I.S. EN 877:2000
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE
Hardcopy , PDF
17-11-2021
English
01-01-2000
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
1 Scope
2 Normative References
3 Definitions
4 Technical Requirements
4.1 General
4.2 Dimensions
4.3 Interconnection
4.4 Mass
4.5 Material characteristics of pipes, fittings and accessories
4.6 Coatings for pipes, fittings and accessories
4.7 Joints
4.8 Buried systems
4.9 Rainwater systems installed outside buildings
4.10 Marking
5 Test Methods
5.1 Surface condition
5.2 Dimensions
5.3 Mass
5.4 Tensile strength of pipes and fittings
5.5 Brinell hardness
5.6 Ring crush test for grey cast iron pipes
5.7 Coatings
5.8 Joints
5.9 Buried systems
5.10 Rainwater systems installed outside buildings
5.11 Marking
6 Evaluation of conformity
Annex A (informative) Other dimensions for buried systems
Annex B (informative) Other dimensions for rainwater systems to
be installed outside buildings
Annex C (informative) Field of use for buried pipes and fittings,
characteristics of soils, load-bearing capacity
Annex D (normative) Evaluation of conformity
Annex E (informative) Surveillance by an accredited third
party (certification by third party)
Annex F (informative) General information on some product
characteristics
Annex G (informative) Method of calculation of gross calorific
potential of external coatings for the
range, noted PCS[range ext. coating]
Annex H (normative) Reaction to fire test (SBI
adaptation for testing a products range)
Annex ZA (informative) Clauses of the European Standard
addressing essential requirements or other provisions
of EU Directives
Bibliography
Defines cast iron pipeline components used for the construction of discharge systems for drains and building normally as gravity systems. The range is from DN 40 to DN 600 inclusive. Covers requirements for the dimensions and tolerances, appearance, materials, mechanical properties, standard coatings for cast iron pipes, fittings and accessories. These cover all components including joints. Quality assurance is covered in an information annex.
| DocumentType |
Standard
|
| Pages |
86
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| UNE-EN 877:2000 | Identical |
| NF EN 877 : 1999 AMD 1 2006 | Identical |
| NS EN 877 : 1999 AC 2008 | Identical |
| NBN EN 877 : 1999 COR 2008 | Identical |
| NEN EN 877 : 1999 AMD 1/C1 2008 | Identical |
| BS EN 877 : 1999 | Identical |
| UNI EN 877 : 2007 | Identical |
| DIN EN 877:2010-01 | Identical |
| SN EN 877 : 1999 CORR 2008 | Identical |
| ONORM EN 877 : 2008 | Identical |
| ISO 7724-1:1984 | Paints and varnishes Colorimetry Part 1: Principles |
| EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| ISO 898-2:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread |
| EN 605 : 1992 | PAINTS AND VARNISHES - STANDARD PANELS FOR TESTING |
| ISO 1716:2010 | Reaction to fire tests for products Determination of the gross heat of combustion (calorific value) |
| EN 20898-1 : 1991 | MECHANICAL PROPERTIES OF FASTENERS - BOLTS, SCREWS AND STUDS |
| EN 598:2007+A1:2009 | Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods |
| ISO 2808:2007 | Paints and varnishes Determination of film thickness |
| EN 10088-3:2014 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| EN 45011:1998 | General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996) |
| ISO 7724-2:1984 | Paints and varnishes Colorimetry Part 2: Colour measurement |
| ISO 11925-2:2010 | Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test |
| EN ISO 2409:2013 | Paints and varnishes - Cross-cut test (ISO 2409:2013) |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| EN 20898-2 : 1993 | MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992) |
| EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| EN 45011 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS |
| ISO/IEC 17011:2004 | Conformity assessment General requirements for accreditation bodies accrediting conformity assessment bodies |
| EN 13823:2010+A1:2014 | Reaction to fire tests for building products - Building products excluding floorings exposed to the thermal attack by a single burning item |
| EN ISO 6708:1995 | Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
| ISO 4628-3:2016 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 3: Assessment of degree of rusting |
| ISO 7253:1996 | Paints and varnishes — Determination of resistance to neutral salt spray (fog) |
| EN 476:2011 | General requirements for components used in drains and sewers |
| ISO 7724-3:1984 | Paints and varnishes Colorimetry Part 3: Calculation of colour differences |
| EN 1366-3:2009 | Fire resistance tests for service installations - Part 3: Penetration seals |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 2812-1:2017 | Paints and varnishes — Determination of resistance to liquids — Part 1: Immersion in liquids other than water |
| EN 14366:2004 | Laboratory measurement of noise from waste water installations |
| ISO 185:2005 | Grey cast irons Classification |
| EN 10003-1 : 1994 | METALLIC MATERIALS - BRINELL HARDNESS TEST - TEST METHOD |
| PREN 1366-3 : DRAFT 1993 | FIRE TESTS FOR BUILDING ELEMENTS AND COMPONENTS - FIRE RESISTANCE TESTING OF SERVICE INSTALLATIONS - PART 3: PENETRATION SEALS |
| ISO 2409:2013 | Paints and varnishes Cross-cut test |
| EN ISO 1716:2010 | Reaction to fire tests for products - Determination of the gross heat of combustion (calorific value) (ISO 1716:2010) |
| ISO 4628-2:2016 | Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 2: Assessment of degree of blistering |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.