IEC 60243-1:2013
|
Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
|
IEC 60112:2003+AMD1:2009 CSV
|
Method for the determination of the proof and the comparative tracking indices of solid insulating materials
|
ISO 22007-3:2008
|
Plastics Determination of thermal conductivity and thermal diffusivity Part 3: Temperature wave analysis method
|
ISO 3167:2014
|
Plastics Multipurpose test specimens
|
ISO 22007-4:2017
|
Plastics — Determination of thermal conductivity and thermal diffusivity — Part 4: Laser flash method
|
ISO 974:2000
|
Plastics Determination of the brittleness temperature by impact
|
IEC 60250:1969
|
Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
|
ISO 815-1:2014
|
Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures
|
ISO 10350-1:2017
|
Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials
|
ISO 8256:2004
|
Plastics — Determination of tensile-impact strength
|
ISO 11359-2:1999
|
Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
|
ISO 34-1:2015
|
Rubber, vulcanized or thermoplastic Determination of tear strength Part 1: Trouser, angle and crescent test pieces
|
ISO 75-2:2013
|
Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
|
ISO 527-2:2012
|
Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
|
ISO 11357-3:2011
|
Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallization
|
ISO 11357-4:2014
|
Plastics Differential scanning calorimetry (DSC) Part 4: Determination of specific heat capacity
|
ISO 294-4:2001
|
Plastics Injection moulding of test specimens of thermoplastic materials Part 4: Determination of moulding shrinkage
|
IEC 60093:1980
|
Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
|
IEC 60695-11-10:2013
|
Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
|
ISO 1183-1:2012
|
Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
|
ISO 1183-2:2004
|
Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
|
ISO 1183-3:1999
|
Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method
|
ISO 14910-1:2013
|
Plastics Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Part 1: Designation system and basis for specification
|
ISO 179-1:2010
|
Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
|
ISO 15512:2016
|
Plastics Determination of water content
|
ISO 62:2008
|
Plastics Determination of water absorption
|
ISO 306:2013
|
Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
|
ISO 294-1:2017
|
Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
|
ISO 37:2017
|
Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
|
ISO 4589-2:2017
|
Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
|
ISO 22007-2:2015
|
Plastics Determination of thermal conductivity and thermal diffusivity Part 2: Transient plane heat source (hot disc) method
|
ISO 1133-2:2011
|
Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture
|
ISO 899-1:2017
|
Plastics — Determination of creep behaviour — Part 1: Tensile creep
|
ISO 178:2010
|
Plastics Determination of flexural properties
|
ISO 868:2003
|
Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)
|