EN ISO 846:1997
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastics - Evaluation of the action of microorganisms (ISO 846:1997)
Superseded date
11-04-2019
Superseded by
Published date
15-06-1997
Publisher
Sorry this product is not available in your region.
Introduction
1 Scope
2 Normative references
3 Definitions
4 Principle
5 Apparatus and materials
6 Test specimens
7 Preparation of specimens
8 Procedures
9 Assessment
10 Expression of results
11 Accuracy of the measurements
12 Test report
13 Bibliography
Annexes
A Determination of the water content and water-holding
capacity of a soil
B Precision
C Information on test fungi
Defines methods for the determination of the deterioration of plastics caused by the action of fungi and bacteria and soil microorganisms. Not intended to determine the biodegradability of plastics. Determines deterioration by visual examination and/or changes in mass and/or changes in other physical properties. Applies to all plastic non-porous articles having an easy-to- clean surface.
| Committee |
CEN/TC 249
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| UNI EN ISO 846 : 1999 | Identical |
| SN EN ISO 846 : 1998 | Identical |
| NEN EN ISO 846 : 1997 | Identical |
| ISO 846:2019 | Identical |
| NEN EN ISO 846 : 2019 | Identical |
| DIN EN ISO 846:1997-10 | Identical |
| NS EN ISO 846 : 1ED 1997 | Identical |
| NF EN ISO 846 : 1997 | Identical |
| NBN EN ISO 846 : 1997 | Identical |
| I.S. EN ISO 846:2019 | Identical |
| PN EN ISO 846 : DEC 2002 | Identical |
| BS EN ISO 846:1997 | Identical |
| I.S. EN ISO 846:1998 | Identical |
| BS EN ISO 846:2019 | Identical |
| PN-EN ISO 846:2019 | Identical |
| SNV ISO 846 : 1978 | Identical |
| UNE-EN ISO 846:1998 | Identical |
| ONORM EN ISO 846 : 1997 | Identical |
| ISO 846:1997 | Identical |
| BS EN 60684-3-233:2006 | Flexible insulating sleeving Specifications for individual types of sleeving - Heat-shrinkable fluoroelastomer sleeving, flame retarded, fluid resistant, shrink ratio 2:1 |
| DIN EN 15619 E : 2014 | RUBBER OR PLASTIC COATED FABRICS - SAFETY OF TEMPORARY STRUCTURES (TENTS) - SPECIFICATION FOR COATED FABRICS INTENDED FOR TENTS AND RELATED STRUCTURES |
| 12/30256977 DC : 0 | BS EN 15619 - RUBBER OR PLASTIC COATED FABRICS - SAFETY OF TEMPORARY STRUCTURES (TENTS) - SPECIFICATION FOR COATED FABRICS INTENDED FOR TENTS AND RELATED STRUCTURES |
| UNI EN 15836-2 : 2010 | PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 2: REINFORCED MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 1,5 MM |
| BS EN 15651-3:2017 | Sealants for non-structural use in joints in buildings and pedestrian walkways Sealants for sanitary joints |
| CEI EN 60684-3-228 : 2005 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 228: HEAT-SHRINKABLE, SEMI-RIGID POLYVINYLIDENE FLUORIDE SLEEVING, FLAME RETARDED, FLUID RESISTANT, SHRINK RATIO 2:1 |
| BS EN 15619:2014 | Rubber or plastic coated fabrics. Safety of temporary structures (tents). Specification for coated fabrics intended for tents and related structures |
| I.S. EN 15836-2:2010 | PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 2: REINFORCED MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 1,5 MM |
| CEI EN 60684-3-247 : 2012 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 247: HEAT-SHRINKABLE POLYOLEFIN SLEEVING, DUAL WALL, NOT FLAME RETARDED, THICK AND MEDIUM WALL |
| BS EN 60684-3-212:2006 | Flexible insulating sleeving Specifications for individual types of sleeving - Heat-shrinkable polyolefin sleevings |
| BS EN 4708-104:2017 | Aerospace series. Sleeving, heat-shrinkable, for binding, insulation and identification Semi-rigid polyvinylidene fluoride (PDVF). Operating temperature - 55 °C to 175 °C. Product Standard |
| I.S. EN 62329-2:2006 | HEAT SHRINKABLE MOULDED SHAPES - PART 2: METHODS OF TEST |
| I.S. EN 60684-3-216:2005 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 216: HEAT-SHRINKABLE, FLAME-RETARDED, LIMITED-FIRE HAZARD SLEEVING |
| I.S. EN 15619:2014 | RUBBER OR PLASTIC COATED FABRICS - SAFETY OF TEMPORARY STRUCTURES (TENTS) - SPECIFICATION FOR COATED FABRICS INTENDED FOR TENTS AND RELATED STRUCTURES |
| I.S. EN 60684-3-212:2006 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 212: HEAT-SHRINKABLE POLYOLEFIN SLEEVINGS |
| BS EN 12613:2009 | Plastics warning devices for underground cables and pipelines with visual characteristics |
| UNE-EN 438-1:2016 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 1: Introduction and general information |
| BS EN 14879-5:2007 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media Linings on concrete components |
| EN 60684-3-228:2004 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 228: Heat-shrinkable, semi-rigid polyvinylidene fluoride sleeving, flame retarded, fluid resistant, shrink ratio 2:1 |
| EN 60684-3-271:2011 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 271: Heat-shrinkable elastomer sleevings, flame retarded, fluid resistant, shrink ratio 2:1 |
| VDI 6022 Blatt 1.2:2014-06 | Ventilation and indoor-air quality - Hygiene requirements for ventilation and air-conditioning systems and units - Requirements for underground components (VDI Ventilation Code of Practice) |
| BS EN 4708-001:2014 | Aerospace series. Sleeving, heat-shrinkable, for binding, insulation and identification Technical specification |
| UNE-EN 15836-1:2010 | Plastics - Plasticized poly(vinyl chloride) (PVC-P) membranes for inground swimming pools - Part 1: Homogenous membranes of nominal thickness equal to or greater than 0,75 mm |
| EN IEC 62677-2:2018 | Heat shrinkable low and medium voltage moulded shapes - Part 2 Methods of test |
| CEI EN 60684-3-212 : 2006 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 212: HEAT-SHRINKABLE POLYOLEFIN SLEEVINGS |
| 08/30181781 DC : DRAFT JULY 2008 | BS EN 15836-2 - PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 2: REINFORCED MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 1,5 MM |
| BS EN 60684-3-216 : 2005 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 216: HEAT-SHRINKABLE, FLAME-RETARDED, LIMITED-FIRE HAZARD SLEEVING |
| 08/30181778 DC : DRAFT JULY 2008 | BS EN 15836-1 - PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 1: HOMOGENOUS MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 0,75 MM |
| PREN 4708-102 : DRAFT 2017 | AEROSPACE SERIES - SLEEVING, HEAT-SHRINKABLE, FOR BINDING, INSULATION AND IDENTIFICATION - PART 102: VERY FLEXIBLE POLYMER - OPERATING TEMPERATURE -75 DEGREES C TO 150 DEGREES C - PRODUCT STANDARD |
| I.S. EN IEC 62677-2:2018 | HEAT SHRINKABLE LOW AND MEDIUM VOLTAGE MOULDED SHAPES - PART 2: METHODS OF TEST |
| DIN EN 14716:2005-03 | Stretched ceilings - Requirements and tests methods; German version EN 14716:2004 |
| BS EN 14716:2004 | Stretched ceilings. Requirements and test methods |
| I.S. EN 438-1:2016 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 1: INTRODUCTION AND GENERAL INFORMATION |
| I.S. EN 12613:2009 | PLASTICS WARNING DEVICES FOR UNDERGROUND CABLES AND PIPELINES WITH VISUAL CHARACTERISTICS |
| DIN 16726:2011-01 | PLASTIC SHEETING - TESTING |
| EN 12613:2009 | Plastics warning devices for underground cables and pipelines with visual characteristics |
| UNI EN 12613 : 2009 | PLASTICS WARNING DEVICES FOR UNDERGROUND CABLES AND PIPELINES WITH VISUAL CHARACTERISTICS |
| VDI 2055 Blatt 2:2013-10 | Thermal insulation of heated and refrigerated operational installations in the industry and in the building services - Technical basics for the verification of properties of insulating materials |
| VDI 2083 Blatt 18:2012-01 | Cleanroom technology - Biocontamination control |
| VDI 6032 Blatt 1:2015-05 | Ventilation and indoor-air quality in vehicles - Hygiene requirements for ventilation and air-conditioning systems |
| VDI 2047 Blatt 2:2015-01 | Open recooler systems - Securing hygienically sound operation of evaporative cooling systems (VDI Cooling Tower Code of Practice) |
| DIN EN 15836-2:2010-11 | Plastics - Plasticized poly(vinyl chloride) (PVC-P) membranes for inground swimming pools - Part 2: Reinforced membranes of nominal thickness equal to or greater than 1,5 mm |
| DIN EN 15836-1:2010-11 | Plastics - Plasticized poly(vinyl chloride) (PVC-P) membranes for inground swimming pools - Part 1: Homogenous membranes of nominal thickness equal to or greater than 0,75 mm |
| BS EN 60684-3-205:2011 | Flexible insulating sleeving Specifications for individual types of sleeving. Sheet 205: Heat-shrinkable chlorinated polyolefin sleeving, flame retarded, nominal shrink ratio 1,7:1 and 2:1 |
| DIN EN 15651-3:2016-10 (Draft) | SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 3: SEALANTS FOR SANITARY JOINTS |
| UNE-EN 15836-2:2010 | Plastics - Plasticized poly(vinyl chloride) (PVC-P) membranes for inground swimming pools - Part 2: Reinforced membranes of nominal thickness equal to or greater than 1,5 mm |
| CEI EN 60684-3-271 : 2012 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 271: HEAT-SHRINKABLE ELASTOMER SLEEVINGS, FLAME RETARDED, FLUID RESISTANT, SHRINK RATIO 2:1 |
| 14/30303782 DC : 0 | BS EN 438-1 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 1: INTRODUCTION AND GENERAL INFORMATION |
| PREN 438-1 : DRAFT 2014 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 1: INTRODUCTION AND GENERAL INFORMATION |
| BS EN 60684-3-400 to 402:2002 | Specification for flexible insulating sleeving. Specification requirements for individual types of sleeving Glass textile sleeving with silicone elastomer coating |
| BS EN 60684-3-280 : 2010 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 280: HEAT-SHRINKABLE, POLYOLEFIN SLEEVING, ANTI-TRACKING |
| CEI EN 60068-2-10 : 2006 | ENVIRONMENTAL TESTING - PART 2-10: TESTS - TEST J AND GUIDANCE: MOULD GROWTH |
| I.S. EN 60684-3-271:2011 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 271: HEAT-SHRINKABLE ELASTOMER SLEEVINGS, FLAME RETARDED, FLUID RESISTANT, SHRINK RATIO 2:1 |
| I.S. EN 15651-3:2017 | SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 3: SEALANTS FOR SANITARY JOINTS |
| I.S. EN 15836-1:2010 | PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 1: HOMOGENOUS MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 0,75 MM |
| UNI EN 4708-001 : 2014 | AEROSPACE SERIES - SLEEVING, HEAT-SHRINKABLE, FOR BINDING, INSULATION AND IDENTIFICATION - PART 001: TECHNICAL SPECIFICATION |
| NF EN 15836-2 : 2010 | PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 2: REINFORCED MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 1,5 MM |
| BS EN 60684-3-247 : 2011 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 247: HEAT-SHRINKABLE POLYOLEFIN SLEEVING, DUAL WALL, NOT FLAME RETARDED, THICK AND MEDIUM WALL (IEC 60684-3-247:2011) |
| IEC 60684-3-216:2001+AMD1:2005+AMD2:2013 CSV | Flexible insulating sleeving - Part 3: Specifications for individualtypes of sleeving - Sheet 216: Heat-shrinkable, flame- retarded, limited-fire-hazard sleeving |
| UNI EN 15619 : 2014 | RUBBER OR PLASTIC COATED FABRICS - SAFETY OF TEMPORARY STRUCTURES (TENTS) - SPECIFICATION FOR COATED FABRICS INTENDED FOR TENTS AND RELATED STRUCTURES |
| CEI EN 60684-3-205 : 2012 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 205: HEAT-SHRINKABLE CHLORINATED POLYOLEFIN SLEEVING, FLAME RETARDED, NOMINAL SHRINK RATIO 1,7:1 AND 2:1 |
| DIN EN 438-1:2016-06 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 1: INTRODUCTION AND GENERAL INFORMATION |
| UNI EN 15836-1 : 2010 | PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 1: HOMOGENOUS MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 0,75 MM |
| BS EN 15836-1:2010 | Plastics. Plasticized poly(vinyl chloride) (PVC-P) membranes for inground swimming pools Homogenous membranes of nominal thickness equal to or greater than 0,75 mm |
| BS EN IEC 62677-3-101:2018 | Heat-shrinkable low and medium voltage moulded shapes Specification for individual materials. Sheet 101: Heat-shrinkable, polyolefin moulded shapes for low voltage applications |
| CEI EN 60684-3-233 : 2006 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 233: HEAT-SHRINKABLE FLUOROELASTOMER SLEEVING, FLAME RETARDED, FLUID RESISTANT, SHRINK RATIO 2:1 |
| BS EN 62329-2:2006 | Heat shrinkable moulded shapes Methods of test |
| UNE-EN 15651-3:2017 | Sealants for non-structural use in joints in buildings and pedestrian walkways - Part 3: Sealants for sanitary joints |
| 07/30158827 DC : 0 | BS EN 15619 - RUBBER OR PLASTIC COATED FABRICS - SAFETY OF TEMPORARY STRUCTURES (TENTS) - SPECIFICATION FOR COATED FABRICS INTENDED FOR TENTS AND RELATED STRUCTURES |
| PREN 4708-001 : DRAFT 2017 | AEROSPACE SERIES - SLEEVING, HEAT-SHRINKABLE, FOR BINDING, INSULATION AND IDENTIFICATION - PART 001: TECHNICAL SPECIFICATION |
| BS EN 60684-3-283 : 2011 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 283: HEAT-SHRINKABLE, POLYOLEFIN SLEEVING, FOR BUS-BAR INSULATION |
| EN 4708-104:2017 | Aerospace series - Sleeving, heat-shrinkable, for binding, insulation and identification - Part 104: Semi-rigid polyvinylidene fluoride (PDVF) - Operating temperature - 55 °C to 175 °C - Product Standard |
| I.S. EN 60684-3-283:2011 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 283: HEAT-SHRINKABLE, POLYOLEFIN SLEEVING, FOR BUS-BAR INSULATION |
| I.S. EN 4708-104:2017 | AEROSPACE SERIES - SLEEVING, HEAT-SHRINKABLE, FOR BINDING, INSULATION AND IDENTIFICATION - PART 104: SEMI-RIGID POLYVINYLIDENE FLUORIDE (PDVF) - OPERATING TEMPERATURE -55 DEGREES C TO 175 DEGREES C - PRODUCT STANDARD |
| I.S. EN 60684-3-247:2011 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 247: HEAT-SHRINKABLE POLYOLEFIN SLEEVING, DUAL WALL, NOT FLAME RETARDED, THICK AND MEDIUM WALL |
| 14/30311128 DC : 0 | BS EN 14716 - STRETCHED CEILINGS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 60684-3-340 TO 342:2003 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEETS 340 TO 342: EXPANDABLE BRAIDED POLYETHYLENE TEREPHTHALATE TEXTILE SLEEVING |
| I.S. EN 60684-3-228:2004 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 228: HEAT-SHRINKABLE, SEMI-RIGID POLYVINYLIDENE FLUORIDE SLEEVING, FLAME RETARDED, FLUID RESISTANT, SHRINK RATIO 2:1 |
| EN 60684-3-212:2006/corrigendum:2006 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 212: Heat-shrinkable polyolefin sleevings |
| DIN EN 12613:2009-09 | Plastics warning devices for underground cables and pipelines with visual characteristics; German version EN 12613:2009 |
| UNE-EN 12613:2010 | Plastics warning devices for underground cables and pipelines with visual characteristics |
| EN 14879-5:2007 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 5: Linings on concrete components |
| EN 438-1:2016 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 1: Introduction and general information |
| EN 15619:2014 | Rubber or plastic coated fabrics - Safety of temporary structures (tents) - Specification for coated fabrics intended for tents and related structures |
| EN 14716:2004 | Stretched ceilings - Requirements and test methods |
| EN 15651-3:2017 | Sealants for non-structural use in joints in buildings and pedestrian walkways - Part 3: Sealants for sanitary joints |
| EN 15836-2:2010 | Plastics - Plasticized poly(vinyl chloride) (PVC-P) membranes for inground swimming pools - Part 2: Reinforced membranes of nominal thickness equal to or greater than 1,5 mm |
| EN 4708-001:2014 | Aerospace series - Sleeving, heat-shrinkable, for binding, insulation and identification - Part 001: Technical specification |
| EN 15836-1:2010 | Plastics - Plasticized poly(vinyl chloride) (PVC-P) membranes for inground swimming pools - Part 1: Homogenous membranes of nominal thickness equal to or greater than 0,75 mm |
| 16/30344964 DC : 0 | BS EN 4708-001 - AEROSPACE SERIES - SLEEVING, HEAT-SHRINKABLE, FOR BINDING, INSULATION AND IDENTIFICATION - PART 001: TECHNICAL SPECIFICATION |
| PREN 14716 : DRAFT 2014 | STRETCHED CEILINGS - REQUIREMENTS AND TEST METHODS |
| OVE/ONORM EN 60068-2-10 : 2006 | ENVIRONMENTAL TESTING - PART 2-10: TESTS - TEST J AND GUIDANCE: MOULD GROWTH |
| BS EN 60684-3-228:2004 | Flexible insulating sleeving Specification requirements for individual types of sleeving - Heat-shrinkable, semi-rigid polyvinylidene fluoride sleeving, flame retarded, fluid resistant, shrink ratio 2:1 |
| DIN EN 15619:2014-07 | RUBBER OR PLASTIC COATED FABRICS - SAFETY OF TEMPORARY STRUCTURES (TENTS) - SPECIFICATION FOR COATED FABRICS INTENDED FOR TENTS AND RELATED STRUCTURES |
| BS EN 15836-2:2010 | Plastics. Plasticized poly(vinyl chloride) (PVC-P) membranes for inground swimming pools Reinforced membranes of nominal thickness equal to or greater than 1,5 mm |
| BS EN 60684-3-343 to 345:2002 | Specification for flexible insulating sleeving. Specification requirements for individual types of sleeving Expandable braided ethylene chlorotrifluoroethylene (E-CTFE) textile sleeving, uncoated |
| BS EN 60684-3-271:2004 | Flexible insulating sleeving Specifications for individual types of sleeving - Heat-shrinkable elastomer sleeving, flame retarded, fluid resistant, shrink ratio 2:1 |
| 12/30254138 DC : 0 | BS EN 15651-3 - SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 3: SEALANTS FOR SANITARY JOINTS |
| EN IEC 62677-3-101:2018 | Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 101: Heat-shrinkable, polyolefin moulded shapes for low voltage applications |
| 07/30164611 DC : 0 | BS EN 15651-2 - SEALANTS FOR JOINTS IN BUILDING CONSTRUCTION - DEFINITIONS, REQUIREMENTS AND EVALUATION OF CONFORMITY - PART 2: SEALANTS FOR GLAZING |
| BS EN 60684-3-340 to 342:2003 | Specification for flexible insulating sleeving. Specification requirements for individual types of sleeving Expandable braided polyethylene terephthalate textile sleeving |
| I.S. EN 60684-3-205:2011 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 205: HEAT-SHRINKABLE CHLORINATED POLYOLEFIN SLEEVING, FLAME RETARDED, NOMINAL SHRINK RATIO 1,7:1 AND 2:1 |
| 03/310127 DC : DRAFT JUNE 2003 | EN 14716 - STRETCHED CEILINGS - REQUIREMENTS AND TEST METHODS |
| 07/30163692 DC : 0 | BS EN 15651-3 - SEALANTS FOR JOINTS IN BUILDING CONSTRUCTION - DEFINITIONS, REQUIREMENTS AND EVALUATION OF CONFORMITY - PART 3: SEALANTS FOR SANITARY JOINTS |
| I.S. EN IEC 62677-3-101:2018 | HEAT-SHRINKABLE LOW AND MEDIUM VOLTAGE MOULDED SHAPES - PART 3: SPECIFICATION FOR INDIVIDUAL MATERIALS - SHEET 101: HEAT-SHRINKABLE, POLYOLEFIN MOULDED SHAPES FOR LOW VOLTAGE APPLICATIONS |
| I.S. EN 60684-3-400 TO 402:2002 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEETS 400 TO 402: GLASS TEXTILE SLEEVING WITH SILICONE ELASTOMER COATING |
| NF EN 15836-1 : 2010 | PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MEMBRANES FOR INGROUND SWIMMING POOLS - PART 1: HOMOGENOUS MEMBRANES OF NOMINAL THICKNESS EQUAL TO OR GREATER THAN 0,75 MM |
| I.S. EN 4708-001:2014 | AEROSPACE SERIES - SLEEVING, HEAT-SHRINKABLE, FOR BINDING, INSULATION AND IDENTIFICATION - PART 001: TECHNICAL SPECIFICATION |
| I.S. EN 60684-3-280:2010 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 280: HEAT-SHRINKABLE, POLYOLEFIN SLEEVING, ANTI-TRACKING |
| I.S. EN 60684-3-343 TO 345:2002 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEETS 343 TO 345: EXPANDABLE BRAIDED ETHYLENE CHLOROTRIFLUOROETHYLENE (E-CTFE) TEXTILE SLEEVING, UNCOATED |
| PREN 15651-3 : DRAFT 2012 | SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 3: SEALANTS FOR SANITARY JOINTS |
| I.S. EN 60684-3-233:2006 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 233: HEAT-SHRINKABLE FLUOROELASTOMER SLEEVING, FLAME RETARDED, FLUID RESISTANT, SHRINK RATIO 2:1 |
| EN 60684-3-280:2010/A1:2014 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 280: HEAT-SHRINKABLE, POLYOLEFIN SLEEVING, ANTI-TRACKING (IEC 60684-3-280:2010/A1:2013) |
| EN 60684-3-247:2011/A1:2017 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 247: HEAT-SHRINKABLE POLYOLEFIN SLEEVING, DUAL WALL, NOT FLAME RETARDED, THICK AND MEDIUM WALL (IEC 60684-3-247:2011/A1:2016) |
| EN 60684-3-340 to 342:2003 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheets 340 to 342: Expandable braided polyethylene terephthalate textile sleeving |
| EN 60684-3-216:2005/A2:2014 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 216: HEAT-SHRINKABLE, FLAME-RETARDED, LIMITED-FIRE HAZARD SLEEVING (IEC 60684-3-216:2001 + CORRIGENDUM 2003 + A1:2005) |
| BS EN 438-1:2016 | High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates) Introduction and general information |
| DIN EN 15651-3:2017-07 | SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 3: SEALANTS FOR SANITARY JOINTS |
| EN 60684-3-400 to 402:2002 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheets 400 to 402: Glass textile sleeving with silicone elastomer coating |
| EN 62329-2:2006 | Heat shrinkable moulded shapes - Part 2: Methods of test |
| EN 60684-3-233:2006/corrigendum:2006 | FLEXIBLE INSULATING SLEEVING - PART 3: SPECIFICATIONS FOR INDIVIDUAL TYPES OF SLEEVING - SHEET 233: HEAT-SHRINKABLE FLUOROELASTOMER SLEEVING, FLAME RETARDED, FLUID RESISTANT, SHRINK RATIO 2:1 |
| DIN EN 14879-5:2007-10 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 5: Linings on concrete components |
| EN 60684-3-343 to 345:2002 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheets 343 to 345: Expandable braided ethylene chlorotrifluoroethylene (E-CTFE) textile sleeving, uncoated |
| EN 60684-3-205:2011 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 205: Heat-shrinkable chlorinated polyolefin sleeving, flame retarded, nominal shrink ratio 1,7:1 and 2:1 |
| IEC 60068-2-10:2005 | Environmental testing - Part 2-10: Tests - Test J and guidance: Mould growth |
| ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.