I.S. EN 13341:2005
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
STATIC THERMOPLASTIC TANKS FOR ABOVE GROUND STORAGE OF DOMESTIC HEATING OILS, KEROSENE AND DIESEL FUELS - BLOW MOULDED AND ROTATIONALLY MOULDED POLYETHYLENE TANKS AND ROTATIONALLY MOULDED TANKS MADE OF ANIONICALLY POLYMERIZED POLYAMIDE 6 - REQUIREMENTS AND TEST METHODS
Hardcopy , PDF
19-01-2011
English
03-06-2005
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Evaluation of conformity
6 Requirements for tanks
7 Durability
8 Marking, transport, handling and installation
of tanks
Annex A (normative) - Test methods for determination
of material characteristics
Annex B (normative) - Test methods for determination
of tank characteristics
Annex ZA (informative) - Clauses of this European Standard
addressing essential requirements or other
provisions of EU Directives
Bibliography
Describes requirements for materials, physical properties and performance of single blow moulded and rotationally moulded polyethylene tanks and of rotationally moulded tanks made of anionically polymerized polyamide 6, with or without reinforcements, for above ground storage of domestic heating oil, kerosene and diesel fuels for the supply of building heating/cooling systems.
| DevelopmentNote |
2005 Edition Re-Issued in January 2011 & incorporates AMD 1 2011. (07/2011)
|
| DocumentType |
Standard
|
| Pages |
41
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Withdrawn
|
| Standards | Relationship |
| UNE-EN 13341:2005 | Identical |
| UNI EN 13341 : 2011 | Identical |
| NBN EN 13341 : 2005 + A1 2011 | Identical |
| NF EN 13341 : 2005 + A1 2011 | Identical |
| BS EN 13341 : 2005 | Identical |
| NS EN 13341 : 2005 + A1 2011 | Identical |
| DIN EN 13341:2011-04 | Identical |
| SN EN 13341 : 2005 + A1 2011 | Identical |
| NEN EN 13341 : 2005 + A1 2011 | Identical |
| EN 13341:2005+A1:2011 | Identical |
| EN 13160-7:2016 | Leak detection systems - Part 7: Requirements and test/assessment methods for interstitial spaces, leak detection linings and leak detection jackets |
| ISO 4892-1:2016 | Plastics — Methods of exposure to laboratory light sources — Part 1: General guidance |
| ISO 2719:2016 | Determination of flash point — Pensky-Martens closed cup method |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| EN ISO 4892-1:2016 | Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 4892-1:2016) |
| EN 13160-2:2016 | Leak detection systems - Part 2: Requirements and test/assessment methods for pressure and vacuum systems |
| EN ISO 527-2:2012 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| EN 13160-5:2016 | Leak detection systems - Part 5: Requirements and test/assessment methods for in-tank gauge systems and pressurised pipework systems |
| EN ISO 15512:2016 | Plastics - Determination of water content (ISO 15512:2016) |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| EN ISO 293:2005 | Plastics - Compression moulding of test specimens of thermoplastic materials (ISO 293:2004) |
| EN 13160-6:2016 | Leak detection systems - Part 6: Sensors in monitoring wells |
| EN 13160-3:2016 | Leak detection systems - Part 3: Requirements and test/assessment methods for liquid systems for tanks |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 175:2010 | Plastics Methods of test for the determination of the effects of immersion in liquid chemicals |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 1872-2:2007 | Plastics Polyethylene (PE) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 1183-2:2004 | Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 15512:2016 | Plastics Determination of water content |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| EN ISO 2719:2016 | Determination of flash point - Pensky-Martens closed cup method (ISO 2719:2016) |
| EN ISO 1872-2:2007 | Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1872-2:2007) |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| EN 13160-4:2016 | Leak detection systems - Part 4: Requirements and test/assessment methods for sensor based leak detection systems |
| EN ISO 4892-2:2013 | Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013) |
| ISO 1133:2005 | Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| EN 13160-1:2016 | Leak detection systems - Part 1: General Principles |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
| CLC/TR 50404:2003 | Electrostatics - Code of practice for the avoidance of hazards due to static electricity |
| EN ISO 175:2010 | Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:2010) |
| EN ISO 1183-2:2004 | Plastics - Methods for determining the density of non-cellular plastics - Part 2: Density gradient column method (ISO 1183-2:2004) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.