• I.S. EN 61249-2-6:2005/AC:2005

    Current The latest, up-to-date edition.

    MATERIALS FOR PRINTED BOARDS AND OTHER INTERCONNECTING STRUCTURES - PART 2-6: REINFORCED BASE MATERIALS, CLAD AND UNCLAD - BROMINATED EPOXIDE NON-WOVEN/WOVEN E-GLASS REINFORCED LAMINATED SHEETS OF DEFINED FLAMMABILITY (VERTICAL BURNING TEST), COPPER-CLAD

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2005

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    1 Scope
    2 Normative references
    3 Materials and construction
       3.1 Resin system
       3.2 Reinforcement
       3.3 Metal foil
    4 Internal marking
    5 Electrical properties
    6 Non-electrical properties of the copper clad laminate
       6.1 Appearance of the copper clad sheet
       6.2 Appearance of the unclad face
       6.3 Laminate thickness
       6.4 Bow and twist
       6.5 Properties related to the copper foil bond
       6.6 Punching and machining
       6.7 Dimensional stability
       6.8 Sheet size
       6.9 Cut panels
    7 Non-electrical properties of the base material after complete
       removal of the copper foil
       7.1 Appearance of the dielectric base material
       7.2 Flexural strength
       7.3 Flammability
       7.4 Water absorption
       7.5 Measling
       7.6 Glass transition temperature and cure factor
    8 Quality assurance
       8.1 Quality system
       8.2 Responsibility for inspection
       8.3 Qualification inspection
       8.4 Quality conformance inspection
       8.5 Certificate of conformance
       8.6 Safety data sheet
    9 Packaging and marking
    10 Ordering information
    Annex A (informative) Engineering information
    Annex B (informative) Common laminate constructions
    Annex C (informative) Guideline for qualification and
                           conformance inspection
    Annex ZA (normative) Normative references to international
                           publications with their corresponding
                           European publications
    Bibliography

    Abstract - (Show below) - (Hide below)

    Specifies requirements for properties of brominated epoxide non-woven/woven reinforced E-glass laminated sheets of defined flammability, copper-clad in thicknesses of 0,80 mm up to 1,70 mm.

    General Product Information - (Show below) - (Hide below)

    Development Note For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 61249-5-1 : 1996 MATERIALS FOR INTERCONNECTION STRUCTURES - PART 5: SECTIONAL SPECIFICATION SET FOR CONDUCTIVE FOILS AND FILMS WITH AND WITHOUT COATINGS - SECTION 1: COPPER FOILS (FOR THE MANUFACTURE OF COPPER-CLAD BASE MATERIALS)
    ISO 11014-1:1994 Safety data sheet for chemical products Part 1: Content and order of sections
    IEC 61249-5-1:1995 Materials for interconnection structures - Part 5: Sectional specification set for conductive foils and films with and without coatings - Section 1: Copper foils (for the manufacture of copper-clad base materials)
    ISO 14001:2015 Environmental management systems Requirements with guidance for use
    IEC 60194:2015 Printed board design, manufacture and assembly - Terms and definitions
    EN ISO 14001 : 2015 ENVIRONMENTAL MANAGEMENT SYSTEMS - REQUIREMENTS WITH GUIDANCE FOR USE (ISO 14001:2015)
    ISO 9000:2015 Quality management systems Fundamentals and vocabulary
    IEC 61189-2:2006 Test methods for electrical materials, printed boards and other interconnection structures and assemblies - Part 2: Test methods for materials for interconnection structures
    EN ISO 9000 : 2015 QUALITY MANAGEMENT SYSTEMS - FUNDAMENTALS AND VOCABULARY (ISO 9000:2015)
    EN 61189-2 : 2006 TEST METHODS FOR ELECTRICAL MATERIALS, PRINTED BOARDS AND OTHER INTERCONNECTION STRUCTURES AND ASSEMBLIES - PART 2: TEST METHODS FOR MATERIALS FOR INTERCONNECTION STRUCTURES
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective