Skip to content
Please enter a keyword to search

  • EN ISO 21003-3:2008

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Multilayer piping systems for hot and cold water installations inside buildings - Part 3: Fittings (ISO 21003-3:2008)

    Available format(s): 

    Superseded date:  06-11-2021

    Language(s): 

    Published date:  01-07-2008

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviated terms
    5 Material characteristics
       5.1 Plastics fitting materials specified in reference
            product standards
       5.2 Plastics fitting materials not specified in reference
            product standards
       5.3 Metallic fitting material
       5.4 Influence on water intended for human consumption
    6 General characteristics
       6.1 Appearance
       6.2 Opacity
    7 Geometrical characteristics
       7.1 General
       7.2 Dimensions of sockets for socket weld, electrofusion
            and solvent-cemented fittings
       7.3 Dimensions of metallic fittings
    8 Mechanical characteristics of plastics fittings (internal
       pressure test)
       8.1 General
       8.2 Plastics fitting materials specified in reference
            product standards
       8.3 Plastics fitting materials not specified in reference
            product standards
    9 Physical and chemical characteristics of plastics fittings
       9.1 Plastics fitting materials specified in reference
            product standards
       9.2 Plastics fitting materials not specified in reference
            product standards
       9.3 Sealing elements
    10 Performance requirements
    11 Marking
       11.1 General requirements
       11.2 Minimum required marking
    Annex A (normative) - List of reference product standards
    Bibliography

    Abstract - (Show below) - (Hide below)

    ISO 21003-3:2008 specifies the characteristics of fittings for multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water — whether or not the water is intended for human consumption (domestic systems) or for heating systems — under specified design pressures and temperatures appropriate to the class of applicationIt also specifies the test parameters for the test methods referred to in this part of ISO 21003.ISO 21003 is a reference product standard. It is applicable to multilayer pipes, fittings, their joints, and also to joints with components made of other plastics and non-plastics materials intended to be used for hot and cold water installations. ISO 21003-3 is intended for use only in conjunction with all the other parts of ISO 21003.

    General Product Information - (Show below) - (Hide below)

    Committee CEN/TC 155
    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    11/30197617 DC : 0 BS ISO 11855-5 - BUILDING ENVIRONMENT DESIGN - STANDARDS FOR THE DESIGN, CONSTRUCTION AND OPERATION OF RADIANT HEATING AND COOLING SYSTEMS - PART 5: INSTALLATION
    09/30202316 DC : 0 BS EN 12514-4 - PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 4: SAFETY REQUIREMENTS AND TESTS - PIPINGS AND PARTS WITHIN PIPELINES
    CEN ISO/TS 21003-7:2008/A1:2010 MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
    NF EN 1264-4 : 2010 WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION
    I.S. EN 1264-4:2009 WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION
    UNI EN 806-4 : 2010 SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4: INSTALLATION
    BS EN 806-4:2010 Specifications for installations inside buildings conveying water for human consumption Installation
    EN 1264-4:2009 Water based surface embedded heating and cooling systems - Part 4: Installation
    ISO/TS 21003-7:2008 Multilayer piping systems for hot and cold water installations inside buildings Part 7: Guidance for the assessment of conformity
    S.R. CEN ISO TS 21003-7:2008 MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
    NF EN 806-4 : 2010 SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4: INSTALLATION
    DIN EN 1264-4:2009-11 Water based surface embedded heating and cooling systems - Part 4: Installation
    BS EN 1264-4:2009 Water based surface embedded heating and cooling systems Installation
    DIN EN 806-4:2010-06 Specifications for installations inside buildings conveying water for human consumption - Part 4: Installation
    DD CEN ISO/TS 21003-7 : 2008 MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
    UNI EN 1264-4 : 2009 WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION
    I.S. EN 806-4:2010 SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4: INSTALLATION
    EN 806-4:2010 Specifications for installations inside buildings conveying water for human consumption - Part 4: Installation
    UNI CEN ISO/TS 21003-7 : 2010 MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
    UNE-EN 1264-4:2010 Water based surface embedded heating and cooling systems - Part 4: Installation

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 1254-3:1998 Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes
    EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
    ISO 15874-3:2013 Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 3: Fittings
    ISO 15877-3:2009 Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 3: Fittings
    ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
    BS 7291-2:2006 Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings Specification for polybutylene (PB) pipes and associated fittings
    ISO 1167-4:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
    ISO 9080:2012 Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
    EN 681-2:2000/A2:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 2: THERMOPLASTIC ELASTOMERS
    ISO 21003-5:2008 Multilayer piping systems for hot and cold water installations inside buildings — Part 5: Fitness for purpose of the system
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ISO 15876-3:2017 Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 3: Fittings
    ISO 1167-3:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components
    ISO 21003-2:2008 Multilayer piping systems for hot and cold water installations inside buildings — Part 2: Pipes
    ISO 21003-1:2008 Multilayer piping systems for hot and cold water installations inside buildings — Part 1: General
    ISO 22391-3:2009 Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 3: Fittings
    BS 7291-4:1990 Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings Specification for chlorinated polyvinyl chloride (PVC-C) pipes and associated fittings and solvent cement
    ISO/TS 21003-7:2008 Multilayer piping systems for hot and cold water installations inside buildings Part 7: Guidance for the assessment of conformity
    ISO 15875-3:2003 Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 3: Fittings
    EN 10226-1:2004 Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation
    ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
    ISO 7686:2005 Plastics pipes and fittings — Determination of opacity
    EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective