Skip to content
Please enter a keyword to search

  • EN ISO 9093-2:2002

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Small craft - Seacocks and through-hull fittings - Part 2: Non-metallic (ISO 9093-2:2002)

    Available format(s): 

    Superseded date:  18-04-2019

    Language(s): 

    Published date:  15-10-2002

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Material requirements
    5 Thread
    6 Through-hull fittings - Requirements
    7 Seacocks - Requirements
    8 Hose fittings - Requirements
    9 Drain plugs - Requirements
    10 Installation
    11 Manufacturers installation information
    12 Owner's manual
    13 Service manual
    Annex A (normative) Strength test
    Bibliography
    Annex ZA (normative) Normative references to international
                           publications with their relevant
                           European publications
    Annex ZB (informative) Clauses of this European Standard
                           addressing essential requirements or
                           other provisions of EU Directives

    Abstract - (Show below) - (Hide below)

    ISO 9093-2:2002 specifies requirements for the manufacture and installation of non-metallic through-hull fittings and/or assemblies comprising through-hull fittings, seacocks, hose fittings and/or drain plugs and components attached thereto, used in small craft of up to 24 m length of hull. ISO 9093-2:2002 is not applicable to engine exhaust fittings and sail drive through-hull connections.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    ISO 15083:2003 Small craft - Bilge-pumping systems
    I.S. EN ISO 15083:2003 SMALL CRAFT - BILGE-PUMPING SYSTEMS
    EN ISO 15083:2003 Small craft - Bilge-pumping systems (ISO 15083:2003)
    BS EN ISO 15083:2003 Small craft. Bilge-pumping systems
    DIN EN ISO 15083:2003-06 SMALL CRAFT - BILGE PUMPING SYSTEMS

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 75-1:2013 Plastics Determination of temperature of deflection under load Part 1: General test method
    EN ISO 180:2000/A2:2013 PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000/AMD 2:2013)
    ISO 527-4:1997 Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
    EN ISO 527-4:1997 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 4: TEST CONDITIONS FOR ISOTROPIC AND ORTHOTROPIC FIBRE-REINFORCED PLASTIC COMPOSITES
    EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
    1994/25/EC : 1994 DIRECTIVE 94/25/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 16 JUNE 1994 ON THE APPROXIMATION OF THE LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO RECREATIONAL CRAFT
    EN ISO 178:2010/A1:2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
    ISO 8666:2016 Small craft Principal data
    EN ISO 527-1:2012 Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012)
    ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
    ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
    ISO 527-5:2009 Plastics Determination of tensile properties Part 5: Test conditions for unidirectional fibre-reinforced plastic composites
    ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
    ISO 180:2000 Plastics Determination of Izod impact strength
    EN ISO 527-5:2009 Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:2009)
    ISO 75-3:2004 Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
    ISO 527-3:1995 Plastics Determination of tensile properties Part 3: Test conditions for films and sheets
    ISO 178:2010 Plastics Determination of flexural properties
    EN ISO 527-3:1995/AC:2002 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 3: TEST CONDITIONS FOR FILMS AND SHEETS
    ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective