Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN 13483:2013

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES WITH INTERNAL VAPOUR RECOVERY FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION

    Available format(s):  Hardcopy, PDF

    Superseded date:  29-05-2023

    Language(s):  English

    Published date:  01-01-2013

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Classification
    5 Materials and construction
    6 Pressure requirements
    7 Dimensions and tolerances
    8 Physical properties
    9 End fittings
    10 Type tests
    11 Frequency of testing
    12 Marking
    Annex A (normative) - Test method for determination
            of low temperature class resistance at
            -30 degrees C (for normal temperature
            class) and -40 degrees C (for low
            temperature class)
    Annex B (normative) - Test method for pressure
            requirements of vapour recovery hoses and tubes
    Annex C (normative) - Test method for determination
            of change in length due to swelling
    Annex D (normative) - Test method for determination
            of pressure loss
    Annex E (normative) - Method for determination of
            adhesion between components
    Annex F (normative) - Test method for the
            determination of low temperature flexibility
    Annex G (normative) - Test method for the
            determination of rate of fuel permeation
    Annex H (normative) - Test method for flammability
    Annex I (normative) - Test method for the
            determination of leakage (leak test)
    Annex J (normative) - Test method for fatigue
            strength under reversed bending stresses
            (flex test)
    Annex K (normative) - End-fitting pull-off test
    Annex L (normative) - Test frequency for type
            tests and routine tests
    Annex M (informative) - Test frequency for
            production acceptance tests
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes the requirements and test methods for verification for hose assemblies with vapour recovery for delivery systems on petrol filling stations.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN ISO 8330:2014 Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330:2014)
    EN ISO 1402:2009 Rubber and plastics hoses and hose assemblies - Hydrostatic testing (ISO 1402:2009)
    EN ISO 4671:2007/A1:2011 Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies - Amendment 1: Clarification of position at which outside diameter is measured (ISO 4671:2007/Amd 1:2011)
    EN 228:2012+A1:2017 Automotive fuels - Unleaded petrol - Requirements and test methods
    ISO 6801:1983 Rubber or plastics hoses Determination of volumetric expansion
    ISO 4649:2017 Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device
    EN ISO 1307:2008 Rubber and plastics hoses - Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses (ISO 1307:2006)
    ISO 188:2011 Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
    EN ISO 8031:2009 Rubber and plastics hoses and hose assemblies - Determination of electrical resistance and conductivity (ISO 8031:2009)
    EN ISO 7326:2016 Rubber and plastics hoses - Assessment of ozone resistance under static conditions (ISO 7326:2016)
    ISO 7326:2016 Rubber and plastics hoses Assessment of ozone resistance under static conditions
    EN ISO 8033:2017 Rubber and plastics hoses - Determination of adhesion between components (ISO 8033:2016)
    ISO 8330:2007 Rubber and plastics hoses and hose assemblies Vocabulary
    ISO 10619-1:2011 Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 1: Bending tests at ambient temperature
    EN 26801:1993/A1:2011 RUBBER OR PLASTICS HOSES - DETERMINATION OF VOLUMETRIC EXPANSION (ISO 6801:1983/AMD 1:2011)
    ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
    ISO 4671:2007 Rubber and plastics hoses and hose assemblies Methods of measurement of the dimensions of hoses and the lengths of hose assemblies
    ISO 554:1976 Standard atmospheres for conditioning and/or testing — Specifications
    ISO 1402:2009 Rubber and plastics hoses and hose assemblies Hydrostatic testing
    ISO 1307:2006 Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses
    ISO 8033:2016 Rubber and plastics hoses Determination of adhesion between components
    ISO 8031:2009 Rubber and plastics hoses and hose assemblies Determination of electrical resistance and conductivity
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective