Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN ISO 9093-2:2002

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    SMALL CRAFT - SEACOCKS AND THROUGH-HULL FITTINGS - PART 2: NON-METALLIC

    Available format(s):  Hardcopy, PDF

    Superseded date:  23-07-2013

    Language(s):  English

    Published date:  01-01-2002

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Material requirements
    5 Thread
    6 Through-hull fittings - Requirements
    7 Seacocks - Requirements
    8 Hose fittings - Requirements
    9 Drain plugs - Requirements
    10 Installation
    11 Manufacturers installation information
    12 Owner's manual
    13 Service manual
    Annex A (normative) Strength test
    Bibliography
    Annex ZA (normative) Normative references to
             international publications with their
             relevant European publications
    Annex ZB (informative) Clauses of this European
             Standard addressing essential requirements
             or other provisions of EU Directives

    Abstract - (Show below) - (Hide below)

    Defines requirements for the manufacture and installation of non-metallic through-hull fittings and/or assemblies comprising through-hull fittings, seacocks, hose fittings and/or drain plugs and components attached thereto, used in small craft of up to 24 m length of hull.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 75-1:2013 Plastics Determination of temperature of deflection under load Part 1: General test method
    EN ISO 180:2000/A2:2013 PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000/AMD 2:2013)
    ISO 527-4:1997 Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
    EN ISO 527-4:1997 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 4: TEST CONDITIONS FOR ISOTROPIC AND ORTHOTROPIC FIBRE-REINFORCED PLASTIC COMPOSITES
    EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
    EN ISO 178:2010/A1:2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
    EN ISO 527-1:2012 Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012)
    ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
    ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
    ISO 527-5:2009 Plastics Determination of tensile properties Part 5: Test conditions for unidirectional fibre-reinforced plastic composites
    ISO 180:2000 Plastics Determination of Izod impact strength
    EN ISO 527-5:2009 Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:2009)
    ISO 75-3:2004 Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
    ISO 527-3:1995 Plastics Determination of tensile properties Part 3: Test conditions for films and sheets
    ISO 178:2010 Plastics Determination of flexural properties
    EN ISO 527-3:1995/AC:2002 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 3: TEST CONDITIONS FOR FILMS AND SHEETS
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective