![header thumbnail](/images/img-default-logo.png)
EN ISO 11295:2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/img-default-logo.png)
Classification and information on design and applications of plastics piping systems used for renovation and replacement (ISO 11295:2017)
19-02-2022
06-12-2017
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Abbreviated terms
5 Classification of renovation and replacement techniques
6 Classification of renovation techniques
7 Classification of trenchless replacement techniques
8 Information on design
9 Aspects affecting installation
Bibliography
ISO 11295:2017 defines and describes families of techniques for the renovation and trenchless replacement (on or off the line of an existing pipeline) of non-pressure and pressure pipelines through the use of plastics pipes, including plastics composites formed in situ into pipes, fittings and ancillary components. It does not include new construction provided as network extension. For each technique family, it identifies areas of application including, but not limited to, underground drainage and sewerage, and underground water and gas supply networks.ISO 11295:2017 provides information on the principles of, but not the detailed methodologies for, the design of plastics piping systems used for renovation or trenchless replacement of existing pipelines, covering:- existing pipeline and site conditions;- functions of the new pipeline;- structural performance;- hydraulic performance;- installation aspects and site impact;- other factors affecting renovation or trenchless replacement technique selection.Necessary work on the existing pipeline prior to renovation and/or trenchless replacement is outside the scope of ISO 11295:2017.ISO 11295:2017 provides information needed to determine viable options and for identification of the optimal technique with regard to a given set of rehabilitation objectives.NOTE It is the responsibility of the designer to choose and design the renovation or trenchless replacement system.It does not specify the calculation methods to determine, for each viable technique, the required amount of lining or replacement pipe material needed to secure the desired performance of the rehabilitated pipeline.
Committee |
CEN/TC 155
|
DevelopmentNote |
Supersedes EN 13689. (03/2010)
|
DocumentType |
Standard
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
ONORM EN ISO 11295 : 2018 | Identical |
UNI EN ISO 11295 : 2010 | Identical |
I.S. EN ISO 11295:2010 | Identical |
SN EN ISO 11295 : 2010 | Identical |
ISO 11295:2017 | Identical |
NEN EN ISO 11295 : 2018 | Identical |
NS EN ISO 11295 : 2017 | Identical |
DIN EN ISO 11295:2016-08 (Draft) | Identical |
SN EN ISO 11295 : 2018 | Identical |
BS EN ISO 11295:2017 | Identical |
I.S. EN ISO 11295:2017 | Identical |
UNI EN ISO 11295:2018 | Identical |
PN EN ISO 11295 : 2018 | Identical |
SS-EN ISO 11295:2017 | Identical |
NF EN ISO 11295 : 2017 | Identical |
BS EN ISO 11295:2010 | Identical |
NBN EN ISO 11295 : 2010 | Identical |
UNE-EN ISO 11295:2011 | Identical |
UNE-EN ISO 11295:2018 | Identical |
ISO 25780:2011 | Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Pipes with flexible joints intended to be installed using jacking techniques |
EN 14636-1:2009 | Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints |
ISO 10467:2004 | Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin |
ISO 11296-1:2009 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General |
ISO 10639:2017 | Plastics piping systems for pressure and non-pressure water supply Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin |
ISO 11296-3:2009 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 3: Lining with close-fit pipes |
ISO 11299-1:2011 | Plastics piping systems for renovation of underground gas supply networks Part 1: General |
ISO 11296-7:2011 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 7: Lining with spirally-wound pipes |
ISO 24511:2007 | Activities relating to drinking water and wastewater services — Guidelines for the management of wastewater utilities and for the assessment of wastewater services |
EN 12889:2000 | Trenchless construction and testing of drains and sewers |
ISO 18672-1:2009 | Plastics piping systems for non-pressure drainage and sewerage — Polyester resin concrete (PRC) — Part 1: Pipes and fittings with flexible joints |
ISO 24512:2007 | Activities relating to drinking water and wastewater services — Guidelines for the management of drinking water utilities and for the assessment of drinking water services |
ISO 11299-3:2011 | Plastics piping systems for renovation of underground gas supply networks Part 3: Lining with close-fit pipes |
ISO 11298-3:2010 | Plastics piping systems for renovation of underground water supply networks Part 3: Lining with close-fit pipes |
ISO 11296-4:2009 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 4: Lining with cured-in-place pipes |
ISO 11298-1:2010 | Plastics piping systems for renovation of underground water supply networks Part 1: General |
ISO 16611:2017 | Plastics piping systems for drainage and sewerage without pressure — Non-circular pipes and joints made of glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resins (UP) — Dimensions, requirements and tests |
ISO 24510:2007 | Activities relating to drinking water and wastewater services — Guidelines for the assessment and for the improvement of the service to users |
ISO 11297-1:2013 | Plastics piping systems for renovation of underground drainage and sewerage networks under pressure Part 1: General |
ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
EN 16506:2014 | Systems for renovation of drains and sewers - Lining with a rigidly anchored plastics inner layer (RAPL) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.