I.S. EN 13121-1:2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 1: RAW MATERIALS - SPECIFICATION CONDITIONS AND ACCEPTANCE CONDITIONS
Hardcopy , PDF
12-10-2021
English
01-01-2003
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
3.1 Terms and definitions
3.2 Symbols and abbreviations
4 Thermosetting resins
4.1 General
4.2 Unsaturated polyester resins
4.3 Vinylester resins
4.4 Vinylester urethane resins
4.5 Epoxy resins
4.6 Furane resins
4.7 Phenolic resins
4.8 Characterisation of thermosetting resins in the
uncured state
4.9 Characterisation of thermosetting resins in the
cured state
5 Curing agents for unsaturated polyester and vinylester
resins
5.1 General
5.2 Initiators
5.3 Accelerators, organometallic
5.4 Promoters
5.5 Inhibitors
6 Reinforcing materials
6.1 General
6.2 Surface nonwovens
6.3 Chopped strand mats
6.4 Continuous strand mats
6.5 Woven fabrics/Woven roving fabrics
6.6 Roving for winding and for chopping applications
7 Additives
7.1 General
7.2 Thixotropic agents
7.3 Conductive fillers
7.4 Fire retardants
7.5 Paraffin wax
7.6 Aggregates and fillers
7.7 Ultra violet absorbers
7.8 Pigments
7.9 Surface active agents
8 Thermoplastic lining materials
8.1 General
8.2 Mechanical and thermal properties
8.3 Welding consumables
8.4 Dimensional stability
9 Material conformance documentation
9.1 General
9.2 Unsaturated polyester, vinylester and vinylester
urethane resins
9.3 Epoxy resins and hardeners
9.4 Furane and phenolic resins
9.5 Curing agents and additives
9.6 Surface nonwovens
9.7 Chopped strand mats
9.8 Woven fabrics/Woven roving fabrics
9.9 Roving for winding and for chopping applications
9.10 Thermoplastic lining
Annex ZA (informative) Relationship between this European
standard and the Essential requirements of EU
Directives 97/23/EC
Bibliography
Describes requirements for specification and acceptance conditions of raw materials for GRP tanks and vessels with or without lining for storage or processing of fluids, factory made or site built, non pressurised or pressurised, for use above ground.
| DocumentType |
Standard
|
| Pages |
23
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NF EN 13121-1 : 2003 | Identical |
| NEN EN 13121-1 : 2003 | Identical |
| EN 13121-1:2003 | Identical |
| BS EN 13121-1:2003 | Identical |
| UNE-EN 13121-1:2004 | Identical |
| DIN EN 13121-1:2003-10 | Identical |
| SN EN 13121-1 : 2003 | Identical |
| NBN EN 13121-1 : 2003 | Identical |
| NS EN 13121-1 : 1ED 2003 | Identical |
| UNI EN 13121-1 : 2004 | Identical |
| ONORM EN 13121-1 : 2003 | Identical |
| EN ISO 9771:1997 | Plastics - Phenolic resins - Determination of the pseudo-adiabatic temperature rise of liquid resols when cured under acid conditions (ISO 9771:1995) |
| EN ISO 3001:1999 | Plastics - Epoxy compounds - Determination of epoxy equivalent (ISO 3001:1999) |
| EN ISO 9073-2:1996 | Textiles - Test methods for nonwovens - Part 2: Determination of thickness (EN ISO 9073-2:1995) |
| PREN 13121-3 : DRAFT 2014 | GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 3: DESIGN AND WORKMANSHIP |
| EN ISO 6721-2:2008 | Plastics - Determination of dynamic mechanical properties - Part 2: Torsion-pendulum method (ISO 6721-2:2008) |
| ISO 2797:1986 | Textile glass — Rovings — Basis for a specification |
| ISO 5661:1983 | Petroleum products Hydrocarbon liquids Determination of refractive index |
| EN 59:2016 | Glass reinforced plastics - Determination of indentation hardness by means of a Barcol hardness tester |
| EN ISO 527-2:2012 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| ISO 6271:2015 | Clear liquids Estimation of colour by the platinum-cobalt colour scale |
| ISO 3374:2000 | Reinforcement products Mats and fabrics Determination of mass per unit area |
| EN ISO 1675:1998 | Plastics - Liquid resins - Determination of density by the pyknometer method (ISO 1675:1985) |
| ISO 11359-2:1999 | Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
| EN ISO 1163-1:1999 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1163-1:1995) |
| EN ISO 3251:2008 | Paints, varnishes and plastics - Determination of non-volatile-matter content (ISO 3251:2008) |
| EN ISO 1889:2009 | Reinforcement yarns - Determination of linear density (ISO 1889:2009) |
| PREN 13121-4 : DRAFT 1998 | GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 4: DELIVERY, INSTALLATION AND MAINTENANCE |
| EN ISO 75-2:2013 | Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013) |
| ISO 1183:1987 | Plastics Methods for determining the density and relative density of non-cellular plastics |
| EN 29092:1992 | Textiles - Nonwovens - Definition |
| EN ISO 3219:1994 | Plastics - Polymers/resins in the liquid state or as emulsions or dispersions - Determination of viscosity using a rotational viscometer with defined shear rate (ISO 3219:1993) |
| ISO 2113:1996 | Reinforcement fibres — Woven fabrics — Basis for a specification |
| ISO 1887:2014 | Textile glass Determination of combustible-matter content |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 2559:2011 | Textile glass Mats (made from chopped or continuous strands) Designation and basis for specifications |
| EN ISO 2554 : 1999 | PLASTICS - UNSATURATED POLYESTER RESINS - DETERMINATION OF HYSROXYL VALUE |
| EN ISO 9702:1998 | Plastics - Amine epoxide hardeners - Determination of primary, secondary and tertiary amine group nitrogen content (ISO 9702:1996) |
| EN ISO 2592:2017 | Petroleum and related products - Determination of flash and fire points - Cleveland open cup method (ISO 2592:2017) |
| ISO 2211:1973 | Liquid chemical products Measurement of colour in Hazen units (platinum-cobalt scale) |
| EN ISO 868:2003 | Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868:2003) |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| EN ISO 306:2013 | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2013) |
| EN ISO 472:2013 | Plastics - Vocabulary (ISO 472:2013) |
| EN ISO 2535:2002 | Plastics - Unsaturated polyester resins - Measurement of gel time at ambient temperature (ISO 2535:2001) |
| EN ISO 3344:1997 | Reinforcement products - Determination of moisture content (ISO 3344:1997) |
| 1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.