Skip to content
Please enter a keyword to search

  • EN 13341:2005+A1:2011

    Current The latest, up-to-date edition.

    Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6 - Requirements and test methods

    Available format(s): 

    Language(s): 

    Published date:  12-01-2011

    Publisher:  Comite Europeen de Normalisation

    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Requirements
    5 Evaluation of conformity
    6 Requirements for tanks
    7 Durability
    8 Marking, transport, handling and installation of tanks
    Annex A (normative) - Test methods for determination of
            material characteristics
    Annex B (normative) - Test methods for determination of
            tank characteristics
    Annex ZA (informative) - Clauses of this European
             Standard addressing essential requirements
             or other provisions of EU Directives
    Bibliography

    Abstract - (Show below) - (Hide below)

    This document specifies requirements for materials, physical properties and performance of single blow moulded and rotationally moulded polyethylene tanks and of rotationally moulded tanks made of anionically polymerized polyamide 6, with or without reinforcements, for above ground storage of domestic heating oil, kerosene and diesel fuels for the supply of building heating/cooling systems.It is only applicable to static blow moulded and rotationally moulded polyethylene tanks and to rotationally moulded tanks made of anionically polymerized polyamide 6 that are subject to atmospheric pressure, but not subject to any external loading and have a capacity from 400 l up to 10 000 l.

    General Product Information - (Show below) - (Hide below)

    Committee CEN/TC 249
    Development Note 2005 Edition Re-Issued in January 2011 & incorporates AMD 1 2011. (03/2011)
    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Current

    Standards Referenced By This Book - (Show below) - (Hide below)

    14/30301257 DC : 0 BS EN 13160-3 - LEAK DETECTION SYSTEMS - PART 3: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR LIQUID SYSTEMS FOR TANKS
    EEMUA 225 : 1920 ABOVE GROUND PLASTIC TANKS - A GUIDE TO THEIR SPECIFICATION, INSTALLATION, COMMISSIONING, INSPECTION, MAINTENANCE, REPAIR AND DISPOSAL
    EN 13575:2012 Static thermoplastic tanks for the above ground storage of chemicals — Blow moulded or rotationally moulded polyethylene tanks — Requirements and test methods
    EN 13160-3:2016 Leak detection systems - Part 3: Requirements and test/assessment methods for liquid systems for tanks
    09/30202307 DC : 0 BS EN 12514-1 - PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 1: SAFETY REQUIREMENTS AND TESTS - TERMINOLOGY, GENERAL REQUIREMENTS
    10/30233680 DC : 0 BS EN 13575 - STATIC THERMOPLASTIC TANKS FOR THE ABOVE GROUND STORAGE OF CHEMICALS - BLOW MOULDED OR ROTATIONALLY MOULDED POLYETHYLENE TANKS - REQUIREMENTS AND TEST METHODS
    UNE-EN 13575:2012 Static thermoplastic tanks for the above ground storage of chemicals — Blow moulded or rotationally moulded polyethylene tanks — Requirements and test methods
    I.S. EN 13160-3:2016 LEAK DETECTION SYSTEMS - PART 3: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR LIQUID SYSTEMS FOR TANKS
    I.S. EN 13575:2012 STATIC THERMOPLASTIC TANKS FOR THE ABOVE GROUND STORAGE OF CHEMICALS - BLOW MOULDED OR ROTATIONALLY MOULDED POLYETHYLENE TANKS - REQUIREMENTS AND TEST METHODS
    VDI 3833 Blatt 1:2014-09 Dynamic damper and dynamic vibration absorber - Dynamic damper - Fundamentals, characteristics, implementation, application
    UNI EN 13575 : 2012 STATIC THERMOPLASTIC TANKS FOR THE ABOVE GROUND STORAGE OF CHEMICALS - BLOW MOULDED OR ROTATIONALLY MOULDED POLYETHYLENE TANKS - REQUIREMENTS AND TEST METHODS
    15/30317327 DC : 0 BS EN 16941-1 - ON-SITE NON-POTABLE WATER SYSTEMS - PART 1: SYSTEMS FOR THE USE OF RAINWATER
    BS EN 13575:2012 Static thermoplastic tanks for the above ground storage of chemicals. Blow moulded or rotationally moulded polyethylene tanks. Requirements and test methods
    UNE-EN 13160-3:2017 Leak detection systems - Part 3: Requirements and test/assessment methods for liquid systems for tanks
    PREN 13160-3 : DRAFT 2014 LEAK DETECTION SYSTEMS - PART 3: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR LIQUID SYSTEMS FOR TANKS
    DIN EN 13575:2012-06 Static thermoplastic tanks for the above ground storage of chemicals - Blow moulded or rotationally moulded polyethylene tanks - Requirements and test methods

    Standards Referencing This Book - (Show below) - (Hide below)

    93/68/EEC : 1993 AMD 2 1998 COUNCIL DIRECTIVE 93/68/EEC OF 22.7.93 AMENDING DIRECTIVES 87/404/EEC, 88/378/EEC, 89/106/EEC, 89/336/EEC, 89/392/EEC, 89/686/EEC, 90/384/EEC, 90/385/EEC, 90/396/EEC, 91/263/EEC, 92/42/EEC AND 73/23/EEC
    EN 13160-7:2016 Leak detection systems - Part 7: Requirements and test/assessment methods for interstitial spaces, leak detection linings and leak detection jackets
    ISO 4892-1:2016 Plastics Methods of exposure to laboratory light sources Part 1: General guidance
    ISO 2719:2016 Determination of flash point — Pensky-Martens closed cup method
    ISO 293:2004 Plastics — Compression moulding of test specimens of thermoplastic materials
    EN ISO 4892-1:2016 Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 4892-1:2016)
    EN 13616:2004/AC:2006 OVERFILL PREVENTION DEVICES FOR STATIC TANKS FOR LIQUID PETROLEUM FUELS
    EN 13160-2:2016 Leak detection systems - Part 2: Requirements and test/assessment methods for pressure and vacuum systems
    89/106/EEC : 1988 COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS
    EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
    EN 13160-5:2016 Leak detection systems - Part 5: Requirements and test/assessment methods for in-tank gauge systems and pressurised pipework systems
    EN ISO 15512:2016 Plastics - Determination of water content (ISO 15512:2016)
    ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
    EN ISO 293:2005 Plastics - Compression moulding of test specimens of thermoplastic materials (ISO 293:2004)
    EN 13160-6:2016 Leak detection systems - Part 6: Sensors in monitoring wells
    EN 13160-3:2016 Leak detection systems - Part 3: Requirements and test/assessment methods for liquid systems for tanks
    EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
    ISO 175:2010 Plastics Methods of test for the determination of the effects of immersion in liquid chemicals
    ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
    ISO 1872-2:2007 Plastics Polyethylene (PE) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
    ISO 1183-2:2004 Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
    ISO 9001:2015 Quality management systems — Requirements
    ISO 15512:2016 Plastics Determination of water content
    ISO 4892-2:2013 Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
    EN ISO 2719:2016 Determination of flash point - Pensky-Martens closed cup method (ISO 2719:2016)
    EN ISO 1872-2:2007 Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1872-2:2007)
    EN ISO 1133:2005 PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS
    EN 13160-4:2016 Leak detection systems - Part 4: Requirements and test/assessment methods for sensor based leak detection systems
    EN ISO 4892-2:2013 Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013)
    ISO 1133:2005 Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
    EN 13160-1:2016 Leak detection systems - Part 1: General Principles
    EN ISO 1183-1:2012 Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012)
    CLC/TR 50404:2003 Electrostatics - Code of practice for the avoidance of hazards due to static electricity
    EN ISO 175:2010 Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:2010)
    EN ISO 1183-2:2004 PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 2: DENSITY GRADIENT COLUMN METHOD
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective