I.S. EN 12068:1999
Current
The latest, up-to-date edition.
CATHODIC PROTECTION - EXTERNAL ORGANIC COATINGS FOR THE CORROSION PROTECTION OF BURIED OR IMMERSED STEEL PIPELINES USED IN CONJUNCTION WITH CATHODIC PROTECTION - TAPES AND SHRINKABLE MATERIALS
Hardcopy , PDF
English
01-01-1999
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative References
3 Definitions
4 Classification and designation
5 Requirements
6 Quality
Annex A (normative) Tape strength, elongation at break,
modulus at 10% elongation, bursting strength
Annex B (normative) Peel strength layer to layer
Annex C (normative) Peel strength to pipe surface and
factory coating
Annex D (normative) Lap shear strength
Annex E (normative) Thermal ageing resistance
Annex F (normative) Ultraviolet irradiation resistance
Annex G (normative) Indentation resistance
Annex H (normative) Impact resistance
Annex J (normative) Specific electrical insulation
resistance
Annex K (normative) Cathodic disbondment resistance
Annex L (informative) Saponification value
Annex M (normative) Microbiological resistance
Annex N (normative) Low temperature flexibility
Annex P (normative) Low temperature unrolling test
Annex Q (normative) Drip resistance of petrolatum tapes
Defines the functional requirements and test procedures for external organic coatings based on tapes or shrinkable materials to be used for corrosion protection of buried and immersed steel pipelines in conjunction with cathodic protection.
| DocumentType |
Standard
|
| Pages |
50
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| NBN EN 12068 : 1998 | Identical |
| NF EN 12068 : 1999 | Identical |
| EN 12068:1998 | Identical |
| SN EN 12068 : 1999 | Identical |
| UNE-EN 12068:1999 | Identical |
| BS EN 12068:1999 | Identical |
| ONORM EN 12068 : 2000 | Identical |
| NS EN 12068 : 1ED 1999 | Identical |
| UNI EN 12068 : 2002 | Identical |
| NEN EN 12068 : 1998 | Identical |
| DIN EN 12068:1999-03 | Identical |
| I.S. 329:2015 | GAS DISTRIBUTION MAINS (EDITION 3) |
| ISO 4892-1:2016 | Plastics — Methods of exposure to laboratory light sources — Part 1: General guidance |
| ISO 8501-1:2007 | Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings |
| ISO 8503-2:2012 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel — Comparator procedure |
| ISO 2808:2007 | Paints and varnishes Determination of film thickness |
| EN ISO 9002:1994/AC:1997 | QUALITY SYSTEMS - SPECIFICATION FOR PRODUCTION AND INSTALLATION |
| ISO 3303:1990 | Rubber- or plastics-coated fabrics — Determination of bursting strength |
| ISO 4591:1992 | Plastics — Film and sheeting — Determination of average thickness of a sample, and average thickness and yield of a roll, by gravimetric techniques (gravimetric thickness) |
| EN ISO 9003:1994/AC:1997 | QUALITY SYSTEMS - SPECIFICATION FOR FINAL INSPECTION AND TEST |
| ISO 2811:1974 | Paints and varnishes — Determination of density |
| ISO 1523:2002 | Determination of flash point — Closed cup equilibrium method |
| EN ISO 9000-1 : 1994 | QUALITY MANAGEMENT AND QUALITY ASSURANCE STANDARDS - PART 1: GUIDELINES FOR SELECTION AND USE (ISO 9000-1:1994) |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 3801:1977 | Textiles — Woven fabrics — Determination of mass per unit length and mass per unit area |
| EN ISO 8503-2:2012 | Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel - Comparator procedure (ISO 8503-2:2012) |
| ISO 5893:2002 | Rubber and plastics test equipment Tensile, flexural and compression types (constant rate of traverse) Specification |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| ISO 3251:2008 | Paints, varnishes and plastics Determination of non-volatile-matter content |
| PREN 1427 : DRAFT 2013 | BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF THE SOFTENING POINT - RING AND BALL METHOD |
| ISO 7254:1984 | Paints and varnishes — Assessment of natural spreading rate — Brush application |
| ISO 4593:1993 | Plastics Film and sheeting Determination of thickness by mechanical scanning |
| ISO 4626:1980 | Volatile organic liquids Determination of boiling range of organic solvents used as raw materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.