I.S. EN 61298-3:2008
Current
The latest, up-to-date edition.
PROCESS MEASUREMENT AND CONTROL DEVICES - GENERAL METHODS AND PROCEDURES FOR EVALUATING PERFORMANCE - PART 3: TESTS FOR THE EFFECTS OF INFLUENCE QUANTITIES
Hardcopy , PDF
English
01-01-2008
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General considerations
4.1 Criteria
4.2 General procedures
4.3 General EMC requirements
5 Ambient temperature effects
5.1 Criteria
5.2 Test procedure
6 Ambient relative humidity effects
7 Vibration
7.1 General considerations
7.2 Initial resonance search
7.3 Endurance conditioning by sweeping
7.4 Final resonance search
7.5 Final measurements
8 Shock, drop and topple
9 Mounting position
10 Over-range
11 Output load effects
11.1 Electrical output
11.2 Pneumatic output
12 Power supply
12.1 Supply voltage and frequency variations
12.2 Transient supply voltage effects
12.3 Supply voltage depression
12.4 Short-term supply voltage interruptions
12.5 Fast transient/burst immunity requirements
12.6 Surge immunity requirements
12.7 Reverse supply voltage protection (d.c. devices)
12.8 Supply pressure variations
12.9 Supply pressure interruptions
12.10 Conducted radio frequency requirements
13 Superimposed voltages
13.1 Line to earth voltages
13.2 Line to line voltages (series mode)
13.3 Earthing
14 Harmonic distortion effects
15 Magnetic field effects
16 Electromagnetic field immunity test
17 Electrostatic discharge
18 Effect of open-circuited and short-circuited input
19 Effect of open-circuited and short-circuited output
20 Effects of process medium conditions
20.1 Temperature of process fluid
20.2 Flow of process fluid through the device
20.3 Static line pressure effect
21 Atmospheric pressure effects
22 Flow of purge gas through the device
23 Accelerated operational life test
24 Operational long-term drift test (optional)
Annex ZA (normative) Normative references to international
publications with their corresponding European
publications
Bibliography
Describes general methods and procedures for conducting tests and reporting on the functional and performance characteristics of process measurement and control devices.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
70
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| NBN EN 61298-3 : 2009 | Identical |
| NF EN 61298-3 : 2009 | Identical |
| DIN EN 61298-3:2009-08 | Identical |
| IEC 61298-3:2008 | Identical |
| EN 61298-3:2008 | Identical |
| BS EN 61298-3:2008 | Identical |
| SN EN 61298-3 : 1998 | Identical |
| IEC 60050-351:2013 | International Electrotechnical Vocabulary (IEV) - Part 351: Control technology |
| EN 60654-2:1997 | Operating conditions for industrial-process measurement and control equipment - Part 2: Power |
| EN 61298-1:2008 | PROCESS MEASUREMENT AND CONTROL DEVICES - GENERAL METHODS AND PROCEDURES FOR EVALUATING PERFORMANCE - PART 1: GENERAL CONSIDERATIONS |
| IEC 61326-3-2:2017 | Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 3-2: Immunity requirements for safety-related systems and for equipment intended to perform safety-related functions (functional safety) - Industrial applications with specified electromagnetic environment |
| IEC 61298-1:2008 | Process measurement and control devices - General methods and procedures for evaluating performance - Part 1: General considerations |
| IEC 61298-2:2008 | Process measurement and control devices - General methods and procedures for evaluating performance - Part 2: Tests under reference conditions |
| EN 61298-2:2008 | PROCESS MEASUREMENT AND CONTROL DEVICES - GENERAL METHODS AND PROCEDURES FOR EVALUATING PERFORMANCE - PART 2: TESTS UNDER REFERENCE CONDITIONS |
| EN 61000-4-11:2004/A1:2017 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-11: TESTING AND MEASUREMENT TECHNIQUES - VOLTAGE DIPS, SHORT INTERRUPTIONS AND VOLTAGE VARIATIONS IMMUNITY TESTS (IEC 61000-4-11:2004/A1:2017) |
| EN 61298-4:2008 | Process measurement and control devices - General methods and procedures for evaluating performance - Part 4: Evaluation report content |
| EN 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| IEC 61326-2-5:2012 | Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-5: Particular requirements - Test configurations, operational conditions and performance criteria for field devices with field bus interfaces according to IEC 61784-1 |
| IEC 61326-2-3:2012 | Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-3: Particular requirements - Test configuration, operational conditions and performance criteria for transducers with integrated or remote signal conditioning |
| EN 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 61000-4-11:2004+AMD1:2017 CSV | Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests |
| IEC 61000-4-8:2009 | Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test |
| IEC 61000-4-4:2012 RLV | Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test |
| EN 61000-4-2:2009 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| IEC 60068-2-31:2008 | Environmental testing - Part 2-31: Tests - Test Ec: Rough handling shocks, primarily for equipment-type specimens |
| IEC 61000-4-6:2013 | Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields |
| EN 61000-4-3 : 2006 AMD 2 2010 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-3: TESTING AND MEASUREMENT TECHNIQUES - RADIATED, RADIO-FREQUENCY, ELECTROMAGNETIC FIELD IMMUNITY TEST |
| EN 61326-1:2013 | Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1: General requirements |
| EN 60654-3:1997 | Operating conditions for industrial-process measurement and control equipment - Part 3: Mechanical influences |
| EN 61000-4-8:2010 | Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 61000-4-2:2008 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV | Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test |
| EN 60654-1:1993 | Industrial-process measurement and control equipment - Operating conditions - Part 1: Climatic conditions |
| IEC 61298-4:2008 | Process measurement and control devices - General methods and procedures for evaluating performance - Part 4: Evaluation report content |
| EN 60068-2-6:2008 | Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
| EN 61000-4-4:2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST (IEC 61000-4-4:2012) |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| EN 61000-4-6:2014/AC:2015 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS (IEC 61000-4-6:2013) |
| IEC 60654-1:1993 | Industrial-process measurement and control equipment - Operating conditions - Part 1: Climatic conditions |
| EN 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
| IEC 60050-300:2001 | International Electrotechnical Vocabulary (IEV) - Part 300: Electrical and electronic measurements and measuring instruments - Part 311: General terms relating to measurements - Part 312: General terms relating to electrical measurements - Part 313: Types of electrical measuring instruments - Part 314: Specific terms according to the type of instrument |
| IEC 61326-3-1:2017 | Electrical equipment for measurement, control and laboratory use - EMC requirements – Part 3-1: Immunity requirements for safety-related systems and for equipment intended to perform safety-related functions (functional safety) – General industrial applications |
| IEC 60654-3:1983 | Operating conditions for industrial-process measurement and control equipment - Part 3: Mechanical influences |
| EN 60068-2-31:2008 | ENVIRONMENTAL TESTING - PART 2-31: TESTS - TEST EC: ROUGH HANDLING SHOCKS, PRIMARILY FOR EQUIPMENT-TYPE SPECIMENS |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.