I.S. EN 62271-102:2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 102: ALTERNATING CURRENT DISCONNECTORS AND EARTHING SWITCHES (IEC 62271-102:2001 (EQV))
Hardcopy , PDF
29-01-2017
English
01-01-2005
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National Foreword
FOREWORD
1 General
2 Normal and special service conditions
3 Definitions
4 Ratings
5 Design and construction
6 Type tests
7 Routine tests
8 Guide to the selection of disconnectors and earthing switches
9 Information to be given with enquiries, tenders and orders
10 Rules for transport, storage, installation, operation and
maintenance
11 Safety
Annex A (normative) - Design and testing of position indicating
devices
Annex B (normative) - Bus-transfer current switching by
disconnectors
Annex C (normative) - Induced current switching by earthing
switches
Annex D (informative) - Test voltage for the most disadvantageous
dielectric position of an earthing switch during
operation (temporary approach)
Annex E (normative) - Special requirements for disconnectors and
earthing switches used in gas-insulated and/or
metal-enclosed switchgear
Annex F (normative) - Gas-insulated metal-enclosed switchgear
for rated voltages 72,5 kV and above - Requirements
for switching of bus-charging currents by disconnectors
Annex G (normative) - Alternative test methods for short-circuit
current making tests
Annex H (normative) - Specific requirements for resistor
fitted disconnector in metal-enclosed gas insulated
switchgear
Bibliography
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
Applicable to alternating current disconnectors and earthing switches, designed for indoor and outdoor enclosed and open terminal installations for voltages above 1000 V and for service frequencies up to and including 60 Hz.
| DevelopmentNote |
Supersedes I.S. EN 60129, I.S. EN 61129 and I.S. EN 61259. (05/2005) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
108
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| Supersedes |
| Standards | Relationship |
| EN 62271-102:2002/AC:2014 | Identical |
| NBN EN 62271-102 : 2003 COR 2015 | Identical |
| NF EN 62271-102 : 2005 AMD 2 2013 | Identical |
| DIN EN 62271-102 : 2012 COR 1 2016 | Identical |
| IEC 62271-102:2001+AMD1:2011+AMD2:2013 CSV | Identical |
| BS EN 62271-102 : 2002 | Identical |
| UNE-EN 62271-102:2005 | Identical |
| IEC 62271-100:2008+AMD1:2012+AMD2:2017 CSV | High-voltage switchgear and controlgear - Part 100: Alternating-current circuit-breakers |
| EN 60517:1996/A11:1999 | GAS-INSULATED METAL-ENCLOSED SWITCHGEAR FOR RATED VOLTAGES OF 72,5 KV AND ABOVE |
| EN 60265-2:1993/A2:1998 | HIGH-VOLTAGE SWITCHES - HIGH-VOLTAGE SWITCHES FOR RATED VOLTAGES OF 52 KV AND ABOVE |
| EN 62271-1:2017 | High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear |
| IEC 60265-2:1988 | High-voltage switches. Part 2: High-voltage switches for rated voltages of 52 kV and above |
| IEC 62271-101:2012 | High-voltage switchgear and controlgear - Part 101: Synthetic testing |
| IEC 60517:1990 | Gas-insulated metal-enclosed switchgear for rated voltages of 72.5 kV and above |
| IEC 60694:1996+AMD1:2000+AMD2:2001 CSV | Common specifications for high-voltage switchgear and controlgear standards |
| EN 60298:1996/A11:1999 | A.C. METAL-ENCLOSED SWITCHGEAR AND CONTROLGEAR FOR RATED VOLTAGES ABOVE 1 KV AND UP TO AND INCLUDING 52 KV |
| IEC 60865-1:2011 | Short-circuit currents - Calculation of effects - Part 1: Definitions and calculation methods |
| EN 60694:1996/A2:2001 | COMMON SPECIFICATIONS FOR HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR STANDARDS |
| IEC 60137:2017 | Insulated bushings for alternating voltages above 1000 V |
| EN 22768-1:1993 | General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1:1989) |
| EN 60865-1:2012 | Short-circuit currents - Calculation of effects - Part 1: Definitions and calculation methods |
| EN 60265-1:1998 | High-voltage switches - Part 1: Switches for rated voltages above 1 kV and less than 52 kV |
| IEC 62271-1:2017 | High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear |
| IEC TR 62271-305:2009 | High-voltage switchgear and controlgear - Part 305: Capacitive current switching capability of air-insulated disconnectors for rated voltages above 52 kV |
| IEC 60298:1990 | A.C. metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.