of the chemical oxygen demand |
IEC 61000-4-6 : 4.0 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS |
IEC 61000-4-6:2013 | Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields |
IEC 62282-3-200:2015 | Fuel cell technologies - Part 3-200: Stationary fuel cell power systems - Performance test methods |
ISO 11042-1:1996 | Gas turbines — Exhaust gas emission — Part 1: Measurement and evaluation |
ISO 11042-2:1996 | Gas turbines — Exhaust gas emission — Part 2: Automated emission monitoring |
EN 61000-6-2:2005/corrigendum:2005 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS (IEC 61000-6-2:2005) |
EN 61000-4-8:2010 | Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test |
IEC 61000-4-2:2008 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV | Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test |
EN 61000-3-2:2014 | Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for harmonic current emissions (equipment input current ≤ 16 A per phase) |
ISO 11541:1997 | Natural gas Determination of water content at high pressure |
EN 62282-3-200:2016 | Fuel cell technologies - Part 3-200: Stationary fuel cell power systems - Performance test methods |
ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
EN 61000-4-4:2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST (IEC 61000-4-4:2012) |
ISO 5815-2:2003 | Water quality — Determination of biochemical oxygen demand after n days (BODn) — Part 2: Method for undiluted samples |
CISPR 11:2015 RLV | Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement |
ISO 10849:1996 | Stationary source emissions — Determination of the mass concentration of nitrogen oxides — Performance characteristics of automated measuring systems |
EN 61000-4-6:2014/AC:2015 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS (IEC 61000-4-6:2013) |
ISO 10523:2008 | Water quality — Determination of pH |
ISO 10396:2007 | Stationary source emissions — Sampling for the automated determination of gas emission concentrations for permanently-installed monitoring systems |
ISO 6798:1995 | Reciprocating internal combustion engines Measurement of emitted airborne noise Engineering method and survey method |
IEC 61000-6-2 : 3.0:2016 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY STANDARD FOR INDUSTRIAL ENVIRONMENTS |
IEC 61000-3-2 : 4.0 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-2: LIMITS - LIMITS FOR HARMONIC CURRENT EMISSIONS (EQUIPMENT INPUT CURRENT <= 16 A PER PHASE) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.